Natalia N. Orekhova
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Natalia N. Orekhova has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
Nosov Magnitogorsk State Technical University
4 shared publications- I. V. Shadrunova
Russian Academy of Sciences
2 shared publications - Nikita Osintsev
Nosov Magnitogorsk State Technical University, Russia
2 shared publications - Aleksandr Rakhmangulov
Nosov Magnitogorsk State Technical University, Russia
1 shared publication Andrey Yu. Tyulenev
1 shared publicationD S Muravev
Mining Engineering and Transport Institute, Nosov Magnitogorsk State Technical University, Pr. Lenina, 38, Magnitogorsk, Russia
1 shared publication
Latest Publications
- 30 June 2025
- Published by Nosov Magnitogorsk State Technical University in Vestnik of Nosov Magnitogorsk State Technical University
- Vol. 23 (2)
Reduction of Mechanical Entrainment of Silica-Bearing Gangue Minerals to Concentrate by Optimizing the Operating Parameters of the Technological Process
Efficient beneficiation of polymetallic ores is an essential issue, which has become more difficult due to the mineral complexity of ores, lower metal grades and fine dissemination of minerals. The purpose of the study was to identify the relative importance of changes in pulp density, airflow rate and impeller speed at their aggregate impact on reduction of the mechanical entrainment of fine gangue mineral particles, and to establish the control limits of their values in the zinc cycle of polymetallic ore flotation. In this study the effect of mechanical entrainment of silica-containing minerals on the reduced quality of froth product of zinc cycle of polymetallic ore flotation was evaluated. The experiments were performed to establish the operating range of optimal process parameters, providing efficient sphalerite flotation and minimizing the extraction of SiO2 in the concentrate. The negative impact of excessive reduction of each of the controlled parameters has been experimentally revealed. By mathematical processing of the results of the complete factorial experiment the regression equation was obtained, which appropriately describes the correlation between the controlled process parameters and the ratio of mechanical entrainment of gangue minerals that enables more accurate prediction of the results when altering flotation conditions. Airflow rate was found to be the most significant factor. The reasonable decision on streamlining performance parameters of the existing production by implementation of the obtained results provided, at the initial stage, reduction of mass fraction of SiO2 in zinc concentrate by 15.66% of the initial level.
- 30 June 2025
- Published by Nosov Magnitogorsk State Technical University in Vestnik of Nosov Magnitogorsk State Technical University
- Vol. 23 (2)
Reduction of Mechanical Entrainment of Silica-Bearing Gangue Minerals to Concentrate by Optimizing the Operating Parameters of the Technological Process
Efficient beneficiation of polymetallic ores is an essential issue, which has become more difficult due to the mineral complexity of ores, lower metal grades and fine dissemination of minerals. The purpose of the study was to identify the relative importance of changes in pulp density, airflow rate and impeller speed at their aggregate impact on reduction of the mechanical entrainment of fine gangue mineral particles, and to establish the control limits of their values in the zinc cycle of polymetallic ore flotation. In this study the effect of mechanical entrainment of silica-containing minerals on the reduced quality of froth product of zinc cycle of polymetallic ore flotation was evaluated. The experiments were performed to establish the operating range of optimal process parameters, providing efficient sphalerite flotation and minimizing the extraction of SiO2 in the concentrate. The negative impact of excessive reduction of each of the controlled parameters has been experimentally revealed. By mathematical processing of the results of the complete factorial experiment the regression equation was obtained, which appropriately describes the correlation between the controlled process parameters and the ratio of mechanical entrainment of gangue minerals that enables more accurate prediction of the results when altering flotation conditions. Airflow rate was found to be the most significant factor. The reasonable decision on streamlining performance parameters of the existing production by implementation of the obtained results provided, at the initial stage, reduction of mass fraction of SiO2 in zinc concentrate by 15.66% of the initial level.
