Triinu Poltimae
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Triinu Poltimae has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Heikko Kallakas
Laboratory of Wood Technology, Department of Materials and Environmental Technology, School of Engineering, Tallinn University of Technology, Ehitajate tee 5, 19086 Tallinn, Estonia
2 shared publications A Just
Department of Civil Engineering and Architecture, Tallinn University of Technology, Ehitajate tee 5, 19086 Tallinn, Estonia
1 shared publicationAivo Närep
1 shared publication- Andrey Aniskevich
Institute for Mechanics of Materials, University of Latvia, LV-1004 Riga, Latvia
1 shared publication J Kers
Department of Material and Environmental Technology: Laboratory of Wood Technology, Tallinn University of Technology, Ehitajate tee 5, 19086 Tallinn, Estonia
1 shared publicationJ Liblik
Department of Civil Engineering and Architecture, Tallinn University of Technology, Ehitajate tee 5, 19086 Tallinn, Estonia
1 shared publication
Latest Publications
- Open Access
- 1 June 2019
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 290 (1) , 012019
Fire and Mechanical Properties of Hemp and Clay Boards for Timber Structures
The use of timber with other bio-based building materials is often restricted due to the fire hazard. The primary protection for timber against fire is provided by cladding. Currently, there is limited fire protection design data on clay and hemp boards since they are relatively new products. Furthermore, the mechanical performance of boards is of utmost importance in timber frame assemblies. This paper presents a test program that determines the tensile and bending strength of boards accompanied by a comparison to widely used gypsum plasterboards. The fire protection effect for timber is assessed by using a cone heater. Main results indicate that clay and hemp boards are adequate alternatives for the gypsum plasterboards as they can demonstrate similar performance. Hemp boards made by dry method perform significantly better compared to the ones made by wet method. Clay boards with special additive demonstrate increased fire performance compared to more ecological boards. This study contributes to further research that is needed in order to provide design parameters for sustainable building solutions in the future.
- 1 June 2019
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 290 (1) , 012019
Open AccessFire and Mechanical Properties of Hemp and Clay Boards for Timber Structures
The use of timber with other bio-based building materials is often restricted due to the fire hazard. The primary protection for timber against fire is provided by cladding. Currently, there is limited fire protection design data on clay and hemp boards since they are relatively new products. Furthermore, the mechanical performance of boards is of utmost importance in timber frame assemblies. This paper presents a test program that determines the tensile and bending strength of boards accompanied by a comparison to widely used gypsum plasterboards. The fire protection effect for timber is assessed by using a cone heater. Main results indicate that clay and hemp boards are adequate alternatives for the gypsum plasterboards as they can demonstrate similar performance. Hemp boards made by dry method perform significantly better compared to the ones made by wet method. Clay boards with special additive demonstrate increased fire performance compared to more ecological boards. This study contributes to further research that is needed in order to provide design parameters for sustainable building solutions in the future.
- Open Access
- 26 April 2018
- Published by Estonian Academy Publishers in Proceedings of the Estonian Academy of Sciences
- Vol. 67 (2) , 183-192
Mechanical and physical properties of industrial hemp-based insulation materials; pp. 183–192
In recent years, research in the field of insulation materials in buildings has been focusing increasingly more upon ecological properties of these materials. Hemp is an annual bast fibre plant, which delivers fibres, shives, and seeds. Bast fibres are used as a raw material for thermal insulations while shives have been mainly used in animal bedding and construction. The aim of this research was to evaluate the mechanical and physical properties of the industrial hemp fibre- and bast-based insulation materials and compare them with wood-based materials. For producing hemp fibreboards, the hemp shives were ground with separative milling by a semi-industrial disintegrator to the average particle size of 0.136 mm. Urea–formaldehyde (UF) resin was used as the adhesive for hemp particleboards and fibreboards made by the dry method. Fibreboards made by the wet method were bonded without using any binders. Some fibreboards made by the dry method were covered with kraft paper on both sides using UF resin and PVA glue. Properties of particleboards and fibreboards were tested with the determination of density, swelling, resistance to axial withdrawal of screws, tensile strength perpendicular to the plane of the board, bending strength, and air permeability. The results showed that fibreboards made by the dry method were stronger and tougher than fibreboards made by the wet method. The only shortcoming of the former was their low water resistance as samples dissolved in water. Hemp particleboards were lighter and less dense than wood particleboards. However, the mechanical properties of the hemp particleboards were inferior to those of wood particleboards. In addition, the levels of water absorption and swelling of the hemp particleboards were higher than those of the wood particleboards.
