OIOmer Adam Omer Ishag

Omer Adam Omer Ishag

*This is an algorithmically generated author record based on publicly available information.

Omer Adam Omer Ishag has a total of 38 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Production of Biodiesel from Waste Cooking Oil Using KOH/Al2O3 as a Heterogeneous Catalyst

    by Ibrahim Yaagoub Erwa, Asmo Hassan, Razan Sali̇m, Omer Ishag, Maysoon Ahmed

    The catalytic performance of potassium hydroxide supported on alumina (KOH/Al2O3) for transesterification of waste cooking oil (WCO) was investigated. XRD, FTIR, and SEM techniques were used to characterize the catalyst after it had been synthesized using the wet impregnation method. The properties of the WCO and the produced biodiesel were evaluated. The main fatty acids of WCO were linoleic (45.61%), elaidic (33.86%), palmitic (10.32%), and stearic acid (4.80%), the acid value (2.29 mg KOH/g), FFA (1.15%), density at 25 °C (0.91 g/cm3), viscosity at 40 °C (34.09 mm2/s), water content (0.0017%), and flash point (206 °C). The XRD pattern of the catalyst showed diffraction peaks of KAlO2 attributed to the orthorhombic crystal system having a 12.46% degree of crystallinity. The SEM micrographs confirmed the amorphous nature of the catalyst. The presence of K–O and Al–O bonds in the catalyst was confirmed by the FTIR. A biodiesel yield of 86.6% was achieved with the following variables: oil to methanol ratio of 1:4, catalyst loading of 1.5% (w/v%), reaction temperature of 55 °C, and a reaction time of 1 h. The results appeared to show a decreasing pattern of yield after 4 cycles of reaction from 86.60 to 51.50%. The fuel properties were density (0.8919 g/cm3), viscosity (7.428 cSt), flash point (65 °C), acid number (0.54 mg KOH/g) and water content (0.0196%). Furthermore, the properties of the prepared biodiesel have been found to comply with the ASTM and EN standard specifications. This catalyst showed promising results for manufacturing biodiesel from low-cost feedstock.


  • Open Access

    Chemical Composition and Repellent Activity of Methyl Cinnamate-Rich Basil (Ocimum basilicum) Essential Oil

    by Azhari H. Nour, Abeer A İdri̇s, Omer Ishag, Abdurahman Nour

    Basil (Ocimum basilicum L.) is an important culinary herb and essential oil source widely recognized worldwide. The oil of the plant is beneficial for medicinal uses, and it has many biological activities such as insect repellent, larvicidal, and bactericidal. This study aimed to investigate basil's essential oil for its chemical composition and repellent activity. The essential oil of basil was extracted from fresh leaves by steam distillation method, and the chemical composition of the oil was determined by using GC/MS. Also, the repellent activity of the oil was tested against American cockroaches. Ebeling Choice-Box test with a little modification used in repellence test. The obtained results of chemical composition revealed that the amount of the oil contained forty-one chemical constituents (~97.1%); the major constituents were methyl cinnamate (25.3%), linalool (19.1%) and estragole (12.3%) as the major oxygenated monoterpenes. While α-bergamoten (5.3%), germacrene (4.6%), γ-cadinene (2.8%), and β-elemene (2.4%) were the main compounds in sesquiterpene hydrocarbons. Whereas, in oxygenated sesquiterpenes, Tau-cadinol (4.3%) was an important compounds and ocimene the highest compound in monoterpene hydrocarbons. The obtained results also indicated that the essential oil had good activity against the P. American, at a 100% concentration of oil; the repellence reaches 100% after 1 h. The IC50 and IC90 values of basil essential oil against P. Americans were 53.0 and 83.0%, respectively. The major compound methyl cinnamate which exists in basil essential oil is a very important compound and could be used in a wide area of industrial applications as repellent products, medicinal products, and cosmetics.


