Clizia Aversa
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Clizia Aversa has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Massimiliano Barletta
Dipartimento di Ingegneria Industriale, Elettronica e Meccanica, Università degli Studi Roma Tre, Roma, Italy
5 shared publications - Francesco Veniali
Dipartimento di Ingegneria Meccanica e Aerospaziale, Sapienza Università degli Studi di Roma, Rome, Italy
2 shared publications Nazan Koca
Dipartimento di Ingegneria Industriale, Elettronica e Meccanica Roma Tre University Rome Italy
2 shared publicationsA. Gisario
1 shared publication- A. Gisario
Sapienza Università di Roma, Dipartimento di Ingegneria Meccanica e Aerospaziale, Via Eudossiana 18, 001884 Roma (Italy)
1 shared publication - Annalisa Genovesi
Department of Industrial, Electronic and Mechanical Engineering, University of Roma Tre, 00146 Rome, Italy
1 shared publication
Latest Publications
- 28 August 2024
- Published by Springer Nature
- p. 360-367
Preparation and Characterizations of NiCrFeSiAlBC Coatings via a HVOF Process
- 28 August 2024
- Published by Springer Nature
- p. 360-367
Preparation and Characterizations of NiCrFeSiAlBC Coatings via a HVOF Process
- Open Access
- 5 September 2023
- Published by Materials Research Forum, LLC in Materials Research Proceedings
- Vol. 35
PET foaming: development of a new class of rheological additives for improved processability
PET foaming: development of a new class of rheological additives for improved processability Clizia Aversa, Massimiliano Barletta, Annalisa Genovesi, Annama
- 5 September 2023
- Published by Materials Research Forum, LLC in Materials Research Proceedings
- Vol. 35
Open AccessPET foaming: development of a new class of rheological additives for improved processability
PET foaming: development of a new class of rheological additives for improved processability Clizia Aversa, Massimiliano Barletta, Annalisa Genovesi, Annama
- 2 August 2023
- Published by Wiley in Polymer Engineering & Science
- Vol. 63 (10) , 3300-3312
Blown film extrusion of poly(lactic)acid/poly(3‐hydroxybutyrate‐4‐hydroxybutyrate) blends for improved toughness and processability
Poly(lactic acid) is one of the most commonly used bioplastics thanks to its mechanical performance and low environmental impact. Strategies to overcome excessive rigidity of PLA are constantly investigated. Poor viscoelastic behavior and brittleness of PLA seriously limit its potential application as a common film material. Herein highly amorphous Poly(3‐hydroxybutyrate‐4‐hydroxybutyrate) (P(3HB)(4HB)) was introduced to improve toughness and reduce brittleness of PLA. Anti‐blocking (silica) and anti‐slipping agent (Ethylene bis‐stearamide (EBS)) were added to improve the processability of the blends, specifically to solve winding issues of the blown film and unfolding of the layflat. In this study three formulations containing PLA and different ratios of P(3HB)(4HB), specifically 10–20–30% were extruded. The mechanical, thermal and surface characterization of the films was performed. The tensile and the tear strength test results show that P(3HB)(4HB) increased the ductility of PLA based films. Increasing amounts of P(3HB)(4HB) provide a toughening effect on PLA/P(3HB)(4HB) blown films without altering transparency of PLA. Moreover, the processing additives proved to be efficient in improving film blowing stability and avoiding tackiness during the winding phase of the film.
- 2 August 2023
- Published by Wiley in Polymer Engineering & Science
- Vol. 63 (10) , 3300-3312
Blown film extrusion of poly(lactic)acid/poly(3‐hydroxybutyrate‐4‐hydroxybutyrate) blends for improved toughness and processability
Poly(lactic acid) is one of the most commonly used bioplastics thanks to its mechanical performance and low environmental impact. Strategies to overcome excessive rigidity of PLA are constantly investigated. Poor viscoelastic behavior and brittleness of PLA seriously limit its potential application as a common film material. Herein highly amorphous Poly(3‐hydroxybutyrate‐4‐hydroxybutyrate) (P(3HB)(4HB)) was introduced to improve toughness and reduce brittleness of PLA. Anti‐blocking (silica) and anti‐slipping agent (Ethylene bis‐stearamide (EBS)) were added to improve the processability of the blends, specifically to solve winding issues of the blown film and unfolding of the layflat. In this study three formulations containing PLA and different ratios of P(3HB)(4HB), specifically 10–20–30% were extruded. The mechanical, thermal and surface characterization of the films was performed. The tensile and the tear strength test results show that P(3HB)(4HB) increased the ductility of PLA based films. Increasing amounts of P(3HB)(4HB) provide a toughening effect on PLA/P(3HB)(4HB) blown films without altering transparency of PLA. Moreover, the processing additives proved to be efficient in improving film blowing stability and avoiding tackiness during the winding phase of the film.
