Satoshi Inaba
Research Subjects
Research Interests
Satoshi Inaba has a total of 213 co-authors. Here are the top co-authors by number of shared publications:
Y. Toyoshima
Toshiba Corporation, 8, Shinsugita-cho, Isogo-ku, Yokohama, Kanagawa 235-8522 Japan
15 shared publicationsH. Ishiuchi
Center for Semiconductor Research and Development, Toshiba Corporation Semiconductor Company, 8 Shinsugita-cho, Isogo-ku, Yokohama 235-8522, Japan. Phone: +81-45-770-3661 Fax: +81-45-770-3577
13 shared publicationsK. Okano
Toshiba Corporation, 8, Shinsugita-cho, Isogo-ku, Yokohama, Kanagawa 235-8522 Japan
13 shared publicationsK. Ishimaru
Toshiba America Electronic Components Inc., Yorktown Heights, NY, USA
12 shared publicationsN. Aoki
12 shared publicationsK. Suguro
Center for Semiconductor Research and Development & Manufacturing Engineering Center, Toshiba Corporation Semiconductor Company, 8, Shin sugita-cho, Isogo-ku, Yokohama, 235-8522, Japan;Toshiba America Electronic Components Inc., Yorktown Heights, NY, USA
10 shared publications
Latest Publications
- 1 May 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
3D Flash Memory for Data-Intensive Applications
In this review paper, the advantages in latest 3D Flash memory are discussed from the viewpoints of Scalability, Reliability, and Efficiency for the Data-intensive applications. By a lot of recent improvements in fabrication process and circuit design, 3D Flash memory offers unique solution for future high-performance data storage.
- 1 May 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
3D Flash Memory for Data-Intensive Applications
In this review paper, the advantages in latest 3D Flash memory are discussed from the viewpoints of Scalability, Reliability, and Efficiency for the Data-intensive applications. By a lot of recent improvements in fabrication process and circuit design, 3D Flash memory offers unique solution for future high-performance data storage.
- 22 September 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
Foreword
On behalf of the organizing committees, it is our pleasure to welcome you to the 36th Symposium on VLSI Technology to be held June 13 – 16, 2016, at the Hilton Hawaiian Village in Honolulu, Hawaii. Since its founding in 1982, the Symposium, jointly sponsored by the IEEE Electron Devices Society and the Japan Society of Applied Physics, has been recognized as one of the premiere international conferences on VLSI & Semiconductor technology. As always, the latest technology advancements in semiconductors will be shared by leading technologists from industry and academia this year too.
- 22 September 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
Foreword
On behalf of the organizing committees, it is our pleasure to welcome you to the 36th Symposium on VLSI Technology to be held June 13 – 16, 2016, at the Hilton Hawaiian Village in Honolulu, Hawaii. Since its founding in 1982, the Symposium, jointly sponsored by the IEEE Electron Devices Society and the Japan Society of Applied Physics, has been recognized as one of the premiere international conferences on VLSI & Semiconductor technology. As always, the latest technology advancements in semiconductors will be shared by leading technologists from industry and academia this year too.
- 1 January 2015
- Published by Institute of Electronics, Information and Communications Engineers (IEICE) in IEICE Transactions on Electronics
- Vol. E98.C  (6) , 455-460
Technology of FinFET for High RF and Analog/Mixed-Signal Performance Circuits
- 1 January 2015
- Published by Institute of Electronics, Information and Communications Engineers (IEICE) in IEICE Transactions on Electronics
- Vol. E98.C  (6) , 455-460
Technology of FinFET for High RF and Analog/Mixed-Signal Performance Circuits
- 1 June 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 07431562,p. 149-150
The optimum device parameters for high RF and analog/MS performance in planar MOSFET and FinFET
In planar MOSFET, the optimization of finger length should be carried out with considering f T , f max and flicker noise because the noise degradation at STI edge effect appears below 1μm. In FinFET, the optimization of not only finger length but also the distance between gate and source, drain contact region and fin pitch are necessary to reduce parasitic resistance and capacitance. According to our measurement results, the flicker noise of FinFET decreases with scaling of fin width and it is possible to satisfy the 24nm technology node requirement in ITRS roadmap 2011 at fin width below 20nm.
- 1 June 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 07431562,p. 149-150
The optimum device parameters for high RF and analog/MS performance in planar MOSFET and FinFET
In planar MOSFET, the optimization of finger length should be carried out with considering f T , f max and flicker noise because the noise degradation at STI edge effect appears below 1μm. In FinFET, the optimization of not only finger length but also the distance between gate and source, drain contact region and fin pitch are necessary to reduce parasitic resistance and capacitance. According to our measurement results, the flicker noise of FinFET decreases with scaling of fin width and it is possible to satisfy the 24nm technology node requirement in ITRS roadmap 2011 at fin width below 20nm.