- 25 December 2024
- Published by Ore and Metals Publishing House in Obogashchenie Rud
- No. 6,p. 25-31
Enhancing the efficiency of hydromineral raw material processing through preliminary precipitation of macrocomponents from brines
Hydromineral resources, such as the underground brines from oil and gas fields, are a promising source for the extraction of strategic metals, particularly lithium, as well as other valuable products like magnesium and calcium salts. To improve the efficiency of selective extraction of valuable components from hydromineral raw materials, this study investigates the potential for reducing the concentration of macrocomponents during the initial stages of the processing workflow. Chemical analysis of brines from various oil and gas fields in the Irkutsk region revealed their high mineralization, driven by the presence of calcium, magnesium, potassium, and sodium chlorides, alongside significant concentrations of microcomponents such as lithium (Li) and strontium (Sr). The phase composition of the raw underground brines, primarily consisting of tachyhydrite and sinjarite, was examined, along with post-precipitation product samples, which contained substantial amounts of strontium chloride hydrate. The study demonstrates the feasibility of separating brine components by transferring the majority of calcium, potassium, and iron into the precipitate. The parameters influencing the precipitation process and their effect on the quality of the resulting products were established. Subsequent sorption extraction of lithium and ion-exchange purification of the primary lithium concentrate enabled the production of a lithium-containing product with minimal impurities, achieving over 86 % lithium recovery. As a result, the concentration of major macrocomponents in the primary lithium concentrate was significantly reduced compared to the original brine: calcium to 0.18 % by weight, potassium to 15 % by weight, magnesium to 0.19 % by weight, and iron (II) to less than 0.02 % by weight.
- 25 December 2024
- Published by Ore and Metals Publishing House in Obogashchenie Rud
- No. 6,p. 25-31
Enhancing the efficiency of hydromineral raw material processing through preliminary precipitation of macrocomponents from brines
Hydromineral resources, such as the underground brines from oil and gas fields, are a promising source for the extraction of strategic metals, particularly lithium, as well as other valuable products like magnesium and calcium salts. To improve the efficiency of selective extraction of valuable components from hydromineral raw materials, this study investigates the potential for reducing the concentration of macrocomponents during the initial stages of the processing workflow. Chemical analysis of brines from various oil and gas fields in the Irkutsk region revealed their high mineralization, driven by the presence of calcium, magnesium, potassium, and sodium chlorides, alongside significant concentrations of microcomponents such as lithium (Li) and strontium (Sr). The phase composition of the raw underground brines, primarily consisting of tachyhydrite and sinjarite, was examined, along with post-precipitation product samples, which contained substantial amounts of strontium chloride hydrate. The study demonstrates the feasibility of separating brine components by transferring the majority of calcium, potassium, and iron into the precipitate. The parameters influencing the precipitation process and their effect on the quality of the resulting products were established. Subsequent sorption extraction of lithium and ion-exchange purification of the primary lithium concentrate enabled the production of a lithium-containing product with minimal impurities, achieving over 86 % lithium recovery. As a result, the concentration of major macrocomponents in the primary lithium concentrate was significantly reduced compared to the original brine: calcium to 0.18 % by weight, potassium to 15 % by weight, magnesium to 0.19 % by weight, and iron (II) to less than 0.02 % by weight.
- 5 March 2024
- Published by Springer Nature
- p. 539-548
Study of Primary Graphite Separation Products for the Creation of Petroleum Product Sorbents on Their Basis
- 5 March 2024
- Published by Springer Nature
- p. 539-548
Study of Primary Graphite Separation Products for the Creation of Petroleum Product Sorbents on Their Basis
- Open Access
- 30 December 2022
- Published by Nosov Magnitogorsk State Technical University in Subsurface Management and Transportation Systems
- Vol. 12 (2) , 46-52
Technological Solutions for Involving Sludge from Mining and Metallurgical Enterprises into Recycling
Тонкодисперсные шламы сооружений очистки отходящих газов и сточных вод горно-металлургических предприятий, с одной стороны, являются экологически опасными отходами, с другой – техногенным ресурсом металлов. В статье рассмотрены состав, структура, физические и химические свойства шламов предприятий черной и цветной металлургии. Шламы разделены авторами на две группы по обособленности фазы, содержащей ценный компонент, от других ингредиентов шлама. Такое разделение является важным для оценки пригодности шламов для разделительных процессов обогащения и выбора решений по подготовке данного вида тонкодисперсного техногенного сырья и его вовлечения в переработку с извлечением металлов. Описана современная практика утилизации шламов на предприятиях. Проанализированы существующие и предложены новые технологические решения, позволяющие вовлечь шламы в рециклинг металлов. Отмечено, что в некоторых случаях для эффективной утилизации шламов необходимо целенаправленное получение в многостадиальном процессе очистки вод селективных по металлу шламов. Представлены результаты изучения конкретных представителей выделенных групп шламов, результаты лабораторных испытаний по извлечению из них цветных металлов. Описаны разработанные технологические решения по комплексной переработке железоцинксодержащих доменных шламов ОАО «Магнитогорский металлургический комбинат» по комбинированной схеме, включающей обратную флотацию шламов и мокрую магнитную сепарацию. Представлены результаты использования, контролируемого по рН гидроксидного и сульфидного осаждения, а также схемы цементация-сульфидное осаждение для получения селективных медь- и цинксодержащих шламов при переработке подотвальной воды. Приведены технологические и экономические показатели переработки. Сформулированы принципы, на которых должны базироваться технологические решения ресурсосберегающих технологий переработки шламов.
