Ozan Yoruk
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ozan Yoruk has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Murat Ates
Department of Chemistry, Faculty of Arts and Sciences, Tekirdag Namik Kemal University, Tekirdag, Turkey
9 shared publications - Yuksel Bayrak
Department of Chemistry, Faculty of Sciences, Trakya University, Edirne, Turkey
7 shared publications - Selda Alacamli Ozyurek
Department of Chemistry, Faculty of Arts and Sciences, Tekirdag Namik Kemal University
3 shared publications - Murat Yildirim
SAMSUN ÜNİVERSİTES
2 shared publications - Özge Kuzgun
Department of Intensive Care, Sakarya University Training and Research Hospital, Sakarya, Türkiye
2 shared publications Alpay Garip
Atespolymer Research Group, Physical Chemistry Division, Department of Chemistry, Faculty of Arts and Sciences, Namik Kemal University, Tekirdag, Turkey
1 shared publication
Latest Publications
- Open Access
- 10 January 2026
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 37 (2) , 171
Synergistic effects in rGO/Co3O4/PPy//rGO/CuO electrodes for high-performance asymmetric supercapacitors
Supercapacitors exhibit several fundamental advantages, including fast ion-transport, high charge–discharge capability, and high power density. In this study, an asymmetric supercapacitor configuration was designed in which a reduced graphene oxide (rGO), cobalt (II, III) oxide (Co 3 O 4 ), and polypyrrole (PPy) composite was employed as the positive ( +) electrode (cathode) deposited on aluminum foil, while an rGO/copper (II) oxide (CuO) composite served as the negative (-) electrode (anode) on copper foil. The cathode electrodes were prepared with initial feed ratios of [rGO] o /[Co 3 O 4 ] o /[Py] o = 1:5:1, 1:5:2, 1:5:5 and 1:5:10. Furthermore, the anode electrode was designed using rGO-supported doped CuO as the active material with a feed ratio of [rGO] o /[CuO] o = 1:1. The assembled electrodes were integrated into CR2032 coin cells to construct the asymmetric supercapacitor device. The characterization of the cathode electrode active materials has been reported in our previous study. Therefore, only the characterization of the anode electrode material is presented here, including BET, TGA-DTA SEM–EDX and FTIR-ATR analyses. An ionic liquid electrolyte was employed in the supercapacitor device to enhance the operating voltage window, as evidenced by the galvanostatic charge–discharge (GCD) measurements. The asymmetric rGO/Co 3 O 4 /PPy//rGO/CuO supercapacitor exhibited the highest specific capacitance for the electrode composition with an initial feed ratio of [rGO] o /[Co 3 O 4 ] o /[Py] o = 1:5:2. A specific capacitance of 1380 F/g was obtained at a scan rate of 2 mV/s using cyclic voltammetry (CV) method, while a value of 181.48 F/g was achieved at a current density of 10 A/g from GCD measurements. This superior electrochemical performance is further corroborated by the highest areal and volumetric capacitance values C A = 45.37 F/cm 2 and C V = 4537.04 F/cm 3 , respectively, measured at 10 A/g for the same composition. The capacitance retention of the asymmetric supercapacitor reached 89.1% for the electrode composition with an initial feed ratio of [rGO] o /[Co 3 O 4 ] o /[PPy] o = 1:5:10 after 1000 charge–discharge cycles, as evaluated by CV in a CR2032 coin cell. Moreover, the highest energy density was calculated to be E = 78.13 Wh/kg at a current density of 1 A/g. This performance is further supported by electrochemical impedance spectroscopy (EIS) results, which yielded a specific capacitance ( C s p ) of 0.283 F/g and a double-layer capacitance ( C dl ) of 0.129 F/g for the same composition. Overall, the newly designed asymmetric rGO/Co 3 O 4 /PPy//rGO/CuO electrode configuration demonstrates strong potential as an effective candidate for advanced supercapacitor applications.
