Angel Rodríguez Soto
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Angel Rodríguez Soto has a total of 55 co-authors. Here are the top co-authors by number of shared publications:
- José Luis Valin Rivera
Escuela de Ingeniería Mecánica, Facultad de Ingeniería, Pontificia Universidad Católica de Valparaíso, Avenida Brasil 2950, Valparaíso 2340025, Chile
5 shared publications - Yunesky Masip Macia
Escuela de Ingeniería Mecánica, Pontificia Universidad Católica de Valparaíso, Valparaíso 2340025, Chile
5 shared publications - Gilberto Garcia del Pino
Departamento de Engenharia Mecânica, Universidade do Estado do Amazonas (UEA), Manaus 69050-020, Amazonas, Brazil
4 shared publications - Juan Enrique Palomares Ruiz
Postgraduate and Research Subdirection, Tecnológico Nacional de México/ITS de Cajeme-ULSA Noroeste, Ciudad Obregón 85024, Mexico
4 shared publications - Meylí Valin Fernández
Department of Mechanical Engineering (DIM), Faculty of Engineering (FI), Universidad de Concepción, Concepción 4030000, Chile
4 shared publications - Pablo Rodriguez
Departamento de Geografía, Facultad de Ingeniería, Universidad de Santiago de Chile, Santiago de Chile 9170020, Chile
4 shared publications
Latest Publications
- Open Access
- 17 October 2023
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 50, 578-598
Parameterization proposal to determine the feasibility of geographic areas for the green hydrogen industry under socio-environmental and technical constraints in Chile
- 17 October 2023
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 50, 578-598
Open AccessParameterization proposal to determine the feasibility of geographic areas for the green hydrogen industry under socio-environmental and technical constraints in Chile
- Open Access
Influence of Bentonite Particles on the Mechanical Properties of Polyester–Sisal Fiber Composites
As a part of the mission to create materials that are more environmentally friendly, we present the following proposal, in which a study of the mechanical properties of composite materials comprising a polyester resin with sisal fiber and bentonite particles was conducted. Sisal fiber was added to a matrix in percentages ranging from 5% to 45% in relation to the polyester resin weight, while bentonite remained fixed at 7% in relation to the polyester resin weight. The specimens were manufactured by compression molding. The mechanical properties were analyzed by tensile, bending, impact, stepped creep, and relaxation tests. In addition, energy-dispersive X-ray spectroscopy and scanning electron microscopy analyses were carried out to analyze the composition and heterogeneity of the structure of the composite material. The results obtained showed that 7% of bentonite added to the matrix affects the tensile strength. Flexural strength increased by up to 21% in the specimens with a 20% addition of sisal fiber, while the elastic modulus increased by up to 43% in the case of a 20% addition of sisal fiber. The viscoelastic behavior was improved, while the relaxation stress was affected.
Open AccessInfluence of Bentonite Particles on the Mechanical Properties of Polyester–Sisal Fiber Composites
As a part of the mission to create materials that are more environmentally friendly, we present the following proposal, in which a study of the mechanical properties of composite materials comprising a polyester resin with sisal fiber and bentonite particles was conducted. Sisal fiber was added to a matrix in percentages ranging from 5% to 45% in relation to the polyester resin weight, while bentonite remained fixed at 7% in relation to the polyester resin weight. The specimens were manufactured by compression molding. The mechanical properties were analyzed by tensile, bending, impact, stepped creep, and relaxation tests. In addition, energy-dispersive X-ray spectroscopy and scanning electron microscopy analyses were carried out to analyze the composition and heterogeneity of the structure of the composite material. The results obtained showed that 7% of bentonite added to the matrix affects the tensile strength. Flexural strength increased by up to 21% in the specimens with a 20% addition of sisal fiber, while the elastic modulus increased by up to 43% in the case of a 20% addition of sisal fiber. The viscoelastic behavior was improved, while the relaxation stress was affected.