- 30 December 2022
- Published by Nosov Magnitogorsk State Technical University in Subsurface Management and Transportation Systems
- Vol. 12 (2) , 46-52
Open AccessTechnological Solutions for Involving Sludge from Mining and Metallurgical Enterprises into Recycling
Тонкодисперсные шламы сооружений очистки отходящих газов и сточных вод горно-металлургических предприятий, с одной стороны, являются экологически опасными отходами, с другой – техногенным ресурсом металлов. В статье рассмотрены состав, структура, физические и химические свойства шламов предприятий черной и цветной металлургии. Шламы разделены авторами на две группы по обособленности фазы, содержащей ценный компонент, от других ингредиентов шлама. Такое разделение является важным для оценки пригодности шламов для разделительных процессов обогащения и выбора решений по подготовке данного вида тонкодисперсного техногенного сырья и его вовлечения в переработку с извлечением металлов. Описана современная практика утилизации шламов на предприятиях. Проанализированы существующие и предложены новые технологические решения, позволяющие вовлечь шламы в рециклинг металлов. Отмечено, что в некоторых случаях для эффективной утилизации шламов необходимо целенаправленное получение в многостадиальном процессе очистки вод селективных по металлу шламов. Представлены результаты изучения конкретных представителей выделенных групп шламов, результаты лабораторных испытаний по извлечению из них цветных металлов. Описаны разработанные технологические решения по комплексной переработке железоцинксодержащих доменных шламов ОАО «Магнитогорский металлургический комбинат» по комбинированной схеме, включающей обратную флотацию шламов и мокрую магнитную сепарацию. Представлены результаты использования, контролируемого по рН гидроксидного и сульфидного осаждения, а также схемы цементация-сульфидное осаждение для получения селективных медь- и цинксодержащих шламов при переработке подотвальной воды. Приведены технологические и экономические показатели переработки. Сформулированы принципы, на которых должны базироваться технологические решения ресурсосберегающих технологий переработки шламов.
- 29 November 2019
- Published by Ore and Metals Publishing House in Gornyi Zhurnal
- p. 37-43
Features of the Ural low-titanium magnetite ore processing
The article presents the results of technological research, which is the basis for the development of a scheme for the staged magnetic concentration of low-titanium magnetite ore from the Suroyamskoe deposit. The object of the research was technological samples of primary titanomagnetite ore with a mass fraction of total iron of 13.87% and titanomagnetite ore from the upper oxidized zone of the deposit, with a mass fraction of total iron of 10.97%. During laboratory tests, the material constitution, physical and mechanical properties, crushability, grindability and processibility of the samples by magnetic separation were determined. It is found that the material constitution of the ore sample from the oxidized zone features the increased mass fraction of aluminum oxide and silicon oxide, as well as the presence of sphene, which indicates the formation of clay minerals in the processes of natural weathering and dissociation of rocks. For primary titanomagnetite ore, the possibility of coarse dry magnetic separation of the initial ore with a particle size of –20 + 5 mm is found, which allows extraction of the magnetic fraction at the yield of 55.26% and the mass fraction of 20.8% Fe total at the recovery of 83.41%. For weathered oxidized titanomagnetite ore, washing is found to be expedient, which allows increasing the mass fraction of iron before wet magnetic separation by 2.1% at the iron extraction of 86.8% in washed ore and reduced mass fraction of titanium by 0.3%. According to the proposed technology of the staged magnetic separation, it is possible to extract a good-quality iron concentrate with iron mass fraction of 63.1% from the ledge ore of the of the Suroyamskoye deposit. The concentrate with a rather high mass fraction of iron of 58.2% can be obtained from the low-grade weathered oxidized ore. Simple circuits, structural arrangements and low costs of the proposed technologies for processing low-titanium ore from the Suroyamskoye deposit will allow production of iron concentrates suitable for use at metallurgical plants of the Chelyabinsk Region.