- 30 January 2023
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 140 (13)
Processing PLA/P(3HB)(4HB) blends for the manufacture of highly transparent, gas barrier and fully bio‐based films for compostable packaging applications
In this study, the extrusion process of PLA/P(3HB)(4HB) blends was studied and the effect on mechanical, thermal and physical properties of the blends containing increasing amounts of P(3HB)(4HB) was evaluated. The blends were prepared by means of a twin screw extruder and subsequently film samples were manufactured using a lab scale cast extruder. A potential industrial application of the studied materials was also validated by testing the films on a pilot thermoforming machine for the production of food containers. The extrusion process demonstrated good processability of blends containing 10%, 20%, and 30% of P(3HB)(4HB). Increasing the amount of P(3HB)(4HB) up to 40% and 50%, processability problems occurred related to tackiness of the materials both during extrusion compounding and during cast extrusion. Both granules and films were characterized and thermo‐physical and mechanical properties of the samples are hereinafter reported. The novel polymeric blends are found to be suitable for extrusion compounding, cast extrusion and thermoforming processes. Moreover, the blends exhibit enhanced performances in terms of flexibility and impact resistance as well as protection against gas permeation and boast exceptional transparency. Therefore, the innovative PLA/P(3HB)(4HB) blends prove to be suitable for the production of compostable single‐use packaging requiring high transparency and gas barrier.
- 30 January 2023
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 140 (13)
Processing PLA/P(3HB)(4HB) blends for the manufacture of highly transparent, gas barrier and fully bio‐based films for compostable packaging applications
In this study, the extrusion process of PLA/P(3HB)(4HB) blends was studied and the effect on mechanical, thermal and physical properties of the blends containing increasing amounts of P(3HB)(4HB) was evaluated. The blends were prepared by means of a twin screw extruder and subsequently film samples were manufactured using a lab scale cast extruder. A potential industrial application of the studied materials was also validated by testing the films on a pilot thermoforming machine for the production of food containers. The extrusion process demonstrated good processability of blends containing 10%, 20%, and 30% of P(3HB)(4HB). Increasing the amount of P(3HB)(4HB) up to 40% and 50%, processability problems occurred related to tackiness of the materials both during extrusion compounding and during cast extrusion. Both granules and films were characterized and thermo‐physical and mechanical properties of the samples are hereinafter reported. The novel polymeric blends are found to be suitable for extrusion compounding, cast extrusion and thermoforming processes. Moreover, the blends exhibit enhanced performances in terms of flexibility and impact resistance as well as protection against gas permeation and boast exceptional transparency. Therefore, the innovative PLA/P(3HB)(4HB) blends prove to be suitable for the production of compostable single‐use packaging requiring high transparency and gas barrier.
- Open Access
- 21 February 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 120 (3-4) , 2291-2309
Laser transmission welding of aluminum film coated with heat sealable co-polyester resin with polypropylene films for applications in food and drug packaging
The present work deals with the high-power diode laser joining process of aluminum films coated with a polyester resin with polypropylene (PP) films. The first part of the work focused on analyzing the coating process of aluminum films with a polyester resin, using an automatic applicator. The second part of the work was focused on the analysis of the laser joining process of coated aluminum films with plastic counterparts made of PP. Different thicknesses and colors of the PP parts were tested in order to analyze the joining process under a wide range of different conditions. The experimental plan involved the study of the influence of the laser joining parameters, in particular the scanning speed and beam power, on the joints. The joints between aluminum and PP films were subsequently tested by means of tensile and peel-off tests. All the joints between aluminum and PP are obtained through the so-called laser transmission welding (LTW) mechanism. Analysis of the mechanical response of the welded joints allowed to identify the optimal processing window, that is, the choice of the operational parameters that leads to satisfactory welded joints, stating the high potential of laser systems in the joining process of aluminum and PP films for food packaging applications.
- 21 February 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 120 (3-4) , 2291-2309
Open AccessLaser transmission welding of aluminum film coated with heat sealable co-polyester resin with polypropylene films for applications in food and drug packaging
The present work deals with the high-power diode laser joining process of aluminum films coated with a polyester resin with polypropylene (PP) films. The first part of the work focused on analyzing the coating process of aluminum films with a polyester resin, using an automatic applicator. The second part of the work was focused on the analysis of the laser joining process of coated aluminum films with plastic counterparts made of PP. Different thicknesses and colors of the PP parts were tested in order to analyze the joining process under a wide range of different conditions. The experimental plan involved the study of the influence of the laser joining parameters, in particular the scanning speed and beam power, on the joints. The joints between aluminum and PP films were subsequently tested by means of tensile and peel-off tests. All the joints between aluminum and PP are obtained through the so-called laser transmission welding (LTW) mechanism. Analysis of the mechanical response of the welded joints allowed to identify the optimal processing window, that is, the choice of the operational parameters that leads to satisfactory welded joints, stating the high potential of laser systems in the joining process of aluminum and PP films for food packaging applications.
- 1 October 2021
- Published by Elsevier in Optics & Laser Technology
- Vol. 142
Laser joining of aluminum film coated with vinylic resin and plastic/bioplastic films for applications in food packaging
- 1 October 2021
- Published by Elsevier in Optics & Laser Technology
- Vol. 142
Laser joining of aluminum film coated with vinylic resin and plastic/bioplastic films for applications in food packaging
- 1 August 2019
- Published by Elsevier in Polymer Testing
- Vol. 77, 105885
Extrusion blow molding of environmentally friendly bottles in biodegradable polyesters blends
- 1 August 2019
- Published by Elsevier in Polymer Testing
- Vol. 77, 105885
Extrusion blow molding of environmentally friendly bottles in biodegradable polyesters blends