Raissa A. Queiroga
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Raissa A. Queiroga has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
- Antonio Gilson Barbosa de Lima
Department of Mechanical Engineering, Federal University of Campina Grande, Campina Grande 58429-900, Brazil
2 shared publications - Hortência L. F. Magalhães
Science and Technology Institute, Federal University of the Vales do Jequitinhonha e Mucuri, Diamantina 39100-000, Brazil
2 shared publications - Josiane Dantas Costa
Department of Mechanical Engineering, Federal University of Campina Grande, Campina Grande, Brazil
2 shared publications - José M. A. M. Gurgel
Postgraduate Program in Mechanical Engineering, Federal University of Paraiba, João Pessoa 58051-900, PB, Brazil
2 shared publications - Kelly Cristiane Gomes
Federal University of Paraíba
2 shared publications - Laís B. Alves
Dexco S.A., João Pessoa 58082-797, PR, Brazil
2 shared publications
Latest Publications
- Open Access
The Effect of Air Relative Humidity on the Drying Process of Sanitary Ware at Low Temperature: An Experimental Study
Drying is a thermodynamic process in which the moisture contained in the solid is removed by evaporation through the supply of an appreciable amount of thermal energy. It is recognized as a critical and intricate stage in the manufacturing process of ceramic materials. In general, drying at higher temperatures and lower air-relative humidity provokes severe hydric, thermal, and mechanical fractures in the ceramic parts, thus reducing product quality after the process. Then, this process must be realized under controlled conditions. From an industrial point of view, the drying process of sanitary ware takes place in two stages: drying at low temperatures (less than 40 °C) and drying at high temperatures (above 50 °C). Thus, the purpose of this work is to experimentally investigate the drying process at low temperatures in sanitary toilets. Drying experiments were conducted in an oven with the same temperature (35 °C) and different relative humidity of the drying air. The results of the moisture content, temperature, and dimension variations along the process, as well as drying and heating rates, are reported and analyzed. The results indicate that the higher the air’s relative humidity, the slower the moisture removal. Herein, aspects of the product quality after the drying process are also discussed.
Open AccessThe Effect of Air Relative Humidity on the Drying Process of Sanitary Ware at Low Temperature: An Experimental Study
Drying is a thermodynamic process in which the moisture contained in the solid is removed by evaporation through the supply of an appreciable amount of thermal energy. It is recognized as a critical and intricate stage in the manufacturing process of ceramic materials. In general, drying at higher temperatures and lower air-relative humidity provokes severe hydric, thermal, and mechanical fractures in the ceramic parts, thus reducing product quality after the process. Then, this process must be realized under controlled conditions. From an industrial point of view, the drying process of sanitary ware takes place in two stages: drying at low temperatures (less than 40 °C) and drying at high temperatures (above 50 °C). Thus, the purpose of this work is to experimentally investigate the drying process at low temperatures in sanitary toilets. Drying experiments were conducted in an oven with the same temperature (35 °C) and different relative humidity of the drying air. The results of the moisture content, temperature, and dimension variations along the process, as well as drying and heating rates, are reported and analyzed. The results indicate that the higher the air’s relative humidity, the slower the moisture removal. Herein, aspects of the product quality after the drying process are also discussed.
- Open Access
Investigating the Drying Process of Ceramic Sanitary Ware at Low Temperature
Drying is one of the stages with the highest energy consumption in the manufacturing process of ceramic materials and aims to reduce the product’s moisture to levels necessary for safe firing stage, reducing the chances of defect formation. For sanitary ware, there is an additional energy cost in the pre-drying stage, which takes place immediately after removing the parts from the molds, and is carried out in an environment with lower temperatures (ranging from 30 to 40 °C). This work aims to experimentally study the drying process of sanitary ware at low temperatures, with particular reference to sanitary toilets with industrial dimensions. Four drying experiments were carried out in an oven with different operating conditions (temperature and relative humidity). The results indicate that an increase in temperature and reduction in relative humidity provoke a faster drying rate. For some physical situations, it is more interesting to dedicate efforts to reducing the relative humidity of the drying air instead of seeking solutions to raise its temperature. Furthermore, a correlation between the linear retraction and moisture content was observed; the greater the moisture loss, the greater the sample shrinkage.
Open AccessInvestigating the Drying Process of Ceramic Sanitary Ware at Low Temperature
Drying is one of the stages with the highest energy consumption in the manufacturing process of ceramic materials and aims to reduce the product’s moisture to levels necessary for safe firing stage, reducing the chances of defect formation. For sanitary ware, there is an additional energy cost in the pre-drying stage, which takes place immediately after removing the parts from the molds, and is carried out in an environment with lower temperatures (ranging from 30 to 40 °C). This work aims to experimentally study the drying process of sanitary ware at low temperatures, with particular reference to sanitary toilets with industrial dimensions. Four drying experiments were carried out in an oven with different operating conditions (temperature and relative humidity). The results indicate that an increase in temperature and reduction in relative humidity provoke a faster drying rate. For some physical situations, it is more interesting to dedicate efforts to reducing the relative humidity of the drying air instead of seeking solutions to raise its temperature. Furthermore, a correlation between the linear retraction and moisture content was observed; the greater the moisture loss, the greater the sample shrinkage.
- 1 January 2019
- Published by Elsevier in Materials Today: Proceedings
- Vol. 14, 671-677
Electrochemical Characterization of a Welded Joint of NiTi/TiMo Dissimilar Wires
- 1 January 2019
- Published by Elsevier in Materials Today: Proceedings
- Vol. 14, 671-677
Electrochemical Characterization of a Welded Joint of NiTi/TiMo Dissimilar Wires