- 26 April 2018
- Published by Estonian Academy Publishers in Proceedings of the Estonian Academy of Sciences
- Vol. 67 (2) , 183-192
Open AccessMechanical and physical properties of industrial hemp-based insulation materials; pp. 183–192
In recent years, research in the field of insulation materials in buildings has been focusing increasingly more upon ecological properties of these materials. Hemp is an annual bast fibre plant, which delivers fibres, shives, and seeds. Bast fibres are used as a raw material for thermal insulations while shives have been mainly used in animal bedding and construction. The aim of this research was to evaluate the mechanical and physical properties of the industrial hemp fibre- and bast-based insulation materials and compare them with wood-based materials. For producing hemp fibreboards, the hemp shives were ground with separative milling by a semi-industrial disintegrator to the average particle size of 0.136 mm. Urea–formaldehyde (UF) resin was used as the adhesive for hemp particleboards and fibreboards made by the dry method. Fibreboards made by the wet method were bonded without using any binders. Some fibreboards made by the dry method were covered with kraft paper on both sides using UF resin and PVA glue. Properties of particleboards and fibreboards were tested with the determination of density, swelling, resistance to axial withdrawal of screws, tensile strength perpendicular to the plane of the board, bending strength, and air permeability. The results showed that fibreboards made by the dry method were stronger and tougher than fibreboards made by the wet method. The only shortcoming of the former was their low water resistance as samples dissolved in water. Hemp particleboards were lighter and less dense than wood particleboards. However, the mechanical properties of the hemp particleboards were inferior to those of wood particleboards. In addition, the levels of water absorption and swelling of the hemp particleboards were higher than those of the wood particleboards.
- 13 November 2016
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 51 (21) , 2979-2988
Effective electrical conductivity of carbon nanotube–epoxy nanocomposites
The electrical conductivity of carbon nanotube–epoxy composites is investigated analytically and experimentally. The theoretical predictions of the effective electrical conductivity of carbon nanotube–epoxy composites were performed by the analytical approach based on a micromechanical model of composites. The parametric analysis carried out revealed an influence of geometrical and electrical parameters of the micromechanical model on the effective electrical conductivity of carbon nanotube–epoxy nanocomposite. The nanocomposites made from the DGEBA-based and RTM6 epoxy resins filled with different weight content of Baytubes C150P and N7000 multi-walled carbon nanotubes were prepared. The experimental values of the electrical conductivity of the nanocomposites were compared with those calculated by means of the analytical model.
- 13 November 2016
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 51 (21) , 2979-2988
Effective electrical conductivity of carbon nanotube–epoxy nanocomposites
The electrical conductivity of carbon nanotube–epoxy composites is investigated analytically and experimentally. The theoretical predictions of the effective electrical conductivity of carbon nanotube–epoxy composites were performed by the analytical approach based on a micromechanical model of composites. The parametric analysis carried out revealed an influence of geometrical and electrical parameters of the micromechanical model on the effective electrical conductivity of carbon nanotube–epoxy nanocomposite. The nanocomposites made from the DGEBA-based and RTM6 epoxy resins filled with different weight content of Baytubes C150P and N7000 multi-walled carbon nanotubes were prepared. The experimental values of the electrical conductivity of the nanocomposites were compared with those calculated by means of the analytical model.