  • Open Access

    Nonlinear Fitting for Estimation of Adsorption Equilibrium, Kinetic and Thermodynamic Parameters of Methylene Blue onto Activated Carbon

    by Ibrahim Yaagoub Erwa, Omer Ishag, Omar Alrefaei̇, Issa Hassan

    Adsorption equilibrium, kinetics, and thermodynamics of methylene blue dye (MB) from aqueous solutions onto activated carbon (AC) synthesized from pomegranate peel was conducted in controlled batch systems. The effects of initial MB concentration, AC particle size, contact time, and temperature on adsorption were evaluated. Under the optimized conditions (i.e., contact time 120 min, pH ∼ 5, particle size 125 µm, dye concentration 20 mg/L, temperature 333 K, and 0.5 g AC/50 mL MB solution), the removal percentages can achieve ∼ 98.28%. The nonlinear method was conducted for estimating the equilibrium and kinetic parameters, where the equilibrium data were fitted to the Langmuir isotherm model. The Langmuir isotherm suggested a maximum monolayer adsorption capacity of 5.03 mg/g at 60 °C. The pseudo-second-order kinetic model provided the best fit to the experimental data compared with the pseudo-first-order. Kinetic studies showed that the adsorption equilibrium was rapidly established, with low activation energy entailed for adsorption (Ea; 15.60 kJ/mol). Thermodynamic parameters showed that the adsorption was spontaneous (−∆G° and +∆S°), exothermic (+∆H°), and favorable at ambient conditions.


  • Open Access

    Physicochemical Properties and Fatty Acids Composition of Sudanese Moringa Oleifera Seed Oil

    by Abeer A. Idris, Omer Ishag, Mahmoud M. Ali̇, Ibrahim Y. Erwa, Abdurahman H. Nour

    Moringa oleifera is a robust and fast growing tree considered as one of the most beneficial trees worldwide since almost all parts of it used as food, medicines and for industrial purposes. The aim of this study was to investigate the physicochemical properties and fatty acid composition of M. oleifera seed oil. The oil was extracted by Soxhlet using n-hexane; the physicochemical properties of the seed oil were assessed by standard and established methods, as well the fatty acid composition of the seed oil was determined by GC-MS. The golden yellow with characteristic odor oil obtained from the seeds had the following physicochemical properties: yield, 42.87%; freezing point, 0 °C; melting point, 21 °C; boiling point, 225 °C; refractive index (25 °C), 1.447; iodine value, 96.6 g/100g of oil; peroxide value, 7.6 meq.O2/kg of oil; free fatty acids, 0.07%; acid value, 1.4 mg of KOH/g of oil; saponification value, 185.2 mg KOH/g of oil; unsaponifiable matter, 3.2; moisture and volatile value, 4.91 (wt.%); density, 0.900 g/cm3; viscosity, 60.99 mm2/s; specific gravity, 0.907. The fatty acids composition showed that oleic- acid (51.74%) was the major fatty acid and followed by behenic- (10.54%), palmitic- (9.20%), stearic- (8.46%), arachidic- (6.41%), gondic- (4.88%), lignoceric- (3.08%) and palmitoleic acid (2.85%). Therefore, more and advanced research should be undertaken for this abundant source of natural oil for edible oil and possible industrial applications.


  • Open Access

    Phytochemical Screening, Chemical Composition and Antimicrobial Activity of Cinnamon verum Bark

    by Hamza Mohamed Ahmed, Ashraf Mahmoud Ramadhani, Ibrahim Yaagoub Erwa, Omer Adam Omer Ishag, Mohamed Bosharh Saeed

    Cinnamon dating from 1000 AD when it was firstly recorded in English due to its important as aroma and as herbs. The aim of this study was to investigate phytochemicals constitutes, chemical composition and antimicrobial activity of the essential oil of commercial samples of Cinnamon verum bark. The essential oil was extracted by hydrodistillation, while the crude extracts were prepared by three different solvents methanol (70%), acetone and aqueous. Phytochemical screening of crude extracts was performed using standard methods. The essential oil was subjected to GC-MS analysis and tested against Staphylococcus aureus, Salmonella typhimurium, Pseudomonas aeruginosa, Eschericchia coli and Candida albicans. The obtained results indicated the presence of alkaloids, flavonoids, coumarin, tannins, terpenoids, saponin, glycoside, anthrocyanin and phenolic compounds in the methanolic, aqoueous and acetone extracts of C. verum bark; while the major components of the extracted essential oil of C. verum bark were cinnamaldehyde (85.50%), stigmasterol (3.69%), Cadinene (1.37%), (E)-cinnamaldehyde (1.35%), alpha-amorphene (1.33%), hydrocinnamaldehyde (1.28%), alpha-cubebene (1.25) and ergosterol (1.09%) respectively. The antimicrobial activity result indicated the high activity of the extracted essential oil against all tested microorganisms at high concentration; except in S. typhimurium and C. albicans at concentrations of 25% and 12.5% no activity was noticed. Based in our obtained results the essential oil of C. verum bark had high potential as antimicrobial agent, therefore, recommended for more advanced studies to be conducted on this abundant plant as natural source of antibiotics.