- 29 November 2019
- Published by Ore and Metals Publishing House in Gornyi Zhurnal
- p. 37-43
Features of the Ural low-titanium magnetite ore processing
The article presents the results of technological research, which is the basis for the development of a scheme for the staged magnetic concentration of low-titanium magnetite ore from the Suroyamskoe deposit. The object of the research was technological samples of primary titanomagnetite ore with a mass fraction of total iron of 13.87% and titanomagnetite ore from the upper oxidized zone of the deposit, with a mass fraction of total iron of 10.97%. During laboratory tests, the material constitution, physical and mechanical properties, crushability, grindability and processibility of the samples by magnetic separation were determined. It is found that the material constitution of the ore sample from the oxidized zone features the increased mass fraction of aluminum oxide and silicon oxide, as well as the presence of sphene, which indicates the formation of clay minerals in the processes of natural weathering and dissociation of rocks. For primary titanomagnetite ore, the possibility of coarse dry magnetic separation of the initial ore with a particle size of –20 + 5 mm is found, which allows extraction of the magnetic fraction at the yield of 55.26% and the mass fraction of 20.8% Fe total at the recovery of 83.41%. For weathered oxidized titanomagnetite ore, washing is found to be expedient, which allows increasing the mass fraction of iron before wet magnetic separation by 2.1% at the iron extraction of 86.8% in washed ore and reduced mass fraction of titanium by 0.3%. According to the proposed technology of the staged magnetic separation, it is possible to extract a good-quality iron concentrate with iron mass fraction of 63.1% from the ledge ore of the of the Suroyamskoye deposit. The concentrate with a rather high mass fraction of iron of 58.2% can be obtained from the low-grade weathered oxidized ore. Simple circuits, structural arrangements and low costs of the proposed technologies for processing low-titanium ore from the Suroyamskoye deposit will allow production of iron concentrates suitable for use at metallurgical plants of the Chelyabinsk Region.
- Open Access
- 14 December 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 451 (1) , 012227
Study of adsorption of cadmium on aluminosilicate sorbents
The research is aimed at developing the methods of reduction of the anthropogenic impact of cadmium on the hydrosphere of the mining region. To reduce the entry of cadmium into the hydrosphere, it is necessary to purify acidic mine waters and carry out the post- treatment of waste waters after lime treatment. For the post-treatment, the most practical is the method of sorption. Hollow glass microspheres, ceramic microspheres, metakaolin and microsilicon dioxide were studied as sorbents. Sorption isotherms are obtained and their mathematical description is made. The specific adsorption of cadmium varies from 0.58 to 0.12 mmol/g. The time to achieve sorption equilibrium in the sorbent-salt solution system is not less than 40 min. The most effective adsorption of cadmium is observed when using hollow glass microspheres. There is a potential use of hollow glass microspheres for the removal of cadmium from waste waters in the broad range of pH values.
- 14 December 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 451 (1) , 012227
Open AccessStudy of adsorption of cadmium on aluminosilicate sorbents
The research is aimed at developing the methods of reduction of the anthropogenic impact of cadmium on the hydrosphere of the mining region. To reduce the entry of cadmium into the hydrosphere, it is necessary to purify acidic mine waters and carry out the post- treatment of waste waters after lime treatment. For the post-treatment, the most practical is the method of sorption. Hollow glass microspheres, ceramic microspheres, metakaolin and microsilicon dioxide were studied as sorbents. Sorption isotherms are obtained and their mathematical description is made. The specific adsorption of cadmium varies from 0.58 to 0.12 mmol/g. The time to achieve sorption equilibrium in the sorbent-salt solution system is not less than 40 min. The most effective adsorption of cadmium is observed when using hollow glass microspheres. There is a potential use of hollow glass microspheres for the removal of cadmium from waste waters in the broad range of pH values.