- Open Access
Effect of Nanometric Particles of Bentonite on the Mechanical Properties of a Thermoset Polymeric Matrix Reinforced with Hemp Fibers
The influence of the addition of bentonite nanoparticles on the tensile and flexural strength of a thermosetting polymer matrix composite material reinforced with hemp fibers was de-terminated. All composites were manufactured with 5% of bentonite in the polymer mass–weight ratios and 10 to 45 wt% of fibers with a step of 5%. For mechanical characterization, tensile and flexural tests were performed: scanning electron microscopy and energy-dispersive X-ray spectroscopy analyses were carried out. The tensile strength of the samples containing bentonite compared to the polymer samples with the fiber addition was affected for all fiber addition percentages, except for 35% while the flexural resistance improved with the addition of bentonite in the percentages of 20, 30, 35, and 45% of fiber addition. With the addition of bentonite, the maximum values of tensile and flexural strength were both obtained for the 35% addition of fibers, with values of 34.28 MPa and 98.04 MPa, respectively. The presence of bentonite favored the rigidity of the material to traction and bending, which was reflected through an increase in the elastic modulus compared to the composite that only had fiber. The maximum values obtained were 9065 MPa in tension and 8453 MPa in flexion for the 40% and 35% of addition of fiber, respectively. Microscopy showed a good distribution of fibers in the matrix, the absence of internal porosities, and a good interaction between matrix and reinforcement.
Open AccessEffect of Nanometric Particles of Bentonite on the Mechanical Properties of a Thermoset Polymeric Matrix Reinforced with Hemp Fibers
The influence of the addition of bentonite nanoparticles on the tensile and flexural strength of a thermosetting polymer matrix composite material reinforced with hemp fibers was de-terminated. All composites were manufactured with 5% of bentonite in the polymer mass–weight ratios and 10 to 45 wt% of fibers with a step of 5%. For mechanical characterization, tensile and flexural tests were performed: scanning electron microscopy and energy-dispersive X-ray spectroscopy analyses were carried out. The tensile strength of the samples containing bentonite compared to the polymer samples with the fiber addition was affected for all fiber addition percentages, except for 35% while the flexural resistance improved with the addition of bentonite in the percentages of 20, 30, 35, and 45% of fiber addition. With the addition of bentonite, the maximum values of tensile and flexural strength were both obtained for the 35% addition of fibers, with values of 34.28 MPa and 98.04 MPa, respectively. The presence of bentonite favored the rigidity of the material to traction and bending, which was reflected through an increase in the elastic modulus compared to the composite that only had fiber. The maximum values obtained were 9065 MPa in tension and 8453 MPa in flexion for the 40% and 35% of addition of fiber, respectively. Microscopy showed a good distribution of fibers in the matrix, the absence of internal porosities, and a good interaction between matrix and reinforcement.
- Open Access
- 19 February 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (4) , 2677
Mechanical Characterization of a Polymer/Natural Fibers/Bentonite Composite Material with Implementation of a Continuous Damage Model
A characterization of composite materials of a polyester matrix reinforced with natural fibers of Cuban henequen and organophilized Cuban bentonite was carried out, the experimental results of which are used to formulate, implement, and validate a scalar damage model. The fibers were added on a weight basis of 15, 20, and 25% as a reinforcing material, and organophilized Cuban bentonite, in amounts of 3, 5, and 7% by weight, was added. Samples containing only polymer and fibers showed the best mechanical performance for 25% of fiber, with increases of 51% in the tensile strength and 169% on the impact resistance. Samples containing polymer and clay showed the best results for 5% of bentonite, with increases of 89% in the tensile strength and 83% on the impact resistance, and samples containing 25% fiber and 5% clay were also prepared and achieved a 98% increase in the tensile strength and 219% in the impact strength. The scalar damage model deals with an internal variable, which corresponds to the damage variable, together with a failure surface that allows identifying the mechanical state of the material dependent on the mechanical stress, obtaining an adequate correlation with the results of the experimental tests.
- 19 February 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (4) , 2677
Open AccessMechanical Characterization of a Polymer/Natural Fibers/Bentonite Composite Material with Implementation of a Continuous Damage Model
A characterization of composite materials of a polyester matrix reinforced with natural fibers of Cuban henequen and organophilized Cuban bentonite was carried out, the experimental results of which are used to formulate, implement, and validate a scalar damage model. The fibers were added on a weight basis of 15, 20, and 25% as a reinforcing material, and organophilized Cuban bentonite, in amounts of 3, 5, and 7% by weight, was added. Samples containing only polymer and fibers showed the best mechanical performance for 25% of fiber, with increases of 51% in the tensile strength and 169% on the impact resistance. Samples containing polymer and clay showed the best results for 5% of bentonite, with increases of 89% in the tensile strength and 83% on the impact resistance, and samples containing 25% fiber and 5% clay were also prepared and achieved a 98% increase in the tensile strength and 219% in the impact strength. The scalar damage model deals with an internal variable, which corresponds to the damage variable, together with a failure surface that allows identifying the mechanical state of the material dependent on the mechanical stress, obtaining an adequate correlation with the results of the experimental tests.
