JLJohn Leggett

John Leggett

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


John Leggett has a total of 6 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Exploring the Presence of Pressure Waves in Axial Compressor Cascades

    by John Leggett, Richard Sandberg

    The presence of pressure waves in an axial compressor cascade are ubiquitous and have been known and investigated for some time. Much of the work to date focuses on compressor acoustics and vibration, which is largely due to wake blade interactions and trailing edge shedding. However, it has been shown on free aerofoils that pressure waves can be produced from volume sources, such as separation, at non-negligible amplitudes. The work presented here highlights the presence of pressure waves emanating from the suction surface transition of a NACA 65 axial compressor cascade, and briefly investigates and details the influence different free-stream disturbances have on the frequency of the pressure waves produced.


  • Loss Analysis of Unsteady Turbomachinery Flows Based on the Mechanical Work Potential

    by John Leggett, Edward Richardson, Stephan Priebe, Aamir Shabbir, Vittorio Michelassi, Richard Sandberg

    Loss analysis is a valuable technique for improving the thermodynamic performance of turbomachines. Analysing loss in terms of the ‘mechanical work potential’ (Miller, R.J., ASME Turbo Expo 2013, GT2013-95488) provides an instantaneous and local account of the thermal and aerodynamic mechanisms contributing to the loss of thermodynamic performance. This study develops the practical application of mechanical work potential loss analysis, providing the mathematical formulations necessary to perform loss analysis using practical Reynolds-Averaged Navier-Stokes (RANS) or Large Eddy Simulations (LES). The analysis approach is demonstrated using RANS and LES of a linear compressor cascade, both with and without incoming wakes. Spatial segmentation is used to attribute loss contributions to specific regions of the flow, and phase-averaging is performed in order to associate the variation of different loss contributions with the periodic passage of wakes through the cascade. For this un-cooled linear cascade, viscous dissipation is the dominant source of loss. The analysis shows that the contribution of the viscous reheat effect depends on the operating pressure of the compressor stage relative to the ambient ‘dead state’ pressure — implying that the optimal blade profile for a low-pressure compressor stage may be different from the optimal profile for a high-pressure compressor stage in the same engine, even if the operating conditions for both stages are dynamically-similar.


  • Loss Prediction in an Axial Compressor Cascade at Off-Design Incidences With Free Stream Disturbances Using Large Eddy Simulation

    by John Leggett, Stephan Priebe, Aamir Shabbir, Vittorio Michelassi, Richard Sandberg, Edward Richardson

    Axial compressors may be operated under off-design incidences due to variable operating conditions. Therefore, a successful design requires accurate performance and stability limits predictions under a wide operating range. Designers generally rely both on correlations and on Reynolds-averaged Navier–Stokes (RANS), the accuracy of the latter often being questioned. The present study investigates profile losses in an axial compressor linear cascade using both RANS and wall-resolved large eddy simulation (LES), and compares with measurements. The analysis concentrates on “loss buckets,” local separation bubbles and boundary layer transition with high levels of free stream turbulence, as encountered in real compressor environment without and with periodic incoming wakes. The work extends the previous research with the intention of furthering our understanding of prediction tools and improving our quantification of the physical processes involved in loss generation. The results show that while RANS predicts overall profile losses with good accuracy, the relative importance of the different loss mechanisms does not match with LES, especially at off-design conditions. This implies that a RANS-based optimization of a compressor profile under a wide incidence range may require a thorough LES verification at off-design incidence.


  • LES Loss Prediction in an Axial Compressor Cascade at Off-Design Incidences With Free Stream Disturbances

    by John Leggett, Stephan Priebe, Aamir Shabbir, Richard Sandberg, Edward Richardson, Vittorio Michelassi

    It is well known that an axial compressor cascade will exhibit variation in loss coefficient, described as a loss bucket, when run over a sweep of incidences, and that higher levels of free stream turbulence are likely to suppress separation bubbles and cause earlier transition (see e.g. [23]). However, it remains difficult to achieve accurate quantitative prediction of these changes using numerical simulation, particularly at off-design conditions, without the added computational expense of using eddy-resolving techniques. The aim of the present study is to investigate profile losses in an axial compressor under such conditions using wall-resolved Large Eddy Simulation (LES) and RANS. The work extends on previous work by Leggett et al.[11] with the intention of furthering our understanding of loss prediction tools and improving our quantification of the physical processes involved in loss generation. The results show that while RANS predicts losses with good accuracy the breakdown of these losses are attributed to different processes, meaning that optimisation of a compressor cascade profile, based solely on RANS, may be hard to achieve.


  • Detailed Investigation of RANS and LES Predictions of Loss Generation in an Axial Compressor Cascade at Off Design Incidences

    by John Leggett, Stephan Priebe, Richard Sandberg, Vittorio Michelassi, Aamir Shabbir

    In the design of modern jet engines the need for accurate loss prediction techniques is ever present. The most common tool currently in use is Reynolds Averaged Navier-Stokes model which provides good estimation at design conditions but can struggle with off design conditions. With accuracy being such an important requirement, an alternative method such as Large Eddy Simulation presents an opportunity to improve and assess the off design performance. Although still limited by computational resources, the use of Large Eddy Simulations in conjunction with more detailed loss analysis methods forms a powerful tool for assessing and improving current Reynolds Averaged Navier-Stokes techniques. The simulations performed here are an incidence sweep at off-design conditions with free stream turbulence. The results of the two methodologies are compared with the use of loss breakdown analysis and the best practice of applying the loss breakdown technique to compressors is outlined.