JHJingxia Huang

Jingxia Huang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Jingxia Huang has a total of 8 co-authors. Here are the top co-authors by number of shared publications:

  • Feng Wang

    Department of Materials Science and Engineering & Shenzhen Engineering Research Center for Novel Electronic Information Materials and Devices South University of Science and Technology Shenzhen Guangdong 518055 China

    2 shared publications
  • Zehuan Wang

    Department of Materials Science and Engineering & Shenzhen Engineering Research Center for Novel Electronic Information Materials and Devices South University of Science and Technology Shenzhen Guangdong 518055 China

    2 shared publications
  • Hong Wang

    Department of Materials Science and Engineering & Shenzhen Engineering Research Center for Novel Electronic Information Materials and Devices South University of Science and Technology Shenzhen Guangdong 518055 China

    1 shared publication
  • Hong Wang

    Department of Materials Science and Engineering Southern University of Science and Technology Shenzhen China

    1 shared publication
  • Renchao Hu

    Department of Materials Science and Engineering & Shenzhen Engineering Research Center for Novel Electronic Information Materials and Devices South University of Science and Technology Shenzhen Guangdong 518 055 China

    1 shared publication
  • Xiaobin Tang

    State Key Laboratory of Mechanical Transmission Chongqing University Chongqing 400044 China

    1 shared publication

Latest Publications

  • Multi‐Hierarchical Microstructures Boosted Linearity of Flexible Capacitive Pressure Sensor

    by Jingxia Huang, Xiaobin Tang, Feng Wang, Zehuan Wang, Yujuan Niu, Hong Wang

    Besides the excellent sensitivity, linearity is also highly required for a miniaturization and low power consumption of the flexible sensor system. Herein, multi‐hierarchical microstructures to improve the linearity of capacitive pressure sensor based on poly(vinylidene fluoride)/reduced graphene oxide (PVDF/rGO) multilayer films is designed and constructed. The differentiated hierarchical microstructure in each layer comes from irregular protrusions with various roughness. Excellent sensor performances, such as higher sensitivity (0.18 kPa−1) in the linear range from 0.1 kPa to 11 kPa, lower limit of detection (100 Pa), rapid response time (56.3 ms) compared with some current reports, are obtained in the sensor based on three laminated films with the successive roughness (remarked as 150/400/800 Cw films). Moreover, the device exhibits outstanding stability over 3000 cycles at a pressure of 10 kPa, and successfully works on the falling leaf of 0.16 g and the weight of 100 g as well as high heel pressure. These outstanding properties are attributed to the compressibility of the hierarchical structure and efficient stress distribution between stacked multilayers, which is verified by using the finite‐element analysis (FEA). The work provides a simple and low‐cost route for fabricating high‐performance capacitive sensors with diverse potential applications in wearable electronics.


  • Adjusting Sensitivity and Linearity of the Wearable Pressure Sensors by an Arbitrary Micro‐Protuberance Structure of Polyvinylidene Fluoride/Reduced Graphene Oxide Dielectric Films

    by Jingxia Huang, Feng Wang, Xinwei Xu, Renchao Hu, Zehuan Wang, Hong Wang

    Flexible pressure sensors with high sensitivity over a broad linear range and fast response have extension applications in wearable electronics. Herein, we prepared a tunable capacitive pressure sensors based on arbitrary micro‐protuberances geometry films via low‐cost soft lithography, employing the polyvinylidene fluoride/reduced graphene oxide (PVDF/rGO) composite with a high dielectric constant of 172 and low loss tangent of 0.48. The hierarchical microstructures’ different sizes endow the sensors adjustable pressure response, achieving the regulation of sensitivity and linear detection range. The superior microstructured film‐based sensor exhibits a high sensitivity (1.19 kPa−1) over 20 times that of the bulk film, wide linearity (1.3 kPa), a rapid response (43 ms), a low limit of detection (10.6 Pa), and remarkable durability over 5000 compression/release cycles. In addition, based on the excellent sensing performance above‐mentioned, the device is successfully employed in the scenario of monitoring pressure interaction and human activities by mounting on different parts of the human body or object. This work provides a means to optimize the sensor's sensitivity and linearity by hierarchical structure and contributes to its wearable electronic applications.