Abdulrahman Jamal Babqi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Abdulrahman Jamal Babqi has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Zhehan Yi
GEIRI North America
3 shared publications Amir H. Etemadi
Department of Electrical and Computer Engineering, The George Washington University, Washington, DC, USA 20052
2 shared publications- Ahmed Althobaiti
Taif University
1 shared publication - Ambe Harrison
Department of Electrical and Electronics Engineering, College of Technology (COT), University of Buea, Buea, Cameroon
1 shared publication - Amir Hossein Etemadi
Department of Electrical and Computer Engineering, The George Washington University, Washington, DC, USA
1 shared publication - Asier Ibeas
Department of Telecommunications and Systems Engineering, Universitat Autònoma de Barcelona, Bellaterra, 08193 Barcelona, Spain
1 shared publication
Latest Publications
- Open Access
- 15 March 2024
- Published by Institution of Engineering and Technology (IET) in IET Generation, Transmission & Distribution
- Vol. 18 (8) , 1576-1589
Driving an asynchronous motor powered by PV‐MPPT using equivalent RST controller of fractional order PI and IP, based on generalized predictive control
The article introduces a new model of a Reference Signal Tracking (RST) controller for the fractional order quantities. The controller is applied to an indirect field‐oriented control (IFOC) system used for the speed control of an asynchronous motor powered by a photovoltaic (PV) generator with a maximum power point tracking (MPPT) algorithm. This model utilizes two fractional order controllers: the fractional order proportional‐integral (FOPI) regulator and the fractional‐order integral‐proportional (FOIP) regulator. These controllers are used with the generalized predictive control (GPC) technique. The first step in the approach is to derive the equivalent digital RST controller's model from the FOPI and FOIP controller's transfer functions. The GPC technique converts the continuous‐time FOPI (and FOIP) controller into a discrete‐time version. This conversion ensures a fast response and effective disturbance rejection. Simulation tests are conducted to analyze the rotor speed and stator current ripples to evaluate the performance of the proposed method. The results demonstrate the effectiveness of the introduced scheme in achieving improved control performance in terms of response speed and disturbance rejection. The article presents a modified RST controller model based on the fractional order approach applied to an IFOC system for motor speed control driven by a photovoltaic generator. Using FOPI, FOIP controllers, and GPC contributes to enhanced control performance, as evidenced by the simulation results.
- 15 March 2024
- Published by Institution of Engineering and Technology (IET) in IET Generation, Transmission & Distribution
- Vol. 18 (8) , 1576-1589
Open AccessDriving an asynchronous motor powered by PV‐MPPT using equivalent RST controller of fractional order PI and IP, based on generalized predictive control
The article introduces a new model of a Reference Signal Tracking (RST) controller for the fractional order quantities. The controller is applied to an indirect field‐oriented control (IFOC) system used for the speed control of an asynchronous motor powered by a photovoltaic (PV) generator with a maximum power point tracking (MPPT) algorithm. This model utilizes two fractional order controllers: the fractional order proportional‐integral (FOPI) regulator and the fractional‐order integral‐proportional (FOIP) regulator. These controllers are used with the generalized predictive control (GPC) technique. The first step in the approach is to derive the equivalent digital RST controller's model from the FOPI and FOIP controller's transfer functions. The GPC technique converts the continuous‐time FOPI (and FOIP) controller into a discrete‐time version. This conversion ensures a fast response and effective disturbance rejection. Simulation tests are conducted to analyze the rotor speed and stator current ripples to evaluate the performance of the proposed method. The results demonstrate the effectiveness of the introduced scheme in achieving improved control performance in terms of response speed and disturbance rejection. The article presents a modified RST controller model based on the fractional order approach applied to an IFOC system for motor speed control driven by a photovoltaic generator. Using FOPI, FOIP controllers, and GPC contributes to enhanced control performance, as evidenced by the simulation results.
