Wissam Kadhim Alsaraj
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Wissam Kadhim Alsaraj has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Layth Abdulbari Al-Jaberi
Department of Civil Engineering, Mustansiriyah University, Baghdad 10047, Iraq
3 shared publications Hayam Yousuf Alhamdani
2 shared publicationsSahar Jabbar Alserai
2 shared publications- Akhlas H. Mohammed
Civil Engineering Department, College of Engineering, Mustansiriyah University
1 shared publication - Hanadi F. Naji1 shared publication
- Luma Abdul Ghani Zghair
Civil Engineering Department, Engineering College, Mustansiriyah University, Baghdad, Iraq
1 shared publication
Latest Publications
- Open Access
- 1 March 2026
- Published by Mustansiriyah University College of Engineering in Journal of Engineering and Sustainable Development
- Vol. 30 (2) , 269-276
Bearing Capacity of Sustainable Self-Compacting Concrete Walls
The experimental program includes testing thirteen wall panels divided into five categories; every group comprises three specimens. The first group explains the aspect ratio (AR) effect with three values (0.5,0.625 and 0.75). The increase in AR results in a decrease in the ultimate load and an increase in the lateral displacement. In the second group, the slenderness ratio (λ) is investigated by the ratios (11.43, 13.33, and 16). The maximum load increases and the displacement decreases as it decreases. The third and fourth groups clarify the opening’s effect (dimensions and locations). The results indicated a decrease in failure load and displacement as the size of the opening increases and as it approaches the edges. So, the largest load and displacement were when the opening was 15x25 cm at the center. The last group had the same details as the first group’s samples, but these were tested in a two-way manner that caused a rise in the loading capacity by 15%.
- 1 March 2026
- Published by Mustansiriyah University College of Engineering in Journal of Engineering and Sustainable Development
- Vol. 30 (2) , 269-276
Open AccessBearing Capacity of Sustainable Self-Compacting Concrete Walls
The experimental program includes testing thirteen wall panels divided into five categories; every group comprises three specimens. The first group explains the aspect ratio (AR) effect with three values (0.5,0.625 and 0.75). The increase in AR results in a decrease in the ultimate load and an increase in the lateral displacement. In the second group, the slenderness ratio (λ) is investigated by the ratios (11.43, 13.33, and 16). The maximum load increases and the displacement decreases as it decreases. The third and fourth groups clarify the opening’s effect (dimensions and locations). The results indicated a decrease in failure load and displacement as the size of the opening increases and as it approaches the edges. So, the largest load and displacement were when the opening was 15x25 cm at the center. The last group had the same details as the first group’s samples, but these were tested in a two-way manner that caused a rise in the loading capacity by 15%.
- Open Access
- 1 June 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 870 (1)
Influence of Nanoclay on the Behavior of Reinforced Concrete Slabs
The impact of using various percentage of nanoclay on the mechanical properties of concrete and on the flexural capacity of reinforced concrete two-way slabs was achieved in this study. The percentage of nanoclay content are (0%, 2%, 4%, 6%,8%, 10%) weight percent of cement, and in addition to the use of polypropylene content of 1.5%. The investigated mechanical properties of concrete were compressive strength, sp1itting tensi1e strength and f1exural strength. Six specimens of RC two way slabs were cast using those various content of nanocaly, the slabs were simply supported condition and under uniform load. Test indicated revealed significant improvement in the mechanical properties of concrete by using nanoclay due to its high pozzolanic activity which verifies the higher amount formation of C-S-H gel in the due to the presence of nanoparticles. When nanoclay proportion increased from 2% to 8%, the compressive strength increased about 3%, and 12.4%, respectively for samples with polypropylene equals 1.5%. While the splitting tensile strength increased by 4% up to 39.4% when using the same nanoclay proportion about 2% to 8%, respectively. The flexural modulus of rupture increased by 6%, and 36%, respectively for the same nanoclay proportion and polypropylene fiber content. The ultimate load capacity of the RC slabs increased by (12.5%) up to (66%) when the nanoclay content increased from (2% to 8%). However, using 10% nanoclay reduced the strength of the slab. In addition, different failure modes was observed for the slabs when using different percentage of nanoclay content.
