Michael Klippel
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Michael Klippel has a total of 58 co-authors. Here are the top co-authors by number of shared publications:
- Andrea Frangi
ETH Zurich
12 shared publications Alar Just
6 shared publications- Joachim Schmid
ETH Zürich Institut für Baustatik und Konstruktion Stefano‐Franscini‐Platz 5 8093 Zürich Schweiz
6 shared publications Joachim Schmid
5 shared publications- Mario Fontana
Institute of Structural Engineering ETH, Zurich, Switzerland
3 shared publications - Mattia Tiso
Tallinn University of Technology Ehitajate tee 5 19086 Tallinn Estonia
3 shared publications
Latest Publications
- 18 September 2023
- Published by Wiley in Bautechnik
- Vol. 100 (10) , 599-607
Hintergründe und Nachweisgrundlagen zur Brandschutzbemessung von Brettsperrholzkonstruktionen – Teil 2
- 18 September 2023
- Published by Wiley in Bautechnik
- Vol. 100 (10) , 599-607
Hintergründe und Nachweisgrundlagen zur Brandschutzbemessung von Brettsperrholzkonstruktionen – Teil 2
- 15 July 2022
- Published by Wiley in Bautechnik
- Vol. 99 (8) , 587-593
Hintergründe und Nachweisgrundlagen zur Brandschutzbemessung von Brettsperrholzkonstruktionen – Teil 1
- 15 July 2022
- Published by Wiley in Bautechnik
- Vol. 99 (8) , 587-593
Hintergründe und Nachweisgrundlagen zur Brandschutzbemessung von Brettsperrholzkonstruktionen – Teil 1
- Open Access
- 25 January 2021
- Published by MDPI AG in Sustainability
- Vol. 13 (3) , 1237
Investigations on the Sustainable Resource Use of Swiss Timber
In Switzerland, the advantages of timber buildings for the climate are broadly discussed. In the following paper, a comparative sustainability assessment of four building alternatives is presented. Especially the contribution of implementing Swiss timber versus the implementation of imported timber is highlighted. Additionally, the timber-hybrid building structures are compared to a pure reinforced concrete structure. The timber-hybrid structure, with Swiss timber, has clear ecological advantages with only half the greenhouse gas emissions and half the non-renewable energy consumption compared to the reinforced concrete alternative. Comparing the Swiss timber alternative to the imported timber alternative, there are clear ecological advantages, as well. In terms of economic and social sustainability assessment criteria, the reinforced concrete alternative has the lowest production costs and the lowest labor intensity (measured in terms of full-time equivalents). Additionally, the paper includes an analysis of biogenic CO2 emissions and CO2 storage within the timber building alternatives. Finally, an up-scaling to the national level is attempted, showcasing the ecological and economic advantages of promoting the use of locally produced timber.
- 25 January 2021
- Published by MDPI AG in Sustainability
- Vol. 13 (3) , 1237
Open AccessInvestigations on the Sustainable Resource Use of Swiss Timber
In Switzerland, the advantages of timber buildings for the climate are broadly discussed. In the following paper, a comparative sustainability assessment of four building alternatives is presented. Especially the contribution of implementing Swiss timber versus the implementation of imported timber is highlighted. Additionally, the timber-hybrid building structures are compared to a pure reinforced concrete structure. The timber-hybrid structure, with Swiss timber, has clear ecological advantages with only half the greenhouse gas emissions and half the non-renewable energy consumption compared to the reinforced concrete alternative. Comparing the Swiss timber alternative to the imported timber alternative, there are clear ecological advantages, as well. In terms of economic and social sustainability assessment criteria, the reinforced concrete alternative has the lowest production costs and the lowest labor intensity (measured in terms of full-time equivalents). Additionally, the paper includes an analysis of biogenic CO2 emissions and CO2 storage within the timber building alternatives. Finally, an up-scaling to the national level is attempted, showcasing the ecological and economic advantages of promoting the use of locally produced timber.