  • Alkali-catalyzed Transesterification of Hibiscus sabdariffa (Roselle) Seed Oil for Biodiesel Production

    by Eman H. Ahmed, Azhari H. Nour, Omer A. Omer Ishag, Abdurahman H. Nour

    The need of energy never comes to an end so; the challenge is to procure power source sufficient to offer for our energy needs. Besides, this energy source must be dependable, renewable, recurring and non-contributing to climate change. Aims: This study was aimed to produce biodiesel from Roselle seed oil and to investigate its quality. Methodology: The Roselle seeds were clean from dirt, milled to proper size and the oil was extracted using soxhlet with n-hexane as solvent. The extracted oil was subjected to physiochemical analysis tests and then transesterified using methanol and potassium hydroxide as catalyst; with ratio of oil to alcohol 1:8 at 65°C. The quality of produced biodiesel was investigated and compared to international standards. The fatty acid composition of the produced biodiesel was determined by GC-MS. Results: Based on the experimental results, the yellow with characteristic odor oil was obtained from the seeds had the following physicochemical properties: yield, 12.65%; refractive index (25°C), 1.467 m ; free fatty acids, 5.5%; saponification value, 252 mg KOH/g of oil; density, 0.915 g/mL and ester value, 241 mgKOH/g. Also the biodiesel yield achieved was 96%, with density, 0.80 g/mL; API, 44.63; Kinematics viscosity @ 40˚C, 0.742; Pour point, < -51˚C; and Micro Carbon Residual (MCR), 0.65%; which conformed to the range of ASTM D6751 and EN 14214 standard specifications. However, the GC-MS analysis result revealed that the biodiesel produced was methyl ester and free other undesired products such as linoleic acid (33%), elaidic acid (29%) and palmitic acid (17%) and other biomolecules. Conclusion: Based on the obtained results, Roselle seed oil had potential for biodiesel production due to its high contains of free fatty acids. Therefore, in the future, more investigations in alcohol: oil ratio and the concentration of catalyst may be warranted to increase the yield much more.


  • Open Access

    Physicochemical properties and fatty acids composition of Sudanese Baobab (Adansonia Digitata L.) Seed oil

    by A. Idris Abeer, H. Nour Azhari, M. Ali Mahmoud, Y. Erwa Ibrahim, A. Omer Ishag Omer

    Baobab (Adansonia digitata) is a widespread tree species of the genus Adansonia, native to the African continent. The tree has multi-purpose uses, as it produces food and non-food products such as medicines and fuel. The global demand for baobab raw material for industrial applications has increased dramatically in recent years, thereby increasing their commercial value and importance. The aim of this study was to characterize the physicochemical properties and fatty acid composition of A. digitata seed oil. The oil is extracted by Soxhlet using n-hexane. The physicochemical properties of the seed oil were assessed by standard and established methods. The fatty acid composition of the seed oil was determined by GC-MS. The reddish yellow with characteristic odor oil obtained from the seeds had the following physicochemical properties: yield, 33.83%; melting point, 8 °C; boiling point, 227 °C; refractive index (25 °C), 1.436; iodine value, 98.3 g/100 g of oil; peroxide value, 4.3 meq. O2/kg of oil; free fatty acids, 0.34%; acid value, 6.8 mg of KOH/g of oil; saponification value, 180.7 mg KOH/g of oil; unsaponifiable matter, 1.7; moisture and volatile value, 14.79 (wt%); density, 0.867 g/cm3; viscosity, 35.03 mm2/s; specific gravity, 0.874. The fatty acids composition showed that linoleic acid (30.63%) was the major fatty acid and followed by oleic- (23.34%), palmitic- (22.87%), stearic- (5.89%), malvalic- (5.52%), cis-10-nonadecenoic- (2.67%), sterculic- (1.61%) and arachidic acid (1.43%). Therefore, more and advanced research should be undertaken for this abundant source of natural oil for possible industrial applications.