- 10 January 2026
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 37 (2) , 171
Open AccessSynergistic effects in rGO/Co3O4/PPy//rGO/CuO electrodes for high-performance asymmetric supercapacitors
Supercapacitors exhibit several fundamental advantages, including fast ion-transport, high charge–discharge capability, and high power density. In this study, an asymmetric supercapacitor configuration was designed in which a reduced graphene oxide (rGO), cobalt (II, III) oxide (Co 3 O 4 ), and polypyrrole (PPy) composite was employed as the positive ( +) electrode (cathode) deposited on aluminum foil, while an rGO/copper (II) oxide (CuO) composite served as the negative (-) electrode (anode) on copper foil. The cathode electrodes were prepared with initial feed ratios of [rGO] o /[Co 3 O 4 ] o /[Py] o = 1:5:1, 1:5:2, 1:5:5 and 1:5:10. Furthermore, the anode electrode was designed using rGO-supported doped CuO as the active material with a feed ratio of [rGO] o /[CuO] o = 1:1. The assembled electrodes were integrated into CR2032 coin cells to construct the asymmetric supercapacitor device. The characterization of the cathode electrode active materials has been reported in our previous study. Therefore, only the characterization of the anode electrode material is presented here, including BET, TGA-DTA SEM–EDX and FTIR-ATR analyses. An ionic liquid electrolyte was employed in the supercapacitor device to enhance the operating voltage window, as evidenced by the galvanostatic charge–discharge (GCD) measurements. The asymmetric rGO/Co 3 O 4 /PPy//rGO/CuO supercapacitor exhibited the highest specific capacitance for the electrode composition with an initial feed ratio of [rGO] o /[Co 3 O 4 ] o /[Py] o = 1:5:2. A specific capacitance of 1380 F/g was obtained at a scan rate of 2 mV/s using cyclic voltammetry (CV) method, while a value of 181.48 F/g was achieved at a current density of 10 A/g from GCD measurements. This superior electrochemical performance is further corroborated by the highest areal and volumetric capacitance values C A = 45.37 F/cm 2 and C V = 4537.04 F/cm 3 , respectively, measured at 10 A/g for the same composition. The capacitance retention of the asymmetric supercapacitor reached 89.1% for the electrode composition with an initial feed ratio of [rGO] o /[Co 3 O 4 ] o /[PPy] o = 1:5:10 after 1000 charge–discharge cycles, as evaluated by CV in a CR2032 coin cell. Moreover, the highest energy density was calculated to be E = 78.13 Wh/kg at a current density of 1 A/g. This performance is further supported by electrochemical impedance spectroscopy (EIS) results, which yielded a specific capacitance ( C s p ) of 0.283 F/g and a double-layer capacitance ( C dl ) of 0.129 F/g for the same composition. Overall, the newly designed asymmetric rGO/Co 3 O 4 /PPy//rGO/CuO electrode configuration demonstrates strong potential as an effective candidate for advanced supercapacitor applications.
- Open Access
- 1 January 2026
- Published by Wiley in International Journal of Polymer Science
- Vol. 2026 (1)
Sustainable Cross‐Linked PVA/Hard Carbon Composite Films From Rice Husk With Enhanced Antioxidant and Antibacterial Performance
Sustainable utilization of agricultural waste in advanced polymeric materials offers an effective pathway toward environmentally responsible functional systems. In this study, cross‐linked poly(vinyl alcohol) (PVA) composite films reinforced with nitric acid–treated hard carbon (HNO 3 ‐HC) derived from rice husk were successfully fabricated and systematically investigated. Hard carbon was obtained via high‐temperature pyrolysis and subsequently functionalized using nitric acid to improve interfacial compatibility and bioactivity. Composite films containing 1.0, 1.5, and 2.5‐wt% HNO₃‐HC were prepared by solution casting followed by vapor‐phase glutaraldehyde cross‐linking. SEM and EDX analyses confirmed homogeneous dispersion of HNO 3 ‐HC within the PVA matrix, whereas FT‐IR results indicated enhanced hydrogen bonding interactions. Incorporation of HNO 3 ‐HC improved thermal stability, increasing the glass transition temperature from 74.9°C (neat PVA) to 84.3°C for the 2.5‐wt% composite. Water contact angle values decreased from 43.9° to 34.9°, indicating enhanced surface hydrophilicity. Mechanical testing revealed a transition from stiffness‐dominated to ductility‐dominated behavior with increasing filler content, with the highest work at break (1426 N·mm) observed for PVA‐HC‐2.5. Antioxidant activity increased with filler loading, reaching 13.7% (DPPH) and 27.1% (ABTS) inhibition at 60 min for the PVA‐HC‐2.5 sample. Antibacterial assays demonstrated bacterial reduction of up to 72% against Staphylococcus aureus and 65% against Pseudomonas aeruginosa , also observed for PVA‐HC‐2.5. In addition, the lowest water contact angle (34.9°) was recorded for the same formulation. These findings establish rice husk–derived HNO 3 ‐HC as a promising multifunctional biofiller for PVA, enabling the fabrication of sustainable composite films with consistent and measurable enhancements in antioxidant and antibacterial performance relative to pristine PVA.
- 1 January 2026
- Published by Wiley in International Journal of Polymer Science
- Vol. 2026 (1)
Open AccessSustainable Cross‐Linked PVA/Hard Carbon Composite Films From Rice Husk With Enhanced Antioxidant and Antibacterial Performance
Sustainable utilization of agricultural waste in advanced polymeric materials offers an effective pathway toward environmentally responsible functional systems. In this study, cross‐linked poly(vinyl alcohol) (PVA) composite films reinforced with nitric acid–treated hard carbon (HNO 3 ‐HC) derived from rice husk were successfully fabricated and systematically investigated. Hard carbon was obtained via high‐temperature pyrolysis and subsequently functionalized using nitric acid to improve interfacial compatibility and bioactivity. Composite films containing 1.0, 1.5, and 2.5‐wt% HNO₃‐HC were prepared by solution casting followed by vapor‐phase glutaraldehyde cross‐linking. SEM and EDX analyses confirmed homogeneous dispersion of HNO 3 ‐HC within the PVA matrix, whereas FT‐IR results indicated enhanced hydrogen bonding interactions. Incorporation of HNO 3 ‐HC improved thermal stability, increasing the glass transition temperature from 74.9°C (neat PVA) to 84.3°C for the 2.5‐wt% composite. Water contact angle values decreased from 43.9° to 34.9°, indicating enhanced surface hydrophilicity. Mechanical testing revealed a transition from stiffness‐dominated to ductility‐dominated behavior with increasing filler content, with the highest work at break (1426 N·mm) observed for PVA‐HC‐2.5. Antioxidant activity increased with filler loading, reaching 13.7% (DPPH) and 27.1% (ABTS) inhibition at 60 min for the PVA‐HC‐2.5 sample. Antibacterial assays demonstrated bacterial reduction of up to 72% against Staphylococcus aureus and 65% against Pseudomonas aeruginosa , also observed for PVA‐HC‐2.5. In addition, the lowest water contact angle (34.9°) was recorded for the same formulation. These findings establish rice husk–derived HNO 3 ‐HC as a promising multifunctional biofiller for PVA, enabling the fabrication of sustainable composite films with consistent and measurable enhancements in antioxidant and antibacterial performance relative to pristine PVA.
- 16 December 2025
- Published by Springer Nature in Ionics
- Vol. 32 (2) , 2091-2110
Correlation between structural properties and electrochemical performances of h-BN/AC/NiO/Poly(ANI-co-Py) electrodes for supercapacitors
- 16 December 2025
- Published by Springer Nature in Ionics
- Vol. 32 (2) , 2091-2110
Correlation between structural properties and electrochemical performances of h-BN/AC/NiO/Poly(ANI-co-Py) electrodes for supercapacitors
- 15 October 2025
- Published by Taylor & Francis in Journal of Macromolecular Science, Part A
- Vol. 62 (12) , 1197-1211
Prospective ultrathin layered Fe 2 O 3 doped reduced graphene oxide, polythiophene, and carbon black hybrid nanostructures for high performance supercapacitors
- 15 October 2025
- Published by Taylor & Francis in Journal of Macromolecular Science, Part A
- Vol. 62 (12) , 1197-1211
Prospective ultrathin layered Fe 2 O 3 doped reduced graphene oxide, polythiophene, and carbon black hybrid nanostructures for high performance supercapacitors
- 2 August 2025
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 142 (45)
Reduced Graphene Oxide, Molybdenum Disulfur, Polythiophene and Carbon Black Nanocomposite Formation and Their Supercapacitor Evaluations
In this paper, graphene oxide (GO), reduced graphene oxide (rGO), molybdenum disulfide (MoS 2 ), polythiophene (PTh), GO/MoS 2 /PTh, rGO/MoS 2 /PTh, and rGO/MoS 2 /PTh/carbon black (CB) nanocomposites were firstly synthesized to be used as a component of electrode material for supercapacitor devices. Thiophene monomer was chemically synthesized by an in‐situ oxidation polymerization method. The microwave‐irradiation method was used to form the reduction process of GO. The materials were characterized by scanning electron microscopy, energy dispersive x‐ray analysis, atomic force microscopy, thermogravimetric analysis (TGA) and, differential thermal analysis, Fourier transform infrared spectroscopy, and attenuated total reflectance analysis, Brunauer–Emmett–Teller analysis, four‐point probe conductivity, cyclic voltammetry, galvanostatic charge‐discharge and electrochemical impedance spectroscopy analysis. The TGA analysis shows that PTh has the most degradable material due to small polymer chains. However, the highest thermal stability (98.56%) was obtained for MoS 2 . The temperature raised up to 982°C. Moreover, the highest specific capacitance was calculated as C sp = 1588.72 F/g at 2 mV/s for the rGO/MoS 2 /PTh nanocomposite in a 6 M KOH electrolyte solution. In addition, the highest energy and power densities, specific capacitive retention, and the lowest equivalent series resistance (ESR) were presented for this nanocomposite as E = 3.20 Wh/kg at 10 mA, P = 1152.5 W/kg at 10 mA, 111.48% after 1000 charge–discharge cycles and ESR = 0.05 Ω at 10 mA, respectively. Equivalent ladder circuit model of R s ( C 1 ( R 1 ( R 2 C 2 ))) was also evaluated to interpret theoretical and experimental data using ZSimpWin 3.22 program. Results are compatible with each other. An easy preparation method and eco‐friendly synthesis were reported for rGO/MoS 2 /PTh/CB nanocomposite for next generation supercapacitor evaluations.
- 2 August 2025
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 142 (45)
Reduced Graphene Oxide, Molybdenum Disulfur, Polythiophene and Carbon Black Nanocomposite Formation and Their Supercapacitor Evaluations
In this paper, graphene oxide (GO), reduced graphene oxide (rGO), molybdenum disulfide (MoS 2 ), polythiophene (PTh), GO/MoS 2 /PTh, rGO/MoS 2 /PTh, and rGO/MoS 2 /PTh/carbon black (CB) nanocomposites were firstly synthesized to be used as a component of electrode material for supercapacitor devices. Thiophene monomer was chemically synthesized by an in‐situ oxidation polymerization method. The microwave‐irradiation method was used to form the reduction process of GO. The materials were characterized by scanning electron microscopy, energy dispersive x‐ray analysis, atomic force microscopy, thermogravimetric analysis (TGA) and, differential thermal analysis, Fourier transform infrared spectroscopy, and attenuated total reflectance analysis, Brunauer–Emmett–Teller analysis, four‐point probe conductivity, cyclic voltammetry, galvanostatic charge‐discharge and electrochemical impedance spectroscopy analysis. The TGA analysis shows that PTh has the most degradable material due to small polymer chains. However, the highest thermal stability (98.56%) was obtained for MoS 2 . The temperature raised up to 982°C. Moreover, the highest specific capacitance was calculated as C sp = 1588.72 F/g at 2 mV/s for the rGO/MoS 2 /PTh nanocomposite in a 6 M KOH electrolyte solution. In addition, the highest energy and power densities, specific capacitive retention, and the lowest equivalent series resistance (ESR) were presented for this nanocomposite as E = 3.20 Wh/kg at 10 mA, P = 1152.5 W/kg at 10 mA, 111.48% after 1000 charge–discharge cycles and ESR = 0.05 Ω at 10 mA, respectively. Equivalent ladder circuit model of R s ( C 1 ( R 1 ( R 2 C 2 ))) was also evaluated to interpret theoretical and experimental data using ZSimpWin 3.22 program. Results are compatible with each other. An easy preparation method and eco‐friendly synthesis were reported for rGO/MoS 2 /PTh/CB nanocomposite for next generation supercapacitor evaluations.
- 14 February 2025
- Published by Springer Nature in Ionics
- Vol. 31 (4) , 3697-3714
Facile synthesis of reduced graphene oxide, titanium (IV) oxide, polythiophene, and carbon black nanocomposites and their supercapacitor applications
- 14 February 2025
- Published by Springer Nature in Ionics
- Vol. 31 (4) , 3697-3714
Facile synthesis of reduced graphene oxide, titanium (IV) oxide, polythiophene, and carbon black nanocomposites and their supercapacitor applications
- 26 September 2022
- Published by Springer Nature in Ionics
- Vol. 28 (12) , 5581-5598
Symmetric supercapacitor device applications of rGO / Co3O4 / polypyrrole nanocomposites
- 26 September 2022
- Published by Springer Nature in Ionics
- Vol. 28 (12) , 5581-5598
Symmetric supercapacitor device applications of rGO / Co3O4 / polypyrrole nanocomposites
- 24 May 2021
- Published by Taylor & Francis in Materials Technology
- Vol. 37 (9) , 1168-1182
Binary nanocomposites of reduced graphene oxide and cobalt (II, III) oxide for supercapacitor devices
- 24 May 2021
- Published by Taylor & Francis in Materials Technology
- Vol. 37 (9) , 1168-1182
Binary nanocomposites of reduced graphene oxide and cobalt (II, III) oxide for supercapacitor devices
- 20 February 2019
- Published by SAGE Publications in Plastics, Rubber and Composites: Macromolecular Engineering
- Vol. 48 (4) , 168-184
rGO/CuO/PEDOT nanocomposite formation, its characterisation and electrochemical performances for supercapacitors
Supercapacitor properties of rGO, CuO, PEDOT and rGO/CuO at [rGO]o/[CuO]o = 1:1; 1:1.5; 1:2 and rGO/CuO/PEDOT nanocomposite at [rGO]o/[CuO]o/[EDOT]o = 1:1:1; 1:1:3; 1:1:5 were investigated using chemical reduction of GO and in-situ polymerisation process. SEM-EDX, HRTEM, BET surface area analysis confirm the nanocomposite formations. Nanocomposite materials are also analysed through FTIR-ATR, Raman, TGA-DTA, GCD, CV and EIS. The highest specific capacitance of C sp = 156.7 F/g at 2 mV/s is determined as rGO/CuO/PEDOT at [rGO]o/[CuO]o/[EDOT]o = 1:1:5. In addition, two-electrode supercapacitor device for rGO/CuO/PEDOT at [rGO]o/[CuO]o/[EDOT]o = 1:1:5 are found to provide a maximum specific energy (E = 14.15 Wh/kg at 20 mA) and specific power (P = 24730 W/kg at 50 mA), electrical serial resistance (ESR = 13.33 Ω) with good capacity retention after 3000 cycles. An equivalent circuit model of LR1(CR2)(QR3) is proposed to interpret the EIS data. The supercapacitor performance of the rGO/CuO/PEDOT nanocomposite electrode indicates the synergistic effect of hybrid supercapacitors.
- 20 February 2019
- Published by SAGE Publications in Plastics, Rubber and Composites: Macromolecular Engineering
- Vol. 48 (4) , 168-184
rGO/CuO/PEDOT nanocomposite formation, its characterisation and electrochemical performances for supercapacitors
Supercapacitor properties of rGO, CuO, PEDOT and rGO/CuO at [rGO]o/[CuO]o = 1:1; 1:1.5; 1:2 and rGO/CuO/PEDOT nanocomposite at [rGO]o/[CuO]o/[EDOT]o = 1:1:1; 1:1:3; 1:1:5 were investigated using chemical reduction of GO and in-situ polymerisation process. SEM-EDX, HRTEM, BET surface area analysis confirm the nanocomposite formations. Nanocomposite materials are also analysed through FTIR-ATR, Raman, TGA-DTA, GCD, CV and EIS. The highest specific capacitance of C sp = 156.7 F/g at 2 mV/s is determined as rGO/CuO/PEDOT at [rGO]o/[CuO]o/[EDOT]o = 1:1:5. In addition, two-electrode supercapacitor device for rGO/CuO/PEDOT at [rGO]o/[CuO]o/[EDOT]o = 1:1:5 are found to provide a maximum specific energy (E = 14.15 Wh/kg at 20 mA) and specific power (P = 24730 W/kg at 50 mA), electrical serial resistance (ESR = 13.33 Ω) with good capacity retention after 3000 cycles. An equivalent circuit model of LR1(CR2)(QR3) is proposed to interpret the EIS data. The supercapacitor performance of the rGO/CuO/PEDOT nanocomposite electrode indicates the synergistic effect of hybrid supercapacitors.
- 31 January 2019
- Published by Springer Nature in Journal of Polymer Research
- Vol. 26 (2) , 49
Synthesis of rGO/TiO2/PEDOT nanocomposites, supercapacitor device performances and equivalent electrical circuit models
- 31 January 2019
- Published by Springer Nature in Journal of Polymer Research
- Vol. 26 (2) , 49
Synthesis of rGO/TiO2/PEDOT nanocomposites, supercapacitor device performances and equivalent electrical circuit models