- 3 October 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 58  (11) , 3778-3786
Mechanism of Contact Resistance Reduction in Nickel Silicide Films by Pt Incorporation
Platinum (Pt) incorporation into nickel silicide (NiSi) films improves silicide characteristics such as lower contact resistance RC at silicide/Si interface and higher thermal stability. The impact of Pt incorporation is widely accepted and recognized in research field; however, the role of Pt in NiSi films has not been fully clarified so far. In this paper, the spatial distributions of Pt and dopants (i.e., arsenic and boron) in silicide films are studied at an atomic level analysis using local electrode atom probe. In particular, Pt and dopant distributions were investigated in detail both at silicide/Si interface and at silicide-grain boundary. Silicide-grain size was also analyzed at various Pt concentrations in silicide films, and the relationship between the Pt concentration and physical properties of Ni1-xPtxSi films is pointed out. Finally, for further CMOS device scaling, the benefit of higher concentration of Pt incorporation into Ni1-xPtxSi films is described.
- 3 October 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 58  (11) , 3778-3786
Mechanism of Contact Resistance Reduction in Nickel Silicide Films by Pt Incorporation
Platinum (Pt) incorporation into nickel silicide (NiSi) films improves silicide characteristics such as lower contact resistance RC at silicide/Si interface and higher thermal stability. The impact of Pt incorporation is widely accepted and recognized in research field; however, the role of Pt in NiSi films has not been fully clarified so far. In this paper, the spatial distributions of Pt and dopants (i.e., arsenic and boron) in silicide films are studied at an atomic level analysis using local electrode atom probe. In particular, Pt and dopant distributions were investigated in detail both at silicide/Si interface and at silicide-grain boundary. Silicide-grain size was also analyzed at various Pt concentrations in silicide films, and the relationship between the Pt concentration and physical properties of Ni1-xPtxSi films is pointed out. Finally, for further CMOS device scaling, the benefit of higher concentration of Pt incorporation into Ni1-xPtxSi films is described.
- 1 July 2011
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 50  (7R)
Thermal-Annealing Effects on Dopant Redistribution in Nanoscale Si Fin
We investigated the diffusion of implanted boron and phosphorous in a narrow Si fin during rapid thermal annealing (RTA) at 1000 °C for 10 s. We found that the boron diffusion is described by the conventional diffusion model. We also found that the point defects (interstitial Si and vacancy) play an important role in determining the detailed distribution of boron in a narrow Si fin. On the other hand, the phosphorous diffusion shows anomalous behavior in the peak region of the Si fin, namely large dose loss from the Si region. We found experimentally that about 50% of implanted phosphorous atoms in the Si fin diffused out from the Si region by the annealing (1000 °C, 10 s). The simulation result shows that the experimental result of phosphorous diffusion is reproduced by taking into account the dose loss model through introduction of the interfacial trap layer. Because the phosphorous distribution is largely modified by the dose loss effect, it is considered that the large dose loss of phosphorous gives rise to large impacts on the device characteristics of fin field effect transistors (FinFETs).
- 1 July 2011
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 50  (7R)
Thermal-Annealing Effects on Dopant Redistribution in Nanoscale Si Fin
We investigated the diffusion of implanted boron and phosphorous in a narrow Si fin during rapid thermal annealing (RTA) at 1000 °C for 10 s. We found that the boron diffusion is described by the conventional diffusion model. We also found that the point defects (interstitial Si and vacancy) play an important role in determining the detailed distribution of boron in a narrow Si fin. On the other hand, the phosphorous diffusion shows anomalous behavior in the peak region of the Si fin, namely large dose loss from the Si region. We found experimentally that about 50% of implanted phosphorous atoms in the Si fin diffused out from the Si region by the annealing (1000 °C, 10 s). The simulation result shows that the experimental result of phosphorous diffusion is reproduced by taking into account the dose loss model through introduction of the interfacial trap layer. Because the phosphorous distribution is largely modified by the dose loss effect, it is considered that the large dose loss of phosphorous gives rise to large impacts on the device characteristics of fin field effect transistors (FinFETs).
- 7 April 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 58  (5) , 1302-1310
25-nm Gate Length nMOSFET With Steep Channel Profiles Utilizing Carbon-Doped Silicon Layers (A P-Type Dopant Confinement Layer)
Steep channel profiles of scaled transistors are a promising approach for advancing transistor generation in bulk complementary metal-oxide-semiconductor (MOS). In this paper, a carbon-doped Si (Si:C) layer under an undoped Si layer is proposed to form steep p-type channel profiles in n-channel MOS field-effect transistors (nMOSFETs) due to extremely low diffusivity of boron and indium in Si:C layers. This structure with low channel impurity improves mobility and suppresses threshold voltage (VTH) variation. Both items are essential for aggressively scaled MOSFETs with a gate length less than 25 nm. We demonstrated well-controlled, high-performance, and low VTH variability nMOSFETs with a Si:C-Si epitaxial channel structure.