  • Proximate Composition, Physicochemical Properties and Antioxidant Activity of Flaxseed

    by Omer Adam Omer Ishag, Ayat A. Khalid, Amina Abdi, Ibrahim Yaagoub Erwa, Awadalla Babiker Omer, Azhari H. Nour

    Aims: The aims of this study were to investigate the proximate composition of flaxseed; physiochemical properties and antioxidant activity of flaxseed. Study Design: Using standard analytical methods to determine the proximate composition of flaxseed, extraction of flaxseed in different trials under the same conditions using two different solvents and investigating their physicochemical properties and antioxidant activity. Place and Duration of Study: This study was conducted in the laboratory of department of applied and industrial chemistry, International University of Africa, University of Medical Sciences and Technology and National Centre for Research, Khartoum – Sudan, during June 2019. Methodology: The prepared sample of flaxseeds was tested for proximate composition and then extracted with petroleum ether and n-hexane. The extracted oil was then subjected to physicochemical analysis, GC-MS analysis and antioxidant activity test. Results: The oil yield of flaxseed was high 21.95% and 28.29% with n-hexane and petroleum ether respectively. The results obtained for proximate composition were: moisture (8.50 ± 0.49%), ash (1.96 ± 0.00%), fiber (20.23 ± 3.47%), protein (21.00 ± 0.74%),fat (43.17 ± 0.99%) and carbohydrate (5.14 ± 2.73%).The physicochemical properties of n-hexane and petroleum ether extracted flaxseed oils were: density (0.92 ± 0.00 g/cm3), refractive index (1.47 ± 0.00 and 1.48 ± 0.01 at 28°C), acid value (0.76 ± 0.10 and 0.75 ± 0.20 mg KOH/g), peroxide value (4.67 ± 1.00 and 2.69 ± 0.55 meq O2/kg), saponification value (185.61 ± 0.56 and 187.83 ± 2.08 mg KOH/g oil), unsaponifiable matter (5.57 ± 0.64 and 2.83 ± 0.23 mg KOH/g oil) and iodine value (97.24 ± 0.86 and 97.44 ± 2.93 g/100 g) respectively. Statistical analysis showed no significant difference between the means of the two data sets of physicochemical properties of flaxseed oils extracted with the two solvents used at 95% confidence level. The GC-MS spectrum of flaxseed oil extracted with n-Hexane revealed presence of 27 fatty acids, the predominant were linoleic acid (46.53%), palmitic acid (18.04%), stearic acid (12.23%), linolenic acid (11.63%) and oleic acid (4.24%). While for petroleum ether extract a total of 28 fatty acids were identified the major were: linolenic acid (42.39%), linoleic acid (26.17%), palmitic acid (12.89%), stearic acid (10.73%) and methyl erucic (1.24%.). The oils also, showed good antioxidant activity in relation to control; 28 ± 0.09 (DPPH) for n-Hexane extract and 26 ± 0.05 (DPPH) for petroleum ether extract. Conclusion: Based on the results obtained flaxseed and flaxseed oil had good potential for human consumption and can be used for other application.