- 1 February 2020
- Published by Elsevier in Engineering Structures
- Vol. 205
Bayesian calibration and sensitivity analysis of heat transfer models for fire insulation panels
- 1 February 2020
- Published by Elsevier in Engineering Structures
- Vol. 205
Bayesian calibration and sensitivity analysis of heat transfer models for fire insulation panels
- Open Access
- 1 January 2020
- Published by Tech Science Press in Journal of Renewable Materials
- Vol. 8 (9) , 1091-1109
Mechanical Characterisation of Densified Hardwood with Regard to Structural Applications
The demand for high-performance, yet eco-friendly materials is increasing on all scales from small applications in the car industry, instrument or furniture manufacturing to greater dimensions like floorings, balcony furnishings and even construction. Wood offers a good choice on all of these scales and can be modified and improved in many different ways. In this study, two common European hardwood species, Beech (Fagus sylvatica L.) and Ash (Fraxinus excelsior L.) were densified in radial direction by thermo-mechanical treatment and the densified product was investigated in an extensive characterisation series to determine all relevant mechanical properties. Compression in the three main directions (longitudinal, tangential, radial) and tension perpendicular to the grain (tangential, radial) were tested and compared to reference specimens with native density. Strength and modulus of elasticity were determined in all tests. In addition, a Life Cycle Assessment was carried out to evaluate the environmental impact associated to the densification process. The experimental investigations showed that strength and stiffness of hardwood in the longitudinal and tangential directions improve significantly by radial densification, whereas some properties in the radial direction decrease. The Life Cycle Assessment showed that artificial wood drying has higher impact than wood densification. Furthermore, the transport distance of the raw material highly influences the environmental impact of the final densified product. The paper then also offers an overview of possible applications in structural timber construction. Densified hardwood is a viable option as local reinforcement, where high compressive or tensile strength is needed. The wood densification process offers an alternative to the use of carbon-intense steel components or hardwoods from tropical forests.
- 1 January 2020
- Published by Tech Science Press in Journal of Renewable Materials
- Vol. 8 (9) , 1091-1109
Open AccessMechanical Characterisation of Densified Hardwood with Regard to Structural Applications
The demand for high-performance, yet eco-friendly materials is increasing on all scales from small applications in the car industry, instrument or furniture manufacturing to greater dimensions like floorings, balcony furnishings and even construction. Wood offers a good choice on all of these scales and can be modified and improved in many different ways. In this study, two common European hardwood species, Beech (Fagus sylvatica L.) and Ash (Fraxinus excelsior L.) were densified in radial direction by thermo-mechanical treatment and the densified product was investigated in an extensive characterisation series to determine all relevant mechanical properties. Compression in the three main directions (longitudinal, tangential, radial) and tension perpendicular to the grain (tangential, radial) were tested and compared to reference specimens with native density. Strength and modulus of elasticity were determined in all tests. In addition, a Life Cycle Assessment was carried out to evaluate the environmental impact associated to the densification process. The experimental investigations showed that strength and stiffness of hardwood in the longitudinal and tangential directions improve significantly by radial densification, whereas some properties in the radial direction decrease. The Life Cycle Assessment showed that artificial wood drying has higher impact than wood densification. Furthermore, the transport distance of the raw material highly influences the environmental impact of the final densified product. The paper then also offers an overview of possible applications in structural timber construction. Densified hardwood is a viable option as local reinforcement, where high compressive or tensile strength is needed. The wood densification process offers an alternative to the use of carbon-intense steel components or hardwoods from tropical forests.