- Open Access
Parameter Identification of Fractional Index Viscoelastic Model for Vegetable-Fiber Reinforced Composite
In the present work, parameters for adapting the behavior of the uniaxial three-element viscoelastic constitutive model with integer and fractional index derivatives to the mechanical evolution of an epoxy-composite material reinforced with long random henequen fibers, were determined. Cyclic loading–unloading with , , , …, controlled strain and staggered fluency experiments at 5 MPa, 10 MPa, and 15 MPa constant tension were performed in stages, and the obtained data were used to determine and validate the model’s parameter values. The Inverse Method of Identification was used to calculate the parameters, and the Particle Swarm Optimization (PSO) method was employed to achieve minimization of the error function. A comparison between the simulated uniaxial results and the experimental data is demonstrated graphically. There exists a strong dependence between properties of the composite and the fiber content (0 wt%, 9 wt%, 14 wt%, 22 wt%, and 28 wt% weight percentage fiber/matrix), and therefore also of the model parameter values. Both uniaxial models follow the viscoelastic behavior of the material and the fractional index version presents the best accuracy. The latter method was noted to be adequate for determination of the aforementioned constants using non-large experimental data and procedures that are easy to implement.Open AccessParameter Identification of Fractional Index Viscoelastic Model for Vegetable-Fiber Reinforced Composite
In the present work, parameters for adapting the behavior of the uniaxial three-element viscoelastic constitutive model with integer and fractional index derivatives to the mechanical evolution of an epoxy-composite material reinforced with long random henequen fibers, were determined. Cyclic loading–unloading with , , , …, controlled strain and staggered fluency experiments at 5 MPa, 10 MPa, and 15 MPa constant tension were performed in stages, and the obtained data were used to determine and validate the model’s parameter values. The Inverse Method of Identification was used to calculate the parameters, and the Particle Swarm Optimization (PSO) method was employed to achieve minimization of the error function. A comparison between the simulated uniaxial results and the experimental data is demonstrated graphically. There exists a strong dependence between properties of the composite and the fiber content (0 wt%, 9 wt%, 14 wt%, 22 wt%, and 28 wt% weight percentage fiber/matrix), and therefore also of the model parameter values. Both uniaxial models follow the viscoelastic behavior of the material and the fractional index version presents the best accuracy. The latter method was noted to be adequate for determination of the aforementioned constants using non-large experimental data and procedures that are easy to implement. - Open Access
- 16 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 10, 103749-103764
Parametric Study of Electronic Cooling by Means of a Combination of Crossflow and an Impinging Jet
This paper reports a parametric study’s experimental results based on the experiments’ design. No works in the literature have investigated parametrically experimental effects on electronic component cooling by combining an impinging jet and a channel flow configuration on the cooling of electronic components. This study analyzed five parameters experimentally to enhance the cooling process using statistical techniques. Additionally, the optimal configuration determined for the conventional cooling method using only the channel flow was compared. Three parameters are associated with the geometric configuration (height of the electronic component $h/H = 1/6, 1/3$ , 1/2, jet diameter $D/H = 0.3, 0.4$ , 0.5 and jet-component eccentricity $S/H = 0, 1/8$ , 1/4), and the other two are related to the fluid flow (the Reynolds number based on the channel height and mean velocity of the stream $Re_{H}= 3410$ , 4205, 5000 and the ratio between the jet and the channel mean velocities $U_{j}/U_{m}= 2.5$ , 3.75, 5). The results show that the main parameters are statistically significant relative to heat transfer, with $Re_{H}$ , $U_{j}/U_{m}$ and $h/H$ displaying the most significant amplitude of variation in response and increasing the Nusselt number by approximately 60%. The surface response models have shown a satisfactory fit with the experimental data, allowing, in a preliminary way, the minimum mechanical energy loss requirement to be identified to maximize up to 160% of the heat transfer. Specifically, the heat transfer enhancement is more significant for components of considerable height than other components. Heat transfer enhancement occurs at low mechanical energy loss when the velocity ratio decreases at the minimum channel Reynolds number at the maximum jet diameter and jet-component eccentricity.