- 1 June 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 870 (1)
Open AccessInfluence of Nanoclay on the Behavior of Reinforced Concrete Slabs
The impact of using various percentage of nanoclay on the mechanical properties of concrete and on the flexural capacity of reinforced concrete two-way slabs was achieved in this study. The percentage of nanoclay content are (0%, 2%, 4%, 6%,8%, 10%) weight percent of cement, and in addition to the use of polypropylene content of 1.5%. The investigated mechanical properties of concrete were compressive strength, sp1itting tensi1e strength and f1exural strength. Six specimens of RC two way slabs were cast using those various content of nanocaly, the slabs were simply supported condition and under uniform load. Test indicated revealed significant improvement in the mechanical properties of concrete by using nanoclay due to its high pozzolanic activity which verifies the higher amount formation of C-S-H gel in the due to the presence of nanoparticles. When nanoclay proportion increased from 2% to 8%, the compressive strength increased about 3%, and 12.4%, respectively for samples with polypropylene equals 1.5%. While the splitting tensile strength increased by 4% up to 39.4% when using the same nanoclay proportion about 2% to 8%, respectively. The flexural modulus of rupture increased by 6%, and 36%, respectively for the same nanoclay proportion and polypropylene fiber content. The ultimate load capacity of the RC slabs increased by (12.5%) up to (66%) when the nanoclay content increased from (2% to 8%). However, using 10% nanoclay reduced the strength of the slab. In addition, different failure modes was observed for the slabs when using different percentage of nanoclay content.
- 1 September 2019
- Published by Mustansiriyah University College of Engineering in Journal of Engineering and Sustainable Development
- Vol. 23 (05) , 1-11
SHEAR RESISTANCE OF MRPC LIGHTWEIGHT CONCRETE BEAMS WITHOUT STIRRUPS
- 1 September 2019
- Published by Mustansiriyah University College of Engineering in Journal of Engineering and Sustainable Development
- Vol. 23 (05) , 1-11
SHEAR RESISTANCE OF MRPC LIGHTWEIGHT CONCRETE BEAMS WITHOUT STIRRUPS
- 1 September 2019
- Published by Mustansiriyah University College of Engineering in Journal of Engineering and Sustainable Development
- Vol. 23 (05) , 12-25
SHEAR CAPACITY OF SELF COMPACTING CONCRETE DEEP BEAM UNDER CONSTRAINED AXIAL LOADS
- 1 September 2019
- Published by Mustansiriyah University College of Engineering in Journal of Engineering and Sustainable Development
- Vol. 23 (05) , 12-25
SHEAR CAPACITY OF SELF COMPACTING CONCRETE DEEP BEAM UNDER CONSTRAINED AXIAL LOADS
- 1 September 2019
- Published by Mustansiriyah University College of Engineering in Journal of Engineering and Sustainable Development
- Vol. 23 (4) , 119-131
SUGGESTED EQUATIONS FOR MECHANICAL PROPERTIES OF SELF COMPACTING CONCRETE STRENGTHENED WITH STEEL FIBERS AND EFFECT OF SUCH FIBERS ON SHEAR CAPACITY OF SIMPLY SUPPORTED DEEP BEAMS UNDER AXIAL LOADS
- 1 September 2019
- Published by Mustansiriyah University College of Engineering in Journal of Engineering and Sustainable Development
- Vol. 23 (4) , 119-131
SUGGESTED EQUATIONS FOR MECHANICAL PROPERTIES OF SELF COMPACTING CONCRETE STRENGTHENED WITH STEEL FIBERS AND EFFECT OF SUCH FIBERS ON SHEAR CAPACITY OF SIMPLY SUPPORTED DEEP BEAMS UNDER AXIAL LOADS
- 1 September 2019
- Published by Mustansiriyah University College of Engineering in Journal of Engineering and Sustainable Development
- Vol. 23 (04) , 145-154
MECHANICAL PROPERTIES OF MRP LIGHTWEIGHT CONCRETE AND EFFECT OF COMPRESSIVE STRENGTH ON SHEAR CAPACITY OF BEAMS
- 1 September 2019
- Published by Mustansiriyah University College of Engineering in Journal of Engineering and Sustainable Development
- Vol. 23 (04) , 145-154
MECHANICAL PROPERTIES OF MRP LIGHTWEIGHT CONCRETE AND EFFECT OF COMPRESSIVE STRENGTH ON SHEAR CAPACITY OF BEAMS
- Open Access
- 31 August 2019
- Published by Bentham Science Publishers Ltd. in The Open Civil Engineering Journal
- Vol. 13 (1) , 109-117
Structural Behavior of Geopolymer Concrete Thin Wall Panels Based on Metakaolin and Recycled Concrete Aggregate
