Dudekula Althaf Basha
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Dudekula Althaf Basha has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
Hidetoshi Somekawa
6 shared publications- Alok Singh
Research Center for Structural Materials, National Institute for Materials Science, Tsukuba, Japan
4 shared publications - Koichi Tsuchiya
Research Center for Structural Materials, National Institute for Materials Science, Tsukuba, Japan
3 shared publications Alok Singh
2 shared publications- Julian M. Rosalie
Department of Materials Engineering Bundesanstalt für Materialforschung und ‐prüfung Unter den Eichen 87 12205 Berlin Germany
2 shared publications - Hiroyuki Watanabe
Osaka Res Inst Ind Sci & Technol, Morinomiya Ctr, Res Div Mat Sci & Engn, Joto Ku, 1-6-50 Morinomiya, Osaka 5368553, Japan
1 shared publication
Latest Publications
- 21 December 2025
- Published by Wiley in Advanced Engineering Materials
- Vol. 28 (4)
Deformation Behavior of Mg‐0.4Bi‐0.4Sn Alloy under Compression at Room Temperature
This study investigates the deformation behavior, texture characteristics, and dislocation structures of an Mg‐0.4 Bi‐0.4Sn alloy subjected to 3% compression. The electron backscatter diffraction imaging reveals the formation of {} twin, in addition to the typical tension, compression, and double twins observed in magnesium alloy. The strain‐to‐failure of the alloy is found to be an impressive 20.9% which can be due to the spread in texture intensity, activation of various types of twins, and slip systems. When further transmission electron microscopy investigations are carried out to explore the fundamental deformation mechanisms responsible for the plasticity of the alloy, the transmutation of matrix < a > type dislocations into < c + a > type dislocations at the {} twin boundary is observed. These < c + a > dislocations formed dipoles by encasing stacking faults present on the basal planes within the {} twin domain. Additionally, the cross slip of < a > and < c > type dislocations and the formation of pure edge and screw type < c > dislocations near the grain boundary are observed. Quasi‐in situ imaging and slip trace analysis at various strain levels indicate that basal < a > and pyramidal < c + a > slip systems are primarily activated during deformation.
- 21 December 2025
- Published by Wiley in Advanced Engineering Materials
- Vol. 28 (4)
Deformation Behavior of Mg‐0.4Bi‐0.4Sn Alloy under Compression at Room Temperature
This study investigates the deformation behavior, texture characteristics, and dislocation structures of an Mg‐0.4 Bi‐0.4Sn alloy subjected to 3% compression. The electron backscatter diffraction imaging reveals the formation of {} twin, in addition to the typical tension, compression, and double twins observed in magnesium alloy. The strain‐to‐failure of the alloy is found to be an impressive 20.9% which can be due to the spread in texture intensity, activation of various types of twins, and slip systems. When further transmission electron microscopy investigations are carried out to explore the fundamental deformation mechanisms responsible for the plasticity of the alloy, the transmutation of matrix < a > type dislocations into < c + a > type dislocations at the {} twin boundary is observed. These < c + a > dislocations formed dipoles by encasing stacking faults present on the basal planes within the {} twin domain. Additionally, the cross slip of < a > and < c > type dislocations and the formation of pure edge and screw type < c > dislocations near the grain boundary are observed. Quasi‐in situ imaging and slip trace analysis at various strain levels indicate that basal < a > and pyramidal < c + a > slip systems are primarily activated during deformation.