- 2 August 2022
- Published by Taylor & Francis in International Journal of Green Energy
- Vol. 20 (7) , 767-783
Expert knowledge based proportional resonant controller for three phase inverter under abnormal grid conditions
Integration of photovoltaic (PV) power to the grid is achieved using three-phase inverters with high-quality current waveforms. The new grid codes impose a limit on the total harmonic distortion (THD) value of the inverter’s current waveforms. Due to simple structure and ease of design, proportional integral (PI) controllers are the most widely adopted methods to control three-phase grid-connected inverters; however under abnormal grid conditions, PI controllers may suffer from instability problems. To address the aforementioned problem, this article proposes an expert knowledge-based proportional resonant (PR) control for the integration of PV power to the grid under abnormal grid conditions. The proposed control method adjusts the control parameters based on rules generated from expert knowledge. Initially, parameters of the proposed control methods are optimized using particle swarm optimization (PSO) method. The proposed control is tested with a 100 kW grid-tied three-phase inverter unit under normal and abnormal grid conditions and its performance are compared with PI and fixed gain PR control methods. Moreover, the proposed control is tested experimentally with a scaled down 300 W grid-tied inverter lab prototype module. From the simulation and experimental results, it is verified that the proposed adaptive PR control technique is capable of providing low THD in the injected current under abnormal grid conditions compared with fixed gained PR controllers.
- 2 August 2022
- Published by Taylor & Francis in International Journal of Green Energy
- Vol. 20 (7) , 767-783
Expert knowledge based proportional resonant controller for three phase inverter under abnormal grid conditions
Integration of photovoltaic (PV) power to the grid is achieved using three-phase inverters with high-quality current waveforms. The new grid codes impose a limit on the total harmonic distortion (THD) value of the inverter’s current waveforms. Due to simple structure and ease of design, proportional integral (PI) controllers are the most widely adopted methods to control three-phase grid-connected inverters; however under abnormal grid conditions, PI controllers may suffer from instability problems. To address the aforementioned problem, this article proposes an expert knowledge-based proportional resonant (PR) control for the integration of PV power to the grid under abnormal grid conditions. The proposed control method adjusts the control parameters based on rules generated from expert knowledge. Initially, parameters of the proposed control methods are optimized using particle swarm optimization (PSO) method. The proposed control is tested with a 100 kW grid-tied three-phase inverter unit under normal and abnormal grid conditions and its performance are compared with PI and fixed gain PR control methods. Moreover, the proposed control is tested experimentally with a scaled down 300 W grid-tied inverter lab prototype module. From the simulation and experimental results, it is verified that the proposed adaptive PR control technique is capable of providing low THD in the injected current under abnormal grid conditions compared with fixed gained PR controllers.
- 17 May 2022
- Published by Periodica Polytechnica Budapest University of Technology and Economics in Periodica Polytechnica Electrical Engineering and Computer Science
- Vol. 66 (2) , 163-173
A Novel Model Predictive Control for Stability Improvement of Small Scaled Zero-inertia Multiple DGs Micro-grid
A zero-inertia micro-grid is a power system consisting of multiple renewable energy power sources and energy storage systems without the presence of conventional synchronous generators. In such a system, a large variation of the load or source sides during the islanded mode of operation extremely degrades the micro-grid's voltage and frequency stability. This study presents a virtual inertia-based predictive control strategy for a small-scale zero-inertia multiple distributed generators (DGs) micro-grid. In islanded mode, Voltage Model Predictive Control (VMPC) was implemented to control and maintain the voltage and frequency of the micro-grid. However, instabilities in frequency and voltage may rise at the Point of Common Coupling (PCC) due to large variations at both source and load sides. Therefore, the proposed virtual inertia loop calculates the amount of active power to be delivered or absorbed by each DG, and its effect is reflected in the estimated d current component of the VMPC, thus providing better frequency regulation. In grid-connected mode, Direct Power Model Predictive Control (DPMPC) was implemented to manage the power flow between each DG and the utility grid. The control approach also enables the DG plug and play characteristics. The performance of the control strategy was investigated and verified using the PSCAD/EMTDC software platform.