- 7 April 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 58  (5) , 1302-1310
25-nm Gate Length nMOSFET With Steep Channel Profiles Utilizing Carbon-Doped Silicon Layers (A P-Type Dopant Confinement Layer)
Steep channel profiles of scaled transistors are a promising approach for advancing transistor generation in bulk complementary metal-oxide-semiconductor (MOS). In this paper, a carbon-doped Si (Si:C) layer under an undoped Si layer is proposed to form steep p-type channel profiles in n-channel MOS field-effect transistors (nMOSFETs) due to extremely low diffusivity of boron and indium in Si:C layers. This structure with low channel impurity improves mobility and suppresses threshold voltage (VTH) variation. Both items are essential for aggressively scaled MOSFETs with a gate length less than 25 nm. We demonstrated well-controlled, high-performance, and low VTH variability nMOSFETs with a Si:C-Si epitaxial channel structure.
- 1 April 2011
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 50  (4S) , 04DC15
Advantage of Plasma Doping for Source/Drain Extension in Bulk Fin Field Effect Transistor
The impact of plasma doping (PD) on the formation of source/drain extension (SDE) is demonstrated for a p-type bulk fin field effect transistor (FinFET). The impurity distribution in a narrow fin (15 nm) was analyzed with atom probe tomography (APT) and secondary ion mass spectroscopy (SIMS). The lateral distribution of boron in the Si fin by the PD is similar to the case with conventional beam-line ion implantation (BL). However, the vertical distribution of boron by the PD is much steeper than that by the conventional BL. TCAD simulations show that the driving current of the FinFET fabricated by the PD is 34% higher than that of the FinFET fabricated by the BL under the same off-leakage current. Therefore, the PD is a key technology for fabricating the SDE of narrow bulk-FinFETs in the future.
- 1 April 2011
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 50  (4S) , 04DC15
Advantage of Plasma Doping for Source/Drain Extension in Bulk Fin Field Effect Transistor
The impact of plasma doping (PD) on the formation of source/drain extension (SDE) is demonstrated for a p-type bulk fin field effect transistor (FinFET). The impurity distribution in a narrow fin (15 nm) was analyzed with atom probe tomography (APT) and secondary ion mass spectroscopy (SIMS). The lateral distribution of boron in the Si fin by the PD is similar to the case with conventional beam-line ion implantation (BL). However, the vertical distribution of boron by the PD is much steeper than that by the conventional BL. TCAD simulations show that the driving current of the FinFET fabricated by the PD is 34% higher than that of the FinFET fabricated by the BL under the same off-leakage current. Therefore, the PD is a key technology for fabricating the SDE of narrow bulk-FinFETs in the future.
- 1 April 2011
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 50  (4S) , 04DC08
High-Temperature Properties of Drain Current Variability in Scaled Field-Effect Transistors Analyzed by Decomposition Method
The properties of drain current variability in field-effect transistors (FETs) at high temperature are experimentally investigated. It is found that the on-state drain current (I ON) at high temperature has a strong correlation with I ON at room temperature and that there is no anomalous I ON change from room temperature to high temperature. It is also found that I ON variability at high temperature is smaller than that at room temperature. The origin of the decrease in I ON variability with increasing temperature is analyzed by the decomposition method developed in our previous work. It is clarified that the decrease in the current–onset voltage component plays a dominant role, especially in the saturation region. Moreover, it is also clarified that thermal excitation of carriers suppresses current–onset voltage variability, and ultimately the current–onset voltage component of I ON variability with increasing temperature.
- 1 April 2011
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 50  (4S) , 04DC08
High-Temperature Properties of Drain Current Variability in Scaled Field-Effect Transistors Analyzed by Decomposition Method
The properties of drain current variability in field-effect transistors (FETs) at high temperature are experimentally investigated. It is found that the on-state drain current (I ON) at high temperature has a strong correlation with I ON at room temperature and that there is no anomalous I ON change from room temperature to high temperature. It is also found that I ON variability at high temperature is smaller than that at room temperature. The origin of the decrease in I ON variability with increasing temperature is analyzed by the decomposition method developed in our previous work. It is clarified that the decrease in the current–onset voltage component plays a dominant role, especially in the saturation region. Moreover, it is also clarified that thermal excitation of carriers suppresses current–onset voltage variability, and ultimately the current–onset voltage component of I ON variability with increasing temperature.
- 1 December 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 01631918,p. 3.5.1-3.5.4
Impact of DIBL variability on SRAM static noise margin analyzed by DMA SRAM TEG
The static noise margin (SNM) as well as Vth, gm, body factor, and drain-induced-barrier-lowering (DIBL) in individual transistors in SRAM cells are directly measured by 16k bit device-matrix-array (DMA) SRAM TEG. It is found that, besides Vth variability, DIBL variability degrades SRAM stability and its Vdd dependence while the variability of gm and body factor has only a small effect.
- 1 December 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 01631918,p. 3.5.1-3.5.4
Impact of DIBL variability on SRAM static noise margin analyzed by DMA SRAM TEG
The static noise margin (SNM) as well as Vth, gm, body factor, and drain-induced-barrier-lowering (DIBL) in individual transistors in SRAM cells are directly measured by 16k bit device-matrix-array (DMA) SRAM TEG. It is found that, besides Vth variability, DIBL variability degrades SRAM stability and its Vdd dependence while the variability of gm and body factor has only a small effect.