Bernd Wittgens
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Bernd Wittgens has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
Alexander Wentzel
4 shared publicationsSidsel Markussen
4 shared publicationsCansu Birgen
3 shared publications- Sibashish Baksi
Department of Biotechnology School of Life Sciences Swami Vivekananda University 700121 Barrackpore West Bengal
3 shared publications Akash K. Ball
2 shared publications- Filippo Bisotti
SINTEF Industry, Department of Process Technology, Trondheim, Trøndelag, Norway
2 shared publications
Latest Publications
- 19 June 2026
- Published by The CACHE Foundation, Inc.
- Vol. 6, 2334-2339
Process design for the recovery of valuable organic compounds from pyrolysis oil aqueous phase
Pyrolysis, a key waste-to-X technology, enables converting a wide portfolio of biomass waste into valuable chemicals and fuels. However, raw pyrolysis oils are chemically and physically unstable. A multi-step stabilisation is necessary to reduce acidity and the content of reactive components, mainly carbonyls and carboxylic acids. During stabilisation, which involves deoxygenation and hydrogenation as the main steps, an aqueous phase is generated as a by-product. This stream contains mainly water, but relevant amounts of methanol and ethanol (2-8 wt%) are also present, together with minor concentrations of higher alcohols, C1-C4 carboxylic acids, and light esters. The aim of this work is to design and optimise a process to isolate the methanol and ethanol embodied in the aqueous phase and exploit them as intermediates to generate biofuels, biochemicals, and pharmaceutical products. The process consists of a train of four distillation columns to maximise the recovery rate and purity of the two targeted products. COCO-COFE, a CAPE-OPEN process simulator, is used for flowsheet development. The optimal number of theoretical stages and the optimal positioning of the feed to each unit have been optimised, considering a trade-off CAPEX-OPEX as the criterion. Results show that up to 95% and 98% yield can be achieved for methanol and ethanol, respectively. Methanol purity is limited to a maximum of 92 wt% due to the presence of volatile impurities, while ethanol contains residual propanol (6 wt%). The overall heat demand is in the order of 1 MJ/kg feed.
- 19 June 2026
- Published by The CACHE Foundation, Inc.
- Vol. 6, 2334-2339
Process design for the recovery of valuable organic compounds from pyrolysis oil aqueous phase
Pyrolysis, a key waste-to-X technology, enables converting a wide portfolio of biomass waste into valuable chemicals and fuels. However, raw pyrolysis oils are chemically and physically unstable. A multi-step stabilisation is necessary to reduce acidity and the content of reactive components, mainly carbonyls and carboxylic acids. During stabilisation, which involves deoxygenation and hydrogenation as the main steps, an aqueous phase is generated as a by-product. This stream contains mainly water, but relevant amounts of methanol and ethanol (2-8 wt%) are also present, together with minor concentrations of higher alcohols, C1-C4 carboxylic acids, and light esters. The aim of this work is to design and optimise a process to isolate the methanol and ethanol embodied in the aqueous phase and exploit them as intermediates to generate biofuels, biochemicals, and pharmaceutical products. The process consists of a train of four distillation columns to maximise the recovery rate and purity of the two targeted products. COCO-COFE, a CAPE-OPEN process simulator, is used for flowsheet development. The optimal number of theoretical stages and the optimal positioning of the feed to each unit have been optimised, considering a trade-off CAPEX-OPEX as the criterion. Results show that up to 95% and 98% yield can be achieved for methanol and ethanol, respectively. Methanol purity is limited to a maximum of 92 wt% due to the presence of volatile impurities, while ethanol contains residual propanol (6 wt%). The overall heat demand is in the order of 1 MJ/kg feed.
- 19 June 2026
- Published by The CACHE Foundation, Inc.