- 17 May 2022
- Published by Periodica Polytechnica Budapest University of Technology and Economics in Periodica Polytechnica Electrical Engineering and Computer Science
- Vol. 66 (2) , 163-173
A Novel Model Predictive Control for Stability Improvement of Small Scaled Zero-inertia Multiple DGs Micro-grid
A zero-inertia micro-grid is a power system consisting of multiple renewable energy power sources and energy storage systems without the presence of conventional synchronous generators. In such a system, a large variation of the load or source sides during the islanded mode of operation extremely degrades the micro-grid's voltage and frequency stability. This study presents a virtual inertia-based predictive control strategy for a small-scale zero-inertia multiple distributed generators (DGs) micro-grid. In islanded mode, Voltage Model Predictive Control (VMPC) was implemented to control and maintain the voltage and frequency of the micro-grid. However, instabilities in frequency and voltage may rise at the Point of Common Coupling (PCC) due to large variations at both source and load sides. Therefore, the proposed virtual inertia loop calculates the amount of active power to be delivered or absorbed by each DG, and its effect is reflected in the estimated d current component of the VMPC, thus providing better frequency regulation. In grid-connected mode, Direct Power Model Predictive Control (DPMPC) was implemented to manage the power flow between each DG and the utility grid. The control approach also enables the DG plug and play characteristics. The performance of the control strategy was investigated and verified using the PSCAD/EMTDC software platform.
- 1 October 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1860-1865
Model Predictive Control of H5 Inverter for Transformerless PV Systems with Maximum Power Point Tracking and Leakage Current Reduction
Transformerless grid-connected solar photovoltaic (PV) systems have given rise to more research and commercial interests due to their multiple merits, e.g., low leakage current and small size. In this paper, a model-predictive-control (MPC)-based strategy for controlling transformerless H5 inverter for single-phase PV distributed generation system is proposed. The method further reduces the PV leakage current in a cost-effective and safe manner and it shows a satisfactory fault-ride-through capability. Moreover, for the first of its kind, PV maximum power point tracking is implemented in the single-stage H5 inverter using MPC-based controllers. Various case studies are carried out, which provide the result comparisons between the proposed and conventional control methods and verify the promising performance of the proposed method.
- 1 October 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1860-1865
Model Predictive Control of H5 Inverter for Transformerless PV Systems with Maximum Power Point Tracking and Leakage Current Reduction
Transformerless grid-connected solar photovoltaic (PV) systems have given rise to more research and commercial interests due to their multiple merits, e.g., low leakage current and small size. In this paper, a model-predictive-control (MPC)-based strategy for controlling transformerless H5 inverter for single-phase PV distributed generation system is proposed. The method further reduces the PV leakage current in a cost-effective and safe manner and it shows a satisfactory fault-ride-through capability. Moreover, for the first of its kind, PV maximum power point tracking is implemented in the single-stage H5 inverter using MPC-based controllers. Various case studies are carried out, which provide the result comparisons between the proposed and conventional control methods and verify the promising performance of the proposed method.
- Open Access
- 1 August 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Finite-Control-Set Model Predictive Control (FCS-MPC) for Islanded Hybrid Microgrids
Microgrids consisting of multiple distributed energy resources (DERs) provide a promising solution to integrate renewable energies, e.g., solar photovoltaic (PV) systems. Hybrid AC/DC microgrids leverage the merits of both AC and DC power systems. In this paper, a control strategy for islanded multi-bus hybrid microgrids is proposed based on the Finite-Control-Set Model Predictive Control (FCS-MPC) technologies. The control loops are expedited by predicting the future states and determining the optimal control action before switching signals are sent. The proposed algorithm eliminates the needs of PI, PWM, and droop components, and offers 1) accurate PV maximum power point tracking (MPPT) and battery charging/discharging control, 2) DC and multiple AC bus voltage/frequency regulation, 3) a precise power sharing scheme among DERs without voltage or frequency deviation, and 4) a unified MPC design flow for hybrid microgrids. Multiple case studies are carried out, which verify the satisfactory performance of the proposed method.
- 1 August 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Open AccessFinite-Control-Set Model Predictive Control (FCS-MPC) for Islanded Hybrid Microgrids
Microgrids consisting of multiple distributed energy resources (DERs) provide a promising solution to integrate renewable energies, e.g., solar photovoltaic (PV) systems. Hybrid AC/DC microgrids leverage the merits of both AC and DC power systems. In this paper, a control strategy for islanded multi-bus hybrid microgrids is proposed based on the Finite-Control-Set Model Predictive Control (FCS-MPC) technologies. The control loops are expedited by predicting the future states and determining the optimal control action before switching signals are sent. The proposed algorithm eliminates the needs of PI, PWM, and droop components, and offers 1) accurate PV maximum power point tracking (MPPT) and battery charging/discharging control, 2) DC and multiple AC bus voltage/frequency regulation, 3) a precise power sharing scheme among DERs without voltage or frequency deviation, and 4) a unified MPC design flow for hybrid microgrids. Multiple case studies are carried out, which verify the satisfactory performance of the proposed method.
