Mohammad Mehdi Moniri
Research Subjects
Research Interests
Mohammad Mehdi Moniri has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Seyed Mohammad Zeyb Sayyadan
Dept. of Mechatronics Engineering, Islamic Azad University, Science and Research Branch, Tehran (Semnan), Iran
4 shared publications Alexander Prange
German Research Center for Artificial Intelligence (DFKI), Saarbruecken, Germany
1 shared publicationAndreas Luxenburger
German Research Center for Artificial Intelligence (DFKI), Saarbruecken, Germany
1 shared publication- Christian Alfons Müller
German Research Center for Artificial Intelligence (DFKI), Saarbrcken, Germany
1 shared publication - Daniel Sonntag
German Research Center for Artificial Intelligence (DFKI), Saarbrücken, Germany
1 shared publication Faezeh Gharib
Dept. of Mechatronics Engineering, Islamic Azad University, Science and Research Branch, Tehran (Semnan), Iran
1 shared publication
Latest Publications
- 20 May 2021
- Published by IOP Publishing in Engineering Research Express
- Vol. 3 (2) , 025029
A bio-inspired soft planar actuator capable of broadening its working area
Soft actuators are an integral part of many soft robots that make them compliant and adaptable. In many previous studies, soft pneumatic actuators were designed and utilized generally to create bending motions. Due to the limited capabilities becomes ineffective where axial elongation is required. Here, we introduce a planar bioinspired soft pneumatic actuator capable of increasing its working area through both longitudinal elongation and bending motions, separately and or simultaneously. The actuator consists of two similar linear soft pneumatic actuators with agap between them. To study the performance of the planar actuator, four normalized sizes of gaps were considered between the linear actuators, analyzed through FEM, and validated by conducting experimental tests. On average, experimental results on the planar actuator demonstrate that the working area is 2.40 times bigger than the working area that just resulted from the bending motion. The results also indicate that the actuator can attain stability under 0.8 s, create a blocked force up to 18 N, and a bending angle up to 240° at the pressure 3.0Bars. Broadening the working area can be an outstanding feature that enables soft robots to be versatile and advantageous in many more applications in real and unstructured environments.
- 20 May 2021
- Published by IOP Publishing in Engineering Research Express
- Vol. 3 (2) , 025029
A bio-inspired soft planar actuator capable of broadening its working area
Soft actuators are an integral part of many soft robots that make them compliant and adaptable. In many previous studies, soft pneumatic actuators were designed and utilized generally to create bending motions. Due to the limited capabilities becomes ineffective where axial elongation is required. Here, we introduce a planar bioinspired soft pneumatic actuator capable of increasing its working area through both longitudinal elongation and bending motions, separately and or simultaneously. The actuator consists of two similar linear soft pneumatic actuators with agap between them. To study the performance of the planar actuator, four normalized sizes of gaps were considered between the linear actuators, analyzed through FEM, and validated by conducting experimental tests. On average, experimental results on the planar actuator demonstrate that the working area is 2.40 times bigger than the working area that just resulted from the bending motion. The results also indicate that the actuator can attain stability under 0.8 s, create a blocked force up to 18 N, and a bending angle up to 240° at the pressure 3.0Bars. Broadening the working area can be an outstanding feature that enables soft robots to be versatile and advantageous in many more applications in real and unstructured environments.
- 10 September 2018
- Published by Springer Nature in International Journal of Intelligent Robotics and Applications
- Vol. 3 (1) , 71-86
Mechanical behaviors of jammable robotic structures; prediction and computation
- 10 September 2018
- Published by Springer Nature in International Journal of Intelligent Robotics and Applications
- Vol. 3 (1) , 71-86
Mechanical behaviors of jammable robotic structures; prediction and computation
- 1 August 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 664-669
Stiffness variations in granular jamming robots; an experimental method
One of the most challenging issues of granular jamming robots is both predicting and measuring the stiffness variations which are a direct function of elastic module. In this regard, in previous researches, it had demonstrated that the elastic module of robot's bulk is a fundamental function of vacuum pressure and must be acquired by experimental tests. However, there was not a unique formulation for both computing and predicting the accurate elastic module in each unique amount of vacuum pressure. Therefore, in this paper, for addressing the problem, the elastic module of jammable segments is calculated in each considered vacuum pressure and we have introduced a both simple and beneficial formulation to predict the amounts of stiffness based on variations of vacuum pressure. The proposed procedure was examined by performing an experimental test as well. On the other hand, the necessity of identifying organic material was felt due to introduction of just one organic granular material in previous researches for applying. Hence, four new organic granular materials were selected and also tested. Consequently, a usable blend of two of them was presented which was mixed of black Pepper seeds and Datura grains. This blend had a lightweight construction with high ratio of strength under external forces, therefore, it can be applied when a both high-strength and lightweight jammable structure in robotics is required.