Introduction: Due to the current popularity of Reinforced Concrete (RC) wall construction and the new published codes for concrete, RC walls have become just as important structural elements as beams, slabs and columns. Methods: This paper presents the structural behavior of geopolymer concrete thin wall panels based on metakaolin and recycled concrete aggregate subjected to axial eccentric uniformly distributed loading with varying Aspect Ratios (AR=H/L) and steel reinforcement ratios. The experimental program includes testing of five two-way thin geopolymer concrete wall panels; fixed at all sides and applying the load axially with eccentricity equal to the wall thickness/6. Results and Conclusion: The results indicate that the load-carrying capacity of the geopolymer concrete wall panels increased to about 63% with a decrease in AR (H/L) from 1.875 to 0.75. The lateral deflection decreased to about 50% with a decrease in AR (H/L) from 1.875 to 0.75. Also, the results show that the load-carrying capacity of the geopolymer concrete wall panels increased to nearly 48% with an increase in the steel reinforcement ratio from 2.32% to 3.38%. The lateral deflection also decreased by 20% with an increase in the steel reinforcement ratio to 3.38%. The results show that locally manufactured Metakaolin can be used for producing Geopolymer concrete.
- 31 August 2019
- Published by Bentham Science Publishers Ltd. in The Open Civil Engineering Journal
- Vol. 13 (1) , 109-117
Open AccessStructural Behavior of Geopolymer Concrete Thin Wall Panels Based on Metakaolin and Recycled Concrete Aggregate
Introduction: Due to the current popularity of Reinforced Concrete (RC) wall construction and the new published codes for concrete, RC walls have become just as important structural elements as beams, slabs and columns. Methods: This paper presents the structural behavior of geopolymer concrete thin wall panels based on metakaolin and recycled concrete aggregate subjected to axial eccentric uniformly distributed loading with varying Aspect Ratios (AR=H/L) and steel reinforcement ratios. The experimental program includes testing of five two-way thin geopolymer concrete wall panels; fixed at all sides and applying the load axially with eccentricity equal to the wall thickness/6. Results and Conclusion: The results indicate that the load-carrying capacity of the geopolymer concrete wall panels increased to about 63% with a decrease in AR (H/L) from 1.875 to 0.75. The lateral deflection decreased to about 50% with a decrease in AR (H/L) from 1.875 to 0.75. Also, the results show that the load-carrying capacity of the geopolymer concrete wall panels increased to nearly 48% with an increase in the steel reinforcement ratio from 2.32% to 3.38%. The lateral deflection also decreased by 20% with an increase in the steel reinforcement ratio to 3.38%. The results show that locally manufactured Metakaolin can be used for producing Geopolymer concrete.
- Open Access
- 31 December 2018
- Published by Bentham Science Publishers Ltd. in The Open Civil Engineering Journal
- Vol. 12 (1) , 441-457
Effect of Iron Filings on the Mechanical Properties of Different Types of Sustainable Concrete
Introduction: One of Iraq’s major environmental problems is a large amount of residual iron produced by the industrial sector, which is stored in domestic waste and landfills. The reuse of construction waste gives two aims, the first is to remove large quantities of pollution resulted from these waste, the second provides cheap resources for concrete aggregates.Methods: This study conducted a series of experiments and tests to test the feasibility of reusing this iron slag and recycled concrete aggregate in concrete mixtures. Different percentages of iron filings were used in the concrete mixture at 0, 0.5%, 0.75% and 1%. Tests are done to evaluate the quality of cast iron concrete which include compressive strength (fcu), flexural strength (fr), indirect tensile strength (ft), SEM and modulus of elasticity (Ec) for four sustainable concretes.Results and Conclusion: The results show that the iron filings amount is increased to 1.0% which resulted in increasing percentage of compressive strength (fcu), flexural strength (fr), indirect tensile strength (ft), SEM and modulus of elasticity (Ec) with 10%, 32%, 42% and 11% for Geopolymer Concrete with Recycled Aggregate (GCRA), 9%, 52%,31% and 17% for geopolymer concrete with natural aggregate (GCNA), 10%, 19%,26% and 12% for Normal Concrete with Natural Aggregate (NCNA) and 23%, 19%, 67% and 14% for Normal Concrete with Recycled Aggregate (NCRA), respectively.