- 1 November 2019
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 145 (11)
Literature Review on Timber–Concrete Composite Structures in Fire
- 1 November 2019
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 145 (11)
Literature Review on Timber–Concrete Composite Structures in Fire
- Open Access
- 1 November 2019
- Published by Elsevier in Energy and Buildings
- Vol. 202
Diffusion of energy efficiency technologies in European residential buildings: A bibliometric analysis
- 1 November 2019
- Published by Elsevier in Energy and Buildings
- Vol. 202
Open AccessDiffusion of energy efficiency technologies in European residential buildings: A bibliometric analysis
- 11 July 2019
- Published by Wiley in Bautechnik
- Vol. 96 (11) , 824-831
Vorschlag einer Standardprüfmethode für Brettsperrholz im Brandfall
Brettsperrholz (BSP oder engl. Cross‐Laminated Timber, CLT) ist in den letzten Jahren zu einem beliebten Holzprodukt für hochwertige und innovative Holzbauten geworden. Wie bei jedem Bauprodukt müssen das Brandverhalten und der Feuerwiderstand von CLT‐Elementen bei der Planung von Gebäuden sorgfältig geprüft werden. Der Klebstoff, der in den Klebfugen von CLT verwendet wird, spielt eine wichtige Rolle bei der Brandbemessung. Derzeit stellen die europäischen Normen jedoch keine Prüfmethode zur Verfügung, um die Klebfugeneigenschaften im Brandfall von CLT zu beurteilen. An der ETH Zürich wurden im letzten Jahr Brandprüfungen mit CLT‐Deckenelementen durchgeführt, in denen Klebstoffe mit verschiedenen Eigenschaften im Brandfall geprüft wurden. Der vorliegende Aufsatz stellt die Ergebnisse dieser Brandprüfungen dar und zeigt die Grundlagen einer möglichen europäischen Prüfmethode zur Klassifizierung von Flächenverklebungen. Dabei wird gezeigt, dass der Massenverlust von verklebten CLT‐Elementen während eines EN/ISO‐Normbrands verwendet werden kann, um die Funktionsfähigkeit der Klebstofffuge im Brandfall (Haftvermögen) zu bewerten.
- 11 July 2019
- Published by Wiley in Bautechnik
- Vol. 96 (11) , 824-831
Vorschlag einer Standardprüfmethode für Brettsperrholz im Brandfall
Brettsperrholz (BSP oder engl. Cross‐Laminated Timber, CLT) ist in den letzten Jahren zu einem beliebten Holzprodukt für hochwertige und innovative Holzbauten geworden. Wie bei jedem Bauprodukt müssen das Brandverhalten und der Feuerwiderstand von CLT‐Elementen bei der Planung von Gebäuden sorgfältig geprüft werden. Der Klebstoff, der in den Klebfugen von CLT verwendet wird, spielt eine wichtige Rolle bei der Brandbemessung. Derzeit stellen die europäischen Normen jedoch keine Prüfmethode zur Verfügung, um die Klebfugeneigenschaften im Brandfall von CLT zu beurteilen. An der ETH Zürich wurden im letzten Jahr Brandprüfungen mit CLT‐Deckenelementen durchgeführt, in denen Klebstoffe mit verschiedenen Eigenschaften im Brandfall geprüft wurden. Der vorliegende Aufsatz stellt die Ergebnisse dieser Brandprüfungen dar und zeigt die Grundlagen einer möglichen europäischen Prüfmethode zur Klassifizierung von Flächenverklebungen. Dabei wird gezeigt, dass der Massenverlust von verklebten CLT‐Elementen während eines EN/ISO‐Normbrands verwendet werden kann, um die Funktionsfähigkeit der Klebstofffuge im Brandfall (Haftvermögen) zu bewerten.
- 1 July 2019
- Published by Elsevier in Fire Safety Journal
- Vol. 107, 149-160
Procedure for implementing new materials to the component additive method
- 1 July 2019
- Published by Elsevier in Fire Safety Journal
- Vol. 107, 149-160
Procedure for implementing new materials to the component additive method
- 1 July 2019
- Published by Elsevier in Fire Safety Journal
- Vol. 107, 137-148
Evaluation of zero-strength layer depths for timber members of floor assemblies with heat resistant cavity insulations
- 1 July 2019
- Published by Elsevier in Fire Safety Journal
- Vol. 107, 137-148
Evaluation of zero-strength layer depths for timber members of floor assemblies with heat resistant cavity insulations