- Open Access
- 1 January 2017
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 52 (1) , 012083
Selective recovery of copper and zinc from mine dump waters of mining enterprises in precipitates
The acid mine dump waters at mining companies that mining the copper and copperzinc sulphide ore have the high concentrates of metals and classified in our view as the raw materials for selective recovery of metals in precipitates comparable in quality with concentrates of ores enrichment and suitable for further metallurgical processing. Authors have implemented three two-stage schemes for sequential extraction of copper and zinc: cementation-sulphide precipitation, galvanocoagulation-sulphide precipitation, precipitation-precipitation. Moreover, parameters of processes and quality of the obtained precipitates have described. The achieved copper recovery is 89% and 94% respectively with the application of cementation and galvanocoagulation, in sulphide precipitate exceeded 75%. Furthermore, the copper recovery from decoppering in precipitates amounted to more than 65%. Zinc-containing precipitates because of coprecipitation of iron, magnesium and calcium contain zinc from 14% to 28%, in two to three times less than the quality of conditioned zinc concentrates. The content of precipitates allows to apply them for additional charging to concentrates of enrichment or for the production of metals in metallurgical treatment. As a result of the studying the effect of reduced total salinity (S) on mass fraction of zinc in precipitate (β) with the constant concentration of zinc (SZn), the changes in concentration with constant salinity and reduction in total salinity (S) with constant ratio S/CZn, the following dependencies have obtained: 0,{\left( {{{\partial \beta } \over {\partial S}}} \right)_{{C_{Zn}}}} < 0$" src="http://cdn.iopscience.com/images/1755-1315/52/1/012083/EES_52_1_012083_eqn_001.gif">, in the range of an index S from 4.5 to 90.0 g/L , where is a partial derivative of x to y, whereas the value z is fixed.
- 1 January 2017
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 52 (1) , 012083
Open AccessSelective recovery of copper and zinc from mine dump waters of mining enterprises in precipitates
The acid mine dump waters at mining companies that mining the copper and copperzinc sulphide ore have the high concentrates of metals and classified in our view as the raw materials for selective recovery of metals in precipitates comparable in quality with concentrates of ores enrichment and suitable for further metallurgical processing. Authors have implemented three two-stage schemes for sequential extraction of copper and zinc: cementation-sulphide precipitation, galvanocoagulation-sulphide precipitation, precipitation-precipitation. Moreover, parameters of processes and quality of the obtained precipitates have described. The achieved copper recovery is 89% and 94% respectively with the application of cementation and galvanocoagulation, in sulphide precipitate exceeded 75%. Furthermore, the copper recovery from decoppering in precipitates amounted to more than 65%. Zinc-containing precipitates because of coprecipitation of iron, magnesium and calcium contain zinc from 14% to 28%, in two to three times less than the quality of conditioned zinc concentrates. The content of precipitates allows to apply them for additional charging to concentrates of enrichment or for the production of metals in metallurgical treatment. As a result of the studying the effect of reduced total salinity (S) on mass fraction of zinc in precipitate (β) with the constant concentration of zinc (SZn), the changes in concentration with constant salinity and reduction in total salinity (S) with constant ratio S/CZn, the following dependencies have obtained: 0,{\left( {{{\partial \beta } \over {\partial S}}} \right)_{{C_{Zn}}}} < 0$" src="http://cdn.iopscience.com/images/1755-1315/52/1/012083/EES_52_1_012083_eqn_001.gif">, in the range of an index S from 4.5 to 90.0 g/L , where is a partial derivative of x to y, whereas the value z is fixed.
- 30 December 2016
- Published by Nosov Magnitogorsk State Technical University in Modern Problems of Russian Transport Complex
- Vol. 6 (1) , 4-18
The concept of a system for advanced training teachers in the field of the ecological education on the basis of logistics model of sustainable development
Концепция системы повышения квалификации преподавателей в области экологического образования на основе логистической модели устойчивого развития
- 30 December 2016
- Published by Nosov Magnitogorsk State Technical University in Modern Problems of Russian Transport Complex
- Vol. 6 (1) , 4-18
The concept of a system for advanced training teachers in the field of the ecological education on the basis of logistics model of sustainable development
Концепция системы повышения квалификации преподавателей в области экологического образования на основе логистической модели устойчивого развития
- Open Access
- 30 December 2016
- Published by Nosov Magnitogorsk State Technical University in Modern Problems of Russian Transport Complex
- Vol. 6 (1) , 29-33
The reduction of harmful impact of road transport in pick hours on air basin in the Magnitogorsk city
Снижение вредного воздействия автотранспорта в час пик на воздушный бассейн в городе Магнитогорске
- 30 December 2016
- Published by Nosov Magnitogorsk State Technical University in Modern Problems of Russian Transport Complex
- Vol. 6 (1) , 29-33
Open AccessThe reduction of harmful impact of road transport in pick hours on air basin in the Magnitogorsk city
Снижение вредного воздействия автотранспорта в час пик на воздушный бассейн в городе Магнитогорске