- 1 September 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Centralized finite control set model predictive control for multiple distributed generator small-scale microgrids
This paper proposes a control and power sharing strategy for small-scale microgrids in both grid-connected and islanded modes based on the centralized Finite Control Set Model Predictive Control (FCS-MPC). In grid-connected mode, the controller is capable of managing the output power of each Distributed Generator (DG) and enables flexible power regulation between the microgrid and the utility grid. In islanded mode, the controller regulates the microgrid voltage and frequency, and provides a precise power sharing scheme among DGs. In addition, the power sharing can be adjusted flexibly by changing the sharing ratio. The proposed control also enables plug-and-play operation. Moreover, a smooth transition between the two modes of operation is achieved without any disturbance in the system. Case studies are carried out to verify the proposed control strategy with the PSCAD/EMTDA software package.
- 1 September 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Centralized finite control set model predictive control for multiple distributed generator small-scale microgrids
This paper proposes a control and power sharing strategy for small-scale microgrids in both grid-connected and islanded modes based on the centralized Finite Control Set Model Predictive Control (FCS-MPC). In grid-connected mode, the controller is capable of managing the output power of each Distributed Generator (DG) and enables flexible power regulation between the microgrid and the utility grid. In islanded mode, the controller regulates the microgrid voltage and frequency, and provides a precise power sharing scheme among DGs. In addition, the power sharing can be adjusted flexibly by changing the sharing ratio. The proposed control also enables plug-and-play operation. Moreover, a smooth transition between the two modes of operation is achieved without any disturbance in the system. Case studies are carried out to verify the proposed control strategy with the PSCAD/EMTDA software package.
- Open Access
- 12 June 2017
- Published by Institution of Engineering and Technology (IET) in IET Generation, Transmission & Distribution
- Vol. 11 (9) , 2164-2172
MPC‐based microgrid control with supplementary fault current limitation and smooth transition mechanisms
This study presents a control strategy for a microgrid that consists of multiple distributed generators (DGs), for both grid‐connected and islanded modes of operation, where every DG is interfaced to the main grid via a voltage sourced inverter (VSI). finite control set model predictive control (FCS‐MPC) is used as the primary controller to regulate the output power of each DG (in the grid‐connected mode) or the voltage of the point of DG coupling (in the islanded mode of operation). In the grid‐connected mode, direct power model predictive control (DPMPC) is implemented to manage the power flow between each DG and the main grid. In the islanded mode, voltage model predictive control (VMPC), as the primary control, and droop control, as the secondary control, are employed to control the output voltage of each DG and system frequency. The controller is equipped with a supplementary current limiting technique to limit the output current of each DG in case of overcurrent scenarios. The control approach also enables a smooth transition between the two modes. The performance of the control strategy is investigated and verified using PSCAD/EMTDC software platform.
- 12 June 2017
- Published by Institution of Engineering and Technology (IET) in IET Generation, Transmission & Distribution
- Vol. 11 (9) , 2164-2172
Open AccessMPC‐based microgrid control with supplementary fault current limitation and smooth transition mechanisms
This study presents a control strategy for a microgrid that consists of multiple distributed generators (DGs), for both grid‐connected and islanded modes of operation, where every DG is interfaced to the main grid via a voltage sourced inverter (VSI). finite control set model predictive control (FCS‐MPC) is used as the primary controller to regulate the output power of each DG (in the grid‐connected mode) or the voltage of the point of DG coupling (in the islanded mode of operation). In the grid‐connected mode, direct power model predictive control (DPMPC) is implemented to manage the power flow between each DG and the main grid. In the islanded mode, voltage model predictive control (VMPC), as the primary control, and droop control, as the secondary control, are employed to control the output voltage of each DG and system frequency. The controller is equipped with a supplementary current limiting technique to limit the output current of each DG in case of overcurrent scenarios. The control approach also enables a smooth transition between the two modes. The performance of the control strategy is investigated and verified using PSCAD/EMTDC software platform.