Bader H. Albusairi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Bader H. Albusairi has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
Adam Al-Mulla
Kuwait University
2 shared publicationsJames T. Hsu
2 shared publicationsSami H. Ali
Department of Chemical Engineering, College of Engineering & Petroleum Kuwait University Kuwait City Kuwait
2 shared publicationsAbdulwahab S. Almusallam
Department of Chemical Engineering, College of Engineering & Petroleum Kuwait University Kuwait City Kuwait
1 shared publicationAli Y. Bumajdad
Department of Chemistry, College of Science Kuwait University Kuwait City Kuwait
1 shared publicationDina M. Hamad
1 shared publication
Latest Publications
- Open Access
- 21 March 2026
- Published by Elsevier in Chemical Engineering Journal Advances
- Vol. 26
Cofactor dynamics and diffusional limitations in packed bed flow bioreactors with multi-immobilized enzymes: Ketoreductase and glucose dehydrogenase
- 21 March 2026
- Published by Elsevier in Chemical Engineering Journal Advances
- Vol. 26
Open AccessCofactor dynamics and diffusional limitations in packed bed flow bioreactors with multi-immobilized enzymes: Ketoreductase and glucose dehydrogenase
- 6 February 2024
- Published by Wiley in The Canadian Journal of Chemical Engineering
- Vol. 102 (7) , 2511-2526
Production of esters with numerous applications: Kinetics of Dowex 50W catalyzed transesterification of methyl acetate