- Vol. 6, 1234-1241
Re-parametrisation of NRTL model for C1+ organics and alcohols recovery from aqueous phase in pyrolysis oil production
Pyrolysis is an emerging green pathway to produce bulk chemicals and sustainable fuels. However, pyrolysis oil requires stabilisation via hydrotreatment, and this process generates an aqueous waste containing alcohols (mainly methanol and ethanol), carboxylic acids, and some ketones. To increase the economic sustainability of biofuels production, there is increasing interest in recovering these valuable chemicals from water. Reliable thermodynamics are necessary to address the separation and design of equipment to fractionate such complex mixtures, with multiple azeotropes and non-idealities. The Non-Random Two-Liquids (NRTL) models in both Aspen Plus V12.0 and COFE V3.7, a license-free software released by AmsterChem, do not accurately reproduce the equilibrium measurements of most of the binary and ternary mixtures involving water, a C1-C4 alcohol, and a light carboxylic acid. This work aims to retune the activity-based model to improve the NRTL model predictivity, using experimental data retrieved from NIST ThermoData Engine V10.1. The regression is performed in Aspen Plus V12 using the Maximum Likelihood algorithm. The resulting re-parametrised NRTL shows improved accuracy and reliability compared to the existing models. For all investigated binary and ternary mixtures, the Average Relative Deviation (ARD) is lower than 20%, and for 75% of them, ARD is lower than 10%. The ARD in the prediction of vapour phase composition drops from 16.0% and 12.1% of the original COFE and Aspen Plus models, respectively, down to 7.0%.
- 19 June 2026
- Published by The CACHE Foundation, Inc.
- Vol. 6, 1234-1241
Re-parametrisation of NRTL model for C1+ organics and alcohols recovery from aqueous phase in pyrolysis oil production
Pyrolysis is an emerging green pathway to produce bulk chemicals and sustainable fuels. However, pyrolysis oil requires stabilisation via hydrotreatment, and this process generates an aqueous waste containing alcohols (mainly methanol and ethanol), carboxylic acids, and some ketones. To increase the economic sustainability of biofuels production, there is increasing interest in recovering these valuable chemicals from water. Reliable thermodynamics are necessary to address the separation and design of equipment to fractionate such complex mixtures, with multiple azeotropes and non-idealities. The Non-Random Two-Liquids (NRTL) models in both Aspen Plus V12.0 and COFE V3.7, a license-free software released by AmsterChem, do not accurately reproduce the equilibrium measurements of most of the binary and ternary mixtures involving water, a C1-C4 alcohol, and a light carboxylic acid. This work aims to retune the activity-based model to improve the NRTL model predictivity, using experimental data retrieved from NIST ThermoData Engine V10.1. The regression is performed in Aspen Plus V12 using the Maximum Likelihood algorithm. The resulting re-parametrised NRTL shows improved accuracy and reliability compared to the existing models. For all investigated binary and ternary mixtures, the Average Relative Deviation (ARD) is lower than 20%, and for 75% of them, ARD is lower than 10%. The ARD in the prediction of vapour phase composition drops from 16.0% and 12.1% of the original COFE and Aspen Plus models, respectively, down to 7.0%.
- Open Access
- 9 June 2025
- Published by Wiley in ChemSusChem
- Vol. 18 (14) , e202500741
Highly Concentrated Peroxodicarbonate for Efficient Oxidative Degradation of Kraft Lignin
The oxidative degradation of technically relevant types of Kraft lignin is efficiently accomplished by a significantly improved two‐step protocol. The key is the use of highly concentrated peroxodicarbonate solution which selectively oxidizes the lignin particles at moderate temperature which are thermally treated in a subsequent step. The liberation of low‐molecular‐weight phenols occurs when the oxidizer is already consumed enhancing the yield of target compounds strongly up to 15.6 wt%. Co‐generated carbonates in this transformation represent the make‐up chemical of pulping plants. This makes this approach suitable and attractive to be implemented as a bolt‐on or integrated into the Kraft pulping process. The green metrics clearly indicate the sustainable and superior features of the method established.
- 9 June 2025
- Published by Wiley in ChemSusChem
- Vol. 18 (14) , e202500741
Open AccessHighly Concentrated Peroxodicarbonate for Efficient Oxidative Degradation of Kraft Lignin
The oxidative degradation of technically relevant types of Kraft lignin is efficiently accomplished by a significantly improved two‐step protocol. The key is the use of highly concentrated peroxodicarbonate solution which selectively oxidizes the lignin particles at moderate temperature which are thermally treated in a subsequent step. The liberation of low‐molecular‐weight phenols occurs when the oxidizer is already consumed enhancing the yield of target compounds strongly up to 15.6 wt%. Co‐generated carbonates in this transformation represent the make‐up chemical of pulping plants. This makes this approach suitable and attractive to be implemented as a bolt‐on or integrated into the Kraft pulping process. The green metrics clearly indicate the sustainable and superior features of the method established.