- 16 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 10, 103749-103764
Open AccessParametric Study of Electronic Cooling by Means of a Combination of Crossflow and an Impinging Jet
This paper reports a parametric study’s experimental results based on the experiments’ design. No works in the literature have investigated parametrically experimental effects on electronic component cooling by combining an impinging jet and a channel flow configuration on the cooling of electronic components. This study analyzed five parameters experimentally to enhance the cooling process using statistical techniques. Additionally, the optimal configuration determined for the conventional cooling method using only the channel flow was compared. Three parameters are associated with the geometric configuration (height of the electronic component $h/H = 1/6, 1/3$ , 1/2, jet diameter $D/H = 0.3, 0.4$ , 0.5 and jet-component eccentricity $S/H = 0, 1/8$ , 1/4), and the other two are related to the fluid flow (the Reynolds number based on the channel height and mean velocity of the stream $Re_{H}= 3410$ , 4205, 5000 and the ratio between the jet and the channel mean velocities $U_{j}/U_{m}= 2.5$ , 3.75, 5). The results show that the main parameters are statistically significant relative to heat transfer, with $Re_{H}$ , $U_{j}/U_{m}$ and $h/H$ displaying the most significant amplitude of variation in response and increasing the Nusselt number by approximately 60%. The surface response models have shown a satisfactory fit with the experimental data, allowing, in a preliminary way, the minimum mechanical energy loss requirement to be identified to maximize up to 160% of the heat transfer. Specifically, the heat transfer enhancement is more significant for components of considerable height than other components. Heat transfer enhancement occurs at low mechanical energy loss when the velocity ratio decreases at the minimum channel Reynolds number at the maximum jet diameter and jet-component eccentricity.
- Open Access
- 4 July 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (13) , 6768
The Restored Premolars Biomechanical Behavior: FEM and Experimental Moiré Analyses
This study applied the finite element method (FEM) and the moiré strip projection method to evaluate the biomechanical behavior of healthy and endodontic-treated premolar teeth. The finite element method and the moiré strip projection method were applied to evaluate the influence of restored materials in association with cervical lesions and were considered as strain estimates for a tooth sample with 21 units, under loads of 25, 50, 75, and 100 N, frontal and oblique applied. The focused cases were: tooth H healthy; tooth A-MOD amalgam; tooth AL-MOD amalgam + lesion; tooth ALR-MOD amalgam + injury restored; tooth R-MOD resin; tooth RL-MOD resin + lesion; tooth RLR-MOD resin + injury restored. The results obtained by FEM simulation can be considered perfectly validated by the results presented by the experimental moiré projection analysis, demonstrating that the FEM numerical analysis can be used to evaluate the biomechanical behavior of healthy and endodontically treated teeth. Developing an alternative protocol to generate FEM three-dimensional models will lead to a ready and inexpensive tool since there is no need for costly equipment for tooth extraction prognosis.
- 4 July 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (13) , 6768
Open AccessThe Restored Premolars Biomechanical Behavior: FEM and Experimental Moiré Analyses
This study applied the finite element method (FEM) and the moiré strip projection method to evaluate the biomechanical behavior of healthy and endodontic-treated premolar teeth. The finite element method and the moiré strip projection method were applied to evaluate the influence of restored materials in association with cervical lesions and were considered as strain estimates for a tooth sample with 21 units, under loads of 25, 50, 75, and 100 N, frontal and oblique applied. The focused cases were: tooth H healthy; tooth A-MOD amalgam; tooth AL-MOD amalgam + lesion; tooth ALR-MOD amalgam + injury restored; tooth R-MOD resin; tooth RL-MOD resin + lesion; tooth RLR-MOD resin + injury restored. The results obtained by FEM simulation can be considered perfectly validated by the results presented by the experimental moiré projection analysis, demonstrating that the FEM numerical analysis can be used to evaluate the biomechanical behavior of healthy and endodontically treated teeth. Developing an alternative protocol to generate FEM three-dimensional models will lead to a ready and inexpensive tool since there is no need for costly equipment for tooth extraction prognosis.