- 1 July 2018
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 730, 355-362
Room temperature grain boundary sliding behavior of fine-grained Mg-Mn alloys
- 1 July 2018
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 730, 355-362
Room temperature grain boundary sliding behavior of fine-grained Mg-Mn alloys
- 1 January 2018
- Published by Elsevier in Scripta Materialia
- Vol. 142, 50-54
Crack propagation along grain boundaries and twins in Mg and Mg–0.3 at.%Y alloy during in-situ straining in transmission electron microscope
- 1 January 2018
- Published by Elsevier in Scripta Materialia
- Vol. 142, 50-54
Crack propagation along grain boundaries and twins in Mg and Mg–0.3 at.%Y alloy during in-situ straining in transmission electron microscope
- 1 June 2017
- Published by Elsevier in Scripta Materialia
- Vol. 134, 80-84
Nucleation of recrystallized magnesium grains over quasicrystalline phase during severe plastic deformation of a Mg-Zn-Y alloy at room temperature
- 1 June 2017
- Published by Elsevier in Scripta Materialia
- Vol. 134, 80-84
Nucleation of recrystallized magnesium grains over quasicrystalline phase during severe plastic deformation of a Mg-Zn-Y alloy at room temperature
- 1 March 2017
- Published by Elsevier in Scripta Materialia
- Vol. 129, 35-38
Effect of twin boundary segregation on damping properties in magnesium alloy
- 1 March 2017
- Published by Elsevier in Scripta Materialia
- Vol. 129, 35-38
Effect of twin boundary segregation on damping properties in magnesium alloy
- 1 November 2016
- Published by Elsevier in Scripta Materialia
- Vol. 124, 169-173
Interfacial segregation induced by severe plastic deformation in a Mg–Zn–Y alloy
- 1 November 2016
- Published by Elsevier in Scripta Materialia
- Vol. 124, 169-173
Interfacial segregation induced by severe plastic deformation in a Mg–Zn–Y alloy
- Open Access
- 11 April 2016
- Published by Taylor & Francis in Science and Technology of Advanced Materials
- Vol. 17 (1) , 115-127
Microstructure study of a severely plastically deformed Mg-Zn-Y alloy by application of low angle annular dark field diffraction contrast imaging
Microstructural investigation of extremely strained samples, such as severely plastically deformed (SPD) materials, by using conventional transmission electron microscopy techniques is very challenging due to strong image contrast resulting from the high defect density. In this study, low angle annular dark field (LAADF) imaging mode of scanning transmission electron microscope (STEM) has been applied to study the microstructure of a Mg-3Zn-0.5Y (at%) alloy processed by high pressure torsion (HPT). LAADF imaging advantages for observation of twinning, grain fragmentation, nucleation of recrystallized grains and precipitation on second phase particles in the alloy processed by HPT are highlighted. By using STEM-LAADF imaging with a range of incident angles, various microstructural features have been imaged, such as nanoscale subgrain structure and recrystallization nucleation even from the thicker region of the highly strained matrix. It is shown that nucleation of recrystallized grains starts at a strain level of revolution (earlier than detected by conventional bright field imaging). Occurrence of recrystallization of grains by nucleating heterogeneously on quasicrystalline particles is also confirmed. Minimizing all strain effects by LAADF imaging facilitated grain size measurement of nm in fully recrystallized HPT specimen after . Graphical Abstract- 11 April 2016
- Published by Taylor & Francis in Science and Technology of Advanced Materials
- Vol. 17 (1) , 115-127
Open AccessMicrostructure study of a severely plastically deformed Mg-Zn-Y alloy by application of low angle annular dark field diffraction contrast imaging
Microstructural investigation of extremely strained samples, such as severely plastically deformed (SPD) materials, by using conventional transmission electron microscopy techniques is very challenging due to strong image contrast resulting from the high defect density. In this study, low angle annular dark field (LAADF) imaging mode of scanning transmission electron microscope (STEM) has been applied to study the microstructure of a Mg-3Zn-0.5Y (at%) alloy processed by high pressure torsion (HPT). LAADF imaging advantages for observation of twinning, grain fragmentation, nucleation of recrystallized grains and precipitation on second phase particles in the alloy processed by HPT are highlighted. By using STEM-LAADF imaging with a range of incident angles, various microstructural features have been imaged, such as nanoscale subgrain structure and recrystallization nucleation even from the thicker region of the highly strained matrix. It is shown that nucleation of recrystallized grains starts at a strain level of revolution (earlier than detected by conventional bright field imaging). Occurrence of recrystallization of grains by nucleating heterogeneously on quasicrystalline particles is also confirmed. Minimizing all strain effects by LAADF imaging facilitated grain size measurement of nm in fully recrystallized HPT specimen after . Graphical Abstract