- Open Access
- 17 June 2024
- Published by Royal Society of Chemistry (RSC) in Chemical Communications
- Vol. 60 (56) , 7136-7147
Peroxodicarbonate – a renaissance of an electrochemically generated green oxidizer
Peroxodicarbonate, accessible from direct anodic conversion of alkali carbonates, has experienced a renaissance in the past two decades. An overview of its history, synthesis, characteristics and reactivity is provided.
- 17 June 2024
- Published by Royal Society of Chemistry (RSC) in Chemical Communications
- Vol. 60 (56) , 7136-7147
Open AccessPeroxodicarbonate – a renaissance of an electrochemically generated green oxidizer
Peroxodicarbonate, accessible from direct anodic conversion of alkali carbonates, has experienced a renaissance in the past two decades. An overview of its history, synthesis, characteristics and reactivity is provided.
- 2 February 2018
- Published by Taylor & Francis in Journal of Natural Fibers
- Vol. 16 (5) , 662-676
Valorization of Lignocellulosic Waste (Crotalariajuncea) Using Alkaline Peroxide Pretreatment under Different Process Conditions: An Optimization Study on Separation of Lignin, Cellulose, and Hemicellulose
Lignocellulose materials, essentially consisting of lignin, cellulose and hemicelluloses, are abundant sources of fermentable sugars. The bast fiber of Crotalaria juncea (Sunn hemp), a native cover crop of India, was used as feedstock for this study. The primary objective of this study was to add value to the waste C. juncea bast fiber. The same was achieved by pretreating the waste fiber using alkaline peroxide solution at various process conditions. The optimal process condition for alkaline peroxide pretreatment was identified for the fiber to pretreatment solution (S/S) ratio of 1/40 at 50°C for 5h with respect to all response variables (lignin removal, hemicellulose recovery, recovery of solid pretreated material, and crystallinity of lignocellulose). Three-way ANOVA results revealed that S/S ratio had no significant effect; whereas, both temperature and time, and the combination of parameters, exhibited significant effect on response variables. The characteristic peaks associated with lignin and cellulose demonstrated a higher amount of lignin removal and increased cellulose content with elevated treatment time. Autoclave assisted pretreatment proved to be inefficient due to removal of lower amount of lignin in addition to higher hemicellulose degradation. On the other hand, pretreatment using ultrasound was found to be most effective in removing lignin, liberating hemicelluloses along with diminition in cellulose crystallinity.
- 2 February 2018
- Published by Taylor & Francis in Journal of Natural Fibers
- Vol. 16 (5) , 662-676
Valorization of Lignocellulosic Waste (Crotalariajuncea) Using Alkaline Peroxide Pretreatment under Different Process Conditions: An Optimization Study on Separation of Lignin, Cellulose, and Hemicellulose
Lignocellulose materials, essentially consisting of lignin, cellulose and hemicelluloses, are abundant sources of fermentable sugars. The bast fiber of Crotalaria juncea (Sunn hemp), a native cover crop of India, was used as feedstock for this study. The primary objective of this study was to add value to the waste C. juncea bast fiber. The same was achieved by pretreating the waste fiber using alkaline peroxide solution at various process conditions. The optimal process condition for alkaline peroxide pretreatment was identified for the fiber to pretreatment solution (S/S) ratio of 1/40 at 50°C for 5h with respect to all response variables (lignin removal, hemicellulose recovery, recovery of solid pretreated material, and crystallinity of lignocellulose). Three-way ANOVA results revealed that S/S ratio had no significant effect; whereas, both temperature and time, and the combination of parameters, exhibited significant effect on response variables. The characteristic peaks associated with lignin and cellulose demonstrated a higher amount of lignin removal and increased cellulose content with elevated treatment time. Autoclave assisted pretreatment proved to be inefficient due to removal of lower amount of lignin in addition to higher hemicellulose degradation. On the other hand, pretreatment using ultrasound was found to be most effective in removing lignin, liberating hemicelluloses along with diminition in cellulose crystallinity.
- 1 January 2017
- Published by Elsevier
- Vol. 40, 2893-2898
Attainable Region for Biobutanol Production