  • Open Access

    Physicochemical Properties and Fatty Acid Composition of Ocimum basilicum L. Seed Oil

    by Abeer A. Idris, Mahmoud M. Ali, Ibrahim Y. Erwa, Omer A. Omer Ishag, Abdurahman H. Nour

    Ocimum basilicum has been widely used in traditional medicine. Rural communities have used fixed oils for variety purposes since a long time ago. They used for cosmetic applications, fuel, medicine and food. The aim of this study was to characterize the physicochemical properties and fatty acid composition of O. basilicum seed oil. Lipids were determined by continuous extraction in a Soxhlet apparatus for 6 hours using hexane as solvent. The physicochemical properties of the oil were assessed by standard and established methods. The fatty acids composition of the seed oil was determined by GC-MS. The Pale yellow with camphor odor oil extracted from the seed has the following properties: yield, 18.01%; freezing point, -2°C; melting point, 5°C; boiling point, 215°C; refractive index (25°C), 1.48532; iodine value, 108.6 g/100 g of oil; peroxide value, 4.6 meq. O2/kg of oil; free fatty acids, 0.20%; acid value, 4.0 mg of KOH/g of oil; saponification value, 164.2 mg KOH/g of oil; unsaponifiable matter, 1.6; moisture and volatile value, 4.97 (wt%); density, 0.91372 g/cm3; viscosity, 10.29 mm2/s; specific gravity, 0.9210. Fatty acids composition showed that linolenic- (43.92%) was the major fatty acid and followed by linoleic- (32.18%), palmitic- (13.38%), stearic- (6.55%), palmitoleic- (0.78%), arachidic- (0.72%), anteisomargaric- (0.45%), nonadecylic- (0.28%), gondoic- (0.27%), margaric- (0.20%), behenic- (0.17%), heneicosylic- (0.14%), lignoceric- (0.13%) and myristic acid (0.11%). Therefore, recommended that more and advanced investigations should be undertaken for this abundant oil as natural source for many industrial applications, especially, for applications that require acids like linolenic and linoleic.


  • Open Access

    Extraction, Physicochemical Characteristics and Fatty Acids Profile of Kernel Oil from Mangifera indica L. Cultivated in Sudan

    by Ibrahim Yaagoub Erwa, Frank Starch Matenje, Yusuf Mnenula Mwachumu, Omer Adam Omer Ishag, Hamza Mohamed Ahmed

    Aims: This study was aimed to investigate the physicochemical properties and fatty acids composition of Mangifera indica L. seed kernel oil; in addition to investigating the effect of solvent type and extraction duration on extracts properties. Study Design: Extraction of Mangifera indica L. seed kernel oil in different trials under the same conditions using two different solvents for different time of extraction, and determining their physicochemical properties and fatty acids constituents. Place and Duration of Study: This study was conducted at the Department of Applied and Industrial chemistry International University of Africa (IUA), Khartoum, Sudan, between July and November 2019. Methodology: The oil from Mangifera indica L. seed kernel was extracted using n-hexane and petroleum ether in a soxhlet apparatus for 4 and 7 h. the physicochemical properties of the extracted oils were determined using standard official methods. Fatty acid profile of n-hexane extract was identified by gas chromatography/mass spectrometer (GC/MS) after methylation. Results: n-Hexane exhibits better extraction efficiency (11.40±0.66% for 7 h) than petroleum ether (10.80±0.44% for 7 h). The density and refractive index of the oil were 0.89±0.01 g/cm3 and 1.46 ± 0.01 at 28ºC respectively. The physicochemical properties of n-Hexane and petroleum ether extracts were acid value (3.35±0.54 and 2.52±0.13 mg KOH/g oil), peroxide value (4.32±0.65 and 5.11±1.03 meq O2/kg), saponification value (201.05±0.95 and 198.66±1.04 mg KOH/g oil), ester value (197.59±0.67 and 192.54±0.20 mg KOH/g oil) respectively. The statistical analysis of obtained data revealed no significant difference, at 95% confidence interval, between the standard deviation and the mean of two data sets of physicochemical properties of Mangifera indica L. seed kernel oils extracted with the two solvents used. GC/MS analysis revealed a total of 18 fatty acids were identified in which the majors are stearic acid (39.79%), oleic acid (36.77%), palmitic acid (10.34%), linoleic acid (6.02%) and eicosanoic acid (3.83%). Conclusion: The results suggest that mango seed kernel contains stable oil which can be potentially extracted by n-hexane; however, the solvent type has no significant effect on the physicochemical properties of the extracted oil and has the potential usefulness to be used in soap industry.