- 31 December 2018
- Published by Bentham Science Publishers Ltd. in The Open Civil Engineering Journal
- Vol. 12 (1) , 441-457
Open AccessEffect of Iron Filings on the Mechanical Properties of Different Types of Sustainable Concrete
Introduction: One of Iraq’s major environmental problems is a large amount of residual iron produced by the industrial sector, which is stored in domestic waste and landfills. The reuse of construction waste gives two aims, the first is to remove large quantities of pollution resulted from these waste, the second provides cheap resources for concrete aggregates.Methods: This study conducted a series of experiments and tests to test the feasibility of reusing this iron slag and recycled concrete aggregate in concrete mixtures. Different percentages of iron filings were used in the concrete mixture at 0, 0.5%, 0.75% and 1%. Tests are done to evaluate the quality of cast iron concrete which include compressive strength (fcu), flexural strength (fr), indirect tensile strength (ft), SEM and modulus of elasticity (Ec) for four sustainable concretes.Results and Conclusion: The results show that the iron filings amount is increased to 1.0% which resulted in increasing percentage of compressive strength (fcu), flexural strength (fr), indirect tensile strength (ft), SEM and modulus of elasticity (Ec) with 10%, 32%, 42% and 11% for Geopolymer Concrete with Recycled Aggregate (GCRA), 9%, 52%,31% and 17% for geopolymer concrete with natural aggregate (GCNA), 10%, 19%,26% and 12% for Normal Concrete with Natural Aggregate (NCNA) and 23%, 19%, 67% and 14% for Normal Concrete with Recycled Aggregate (NCRA), respectively.
- Open Access
- 28 November 2018
- Published by Science Publishing Corporation in International Journal of Engineering & Technology
- Vol. 7 (4.20) , 399-402
Carbon Fiber Strengthening of Geopolymer Concrete Wall Panels with Iron Fillings
Wall is a vertical plate member resisting vertical (in-plane) or lateral loads. Load-Bearing walls were referred to RC wall panels which were commonly used as load-bearing structural members, braced and laterally supported by the rest of the structure, local materials such as Metakaolin and alkaline solutions are used to cast (600x400) mm reinforced concrete wall panels with 40 mm thickness. To find the ultimate bearing capacity and lateral deflection of wall panels. Seven specimens are divided in two groups to study the variation effect of iron filling (0, 0.5, 0.75 and 1.0)% and carbon fiber (225, 125 and 90 )mm spacing center to center of strips. The result shows that the maximum increasing are 17% and 14% for ultimate bearing capacity and cracking load of wall panels respectively, when iron filling is 1%. Also, the using of carbon fiber with 90 mm spacing center to center of strips leds to increasing in ultimate bearing capacity and cracking load by 31% and 7% respectively. Lateral deflection of wall panels was measured and compared with the reference wall to investigate the strengthening effect.
- 28 November 2018
- Published by Science Publishing Corporation in International Journal of Engineering & Technology
- Vol. 7 (4.20) , 399-402
Open AccessCarbon Fiber Strengthening of Geopolymer Concrete Wall Panels with Iron Fillings
Wall is a vertical plate member resisting vertical (in-plane) or lateral loads. Load-Bearing walls were referred to RC wall panels which were commonly used as load-bearing structural members, braced and laterally supported by the rest of the structure, local materials such as Metakaolin and alkaline solutions are used to cast (600x400) mm reinforced concrete wall panels with 40 mm thickness. To find the ultimate bearing capacity and lateral deflection of wall panels. Seven specimens are divided in two groups to study the variation effect of iron filling (0, 0.5, 0.75 and 1.0)% and carbon fiber (225, 125 and 90 )mm spacing center to center of strips. The result shows that the maximum increasing are 17% and 14% for ultimate bearing capacity and cracking load of wall panels respectively, when iron filling is 1%. Also, the using of carbon fiber with 90 mm spacing center to center of strips leds to increasing in ultimate bearing capacity and cracking load by 31% and 7% respectively. Lateral deflection of wall panels was measured and compared with the reference wall to investigate the strengthening effect.