- 1 August 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 664-669
Stiffness variations in granular jamming robots; an experimental method
One of the most challenging issues of granular jamming robots is both predicting and measuring the stiffness variations which are a direct function of elastic module. In this regard, in previous researches, it had demonstrated that the elastic module of robot's bulk is a fundamental function of vacuum pressure and must be acquired by experimental tests. However, there was not a unique formulation for both computing and predicting the accurate elastic module in each unique amount of vacuum pressure. Therefore, in this paper, for addressing the problem, the elastic module of jammable segments is calculated in each considered vacuum pressure and we have introduced a both simple and beneficial formulation to predict the amounts of stiffness based on variations of vacuum pressure. The proposed procedure was examined by performing an experimental test as well. On the other hand, the necessity of identifying organic material was felt due to introduction of just one organic granular material in previous researches for applying. Hence, four new organic granular materials were selected and also tested. Consequently, a usable blend of two of them was presented which was mixed of black Pepper seeds and Datura grains. This blend had a lightweight construction with high ratio of strength under external forces, therefore, it can be applied when a both high-strength and lightweight jammable structure in robotics is required.
- Open Access
- 12 September 2016
- Published by Association for Computing Machinery (ACM)
- p. 321-324
MedicaLVR
We present a virtual reality framework and assistive tool for design practices for new medical environments, grounded on human visual perception, attention and action. This includes an interactive visualization of shared electronic patient records, previously acquired with a remote tablet device, in a virtual environment incorporating hand tracking, eye tracking and a vision-based peripheral view monitoring. The goal is to influence medical environments' affordances, especially for e-health and m-health applications as well as user experience and design conception for tele-medicine.
- 12 September 2016
- Published by Association for Computing Machinery (ACM)
- p. 321-324
Open AccessMedicaLVR
We present a virtual reality framework and assistive tool for design practices for new medical environments, grounded on human visual perception, attention and action. This includes an interactive visualization of shared electronic patient records, previously acquired with a remote tablet device, in a virtual environment incorporating hand tracking, eye tracking and a vision-based peripheral view monitoring. The goal is to influence medical environments' affordances, especially for e-health and m-health applications as well as user experience and design conception for tele-medicine.
- 1 October 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 557-562
A novel design of wall climbing robot for inspection of storage steel tanks
Manual inspection and maintenance of above ground storage tanks can be dangerous and time consuming. This paper presents a wall climbing mobile robot with permanent magnetic adhesion mechanism which can be used for tank inspection. The architecture of mechanical system is attended to in detail. Through a static and dynamic analysis, permanent magnetic adhesion mechanism is chosen for the robot. The tracked locomotion mechanism and the magnetic wheels are used simultaneously. After the robot modeling, the parameters design for the adhesion and locomotion mechanisms are derived.
- 1 October 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 557-562
A novel design of wall climbing robot for inspection of storage steel tanks
Manual inspection and maintenance of above ground storage tanks can be dangerous and time consuming. This paper presents a wall climbing mobile robot with permanent magnetic adhesion mechanism which can be used for tank inspection. The architecture of mechanical system is attended to in detail. Through a static and dynamic analysis, permanent magnetic adhesion mechanism is chosen for the robot. The tracked locomotion mechanism and the magnetic wheels are used simultaneously. After the robot modeling, the parameters design for the adhesion and locomotion mechanisms are derived.
- 1 June 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 379-382
Personalized In-Vehicle Information Systems: Building an Application Infrastructure for Smart Cars in Smart Spaces
Although intelligent components in modern cars help to contribute to safe mobility, they lack important Smart Environment characteristics like personalization. Moreover, today's in-vehicle infotainment systems do not offer any interaction possibility between the passenger and the visible environment around the car. In this paper we combine several technologies and propose an approach on personalized user interaction in urban environments. We present a showcase that points out the interplay of personalized in-vehicle infotainment system and interaction with visible outside environment.
- 1 June 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 379-382
Personalized In-Vehicle Information Systems: Building an Application Infrastructure for Smart Cars in Smart Spaces
Although intelligent components in modern cars help to contribute to safe mobility, they lack important Smart Environment characteristics like personalization. Moreover, today's in-vehicle infotainment systems do not offer any interaction possibility between the passenger and the visible environment around the car. In this paper we combine several technologies and propose an approach on personalized user interaction in urban environments. We present a showcase that points out the interplay of personalized in-vehicle infotainment system and interaction with visible outside environment.