Ping Yang
Ping Yang has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
Shanghua Wu
7 shared publicationsJun Ou
3 shared publicationsShengwu Huang
School of Electromechanical Engineering, Guangdong University of Technology, Guangzhou, China
3 shared publications- Shengwu Huang3 shared publications
- Donglin Lu2 shared publications
Haidong Wu
School of Electromechanical Engineering, Guangdong University of Technology, Guangzhou, China
2 shared publications
Latest Publications
- 12 June 2026
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 37 (17) , 1311
Correction: Effect of diamond particle size on carbothermal reduction behavior and properties of Si3N4 ceramics
- 12 June 2026
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 37 (17) , 1311
Correction: Effect of diamond particle size on carbothermal reduction behavior and properties of Si3N4 ceramics
- 1 June 2025
- Published by SAGE Publications in 3D Printing and Additive Manufacturing
- Vol. 12 (3) , 271-282
Additive Manufacturing of Porous Silicon Nitride Inspired by Triply Periodic Minimal Surface
Triply periodic minimal surface (TPMS) has been widely used in biology due to its excellent biological, controllable mechanical, and material transport properties. In this study, four types of TPMS structures with silicon nitride (Si3N4) ceramic were successfully prepared using digital light processing (DLP) with different minimal surface equations. The influence of different TPMS structures on the mechanical and biological properties of Si3N4 ceramic was systematically investigated. Results indicated a better cell proliferation ability in the D structure compared with three other structures, with favorable compressive strength and Young's modulus of 51.84 ± 8.85 MPa and 3.33 ± 0.08 GPa, respectively.
- 1 June 2025
- Published by SAGE Publications in 3D Printing and Additive Manufacturing
- Vol. 12 (3) , 271-282
Additive Manufacturing of Porous Silicon Nitride Inspired by Triply Periodic Minimal Surface
Triply periodic minimal surface (TPMS) has been widely used in biology due to its excellent biological, controllable mechanical, and material transport properties. In this study, four types of TPMS structures with silicon nitride (Si3N4) ceramic were successfully prepared using digital light processing (DLP) with different minimal surface equations. The influence of different TPMS structures on the mechanical and biological properties of Si3N4 ceramic was systematically investigated. Results indicated a better cell proliferation ability in the D structure compared with three other structures, with favorable compressive strength and Young's modulus of 51.84 ± 8.85 MPa and 3.33 ± 0.08 GPa, respectively.
- 16 August 2024
- Published by Elsevier in Ceramics International
- Vol. 50 (21) , 44175-44185
Preparation of high-strength ZrO2 ceramics by binder jetting additive manufacturing and liquid glass infiltration
- 16 August 2024
- Published by Elsevier in Ceramics International
- Vol. 50 (21) , 44175-44185
Preparation of high-strength ZrO2 ceramics by binder jetting additive manufacturing and liquid glass infiltration
- 4 May 2023
- Published by Elsevier in Ceramics International
- Vol. 49 (15) , 25025-25034
Additive manufacturing of complex-shaped and porous silicon nitride-based components for bionic bones
- 4 May 2023
- Published by Elsevier in Ceramics International
- Vol. 49 (15) , 25025-25034
Additive manufacturing of complex-shaped and porous silicon nitride-based components for bionic bones
- 10 December 2022
- Published by Elsevier in Ceramics International
- Vol. 49 (8) , 12166-12172
Cure behaviour and mechanical properties of Si3N4 ceramics with bimodal particle size distribution prepared using digital light processing
- 10 December 2022
- Published by Elsevier in Ceramics International
- Vol. 49 (8) , 12166-12172
Cure behaviour and mechanical properties of Si3N4 ceramics with bimodal particle size distribution prepared using digital light processing
- 22 March 2022
- Published by Elsevier in Ceramics International
- Vol. 48 (13) , 18615-18624
Enhanced thermal conductivity in Si3N4 ceramics by carbonizing polydopamine coatings
- 22 March 2022
- Published by Elsevier in Ceramics International
- Vol. 48 (13) , 18615-18624
Enhanced thermal conductivity in Si3N4 ceramics by carbonizing polydopamine coatings
- 20 January 2022
- Published by Elsevier in Ceramics International
- Vol. 48 (9) , 12569-12577
Improving cure performance of Si3N4 suspension with a high refractive index resin for stereolithography-based additive manufacturing
- 20 January 2022
- Published by Elsevier in Ceramics International
- Vol. 48 (9) , 12569-12577
Improving cure performance of Si3N4 suspension with a high refractive index resin for stereolithography-based additive manufacturing
- Open Access
- 2 January 2022
- Published by Taylor & Francis in Journal of Asian Ceramic Societies
- Vol. 10 (1) , 69-82
Digital light processing 3D printing of surface-oxidized Si3N4 coated by silane coupling agent
Due to high light absorption and high refractive index of silicon nitride (Si3N4) ceramic, it is difficult to prepare Si3N4 slurry with favorable curing ability, high solid loading and low viscosity at the same time, and thus the high-quality Si3N4 parts are hard to fabricate via Digital Light Processing (DLP). In this paper, the oxidation process was used to enhance the curing behavior of Si3N4 slurry, and then silane coupling agent (KH560) was used to improve the rheological properties of the oxidized Si3N4 slurry. The effect of Si3N4 slurry with oxidation and modification on its rheological behavior, light absorption, curing ability and stability have been systematically investigated. A Si3N4 slurry with abundant photocuring ability, high solid loading, low viscosity and reliable stability was fabricated by the oxidized (1 h) and KH560 (1 wt.%) modified Si3N4 powders, and the dense Si3N4 ceramic parts were produced by this slurry via DLP 3D printing. Subsequently, the influence of oxidation and modification on microstructure, mechanical properties and thermal conductivity have been investigated. Finally, the microstructure and performances of Si3N4 ceramic were compared between different forming processes (including: DLP and cool isostatic pressing).
- 2 January 2022
- Published by Taylor & Francis in Journal of Asian Ceramic Societies
- Vol. 10 (1) , 69-82
Open AccessDigital light processing 3D printing of surface-oxidized Si3N4 coated by silane coupling agent
Due to high light absorption and high refractive index of silicon nitride (Si3N4) ceramic, it is difficult to prepare Si3N4 slurry with favorable curing ability, high solid loading and low viscosity at the same time, and thus the high-quality Si3N4 parts are hard to fabricate via Digital Light Processing (DLP). In this paper, the oxidation process was used to enhance the curing behavior of Si3N4 slurry, and then silane coupling agent (KH560) was used to improve the rheological properties of the oxidized Si3N4 slurry. The effect of Si3N4 slurry with oxidation and modification on its rheological behavior, light absorption, curing ability and stability have been systematically investigated. A Si3N4 slurry with abundant photocuring ability, high solid loading, low viscosity and reliable stability was fabricated by the oxidized (1 h) and KH560 (1 wt.%) modified Si3N4 powders, and the dense Si3N4 ceramic parts were produced by this slurry via DLP 3D printing. Subsequently, the influence of oxidation and modification on microstructure, mechanical properties and thermal conductivity have been investigated. Finally, the microstructure and performances of Si3N4 ceramic were compared between different forming processes (including: DLP and cool isostatic pressing).
- 1 September 2021
- Published by Elsevier in Ceramics International
- Vol. 47 (17) , 23919-23926
Prediction of bending strength of Si3N4 using machine learning
- 1 September 2021
- Published by Elsevier in Ceramics International
- Vol. 47 (17) , 23919-23926
Prediction of bending strength of Si3N4 using machine learning
- Open Access
- 11 August 2021
- Published by Springer Nature in Research Square
Digital Light Processing 3D Printing of Surface-oxidized Si3N4 Coated by Silane Coupling Agent
Due to high light absorption and high refractive index of silicon nitride (Si3N4) ceramic, it is difficult to prepare Si3N4 slurry with favourable curing ability, high solid loading and low viscosity at the same time, and thus the high quality Si3N4 parts are hard to fabricate via Digital Light Processing (DLP). In this paper, oxidation process was used to enhance the curing behavior of Si3N4 slurry, and then silane coupling agent (KH560) was used to improve the rheological properties of the oxidized Si3N4 slurry. The effect of Si3N4 slurry with oxidation and modification on its rheological behavior, light absorption, curing ability and stability have been systematically investigated. A Si3N4 slurry with abundant photocuring ability, high solid loading, low viscosity and reliable stability was fabricated by the oxidized (1h) and KH560 (1wt.%) modified Si3N4 powders, and the dense Si3N4 ceramic parts were produced by this slurry via DLP 3D printing. Subsequently, the influence of oxidation and modification on microstructure, mechanical properties and thermal conductivity have been investigated. Finally, the performances of the DLP 3D printed samples are close to the isostatic cool pressing (ICP) fabricated samples. Consequently, DLP has well potential to fabricate high-performance Si3N4 ceramics.
- 11 August 2021
- Published by Springer Nature in Research Square
Open AccessDigital Light Processing 3D Printing of Surface-oxidized Si3N4 Coated by Silane Coupling Agent
Due to high light absorption and high refractive index of silicon nitride (Si3N4) ceramic, it is difficult to prepare Si3N4 slurry with favourable curing ability, high solid loading and low viscosity at the same time, and thus the high quality Si3N4 parts are hard to fabricate via Digital Light Processing (DLP). In this paper, oxidation process was used to enhance the curing behavior of Si3N4 slurry, and then silane coupling agent (KH560) was used to improve the rheological properties of the oxidized Si3N4 slurry. The effect of Si3N4 slurry with oxidation and modification on its rheological behavior, light absorption, curing ability and stability have been systematically investigated. A Si3N4 slurry with abundant photocuring ability, high solid loading, low viscosity and reliable stability was fabricated by the oxidized (1h) and KH560 (1wt.%) modified Si3N4 powders, and the dense Si3N4 ceramic parts were produced by this slurry via DLP 3D printing. Subsequently, the influence of oxidation and modification on microstructure, mechanical properties and thermal conductivity have been investigated. Finally, the performances of the DLP 3D printed samples are close to the isostatic cool pressing (ICP) fabricated samples. Consequently, DLP has well potential to fabricate high-performance Si3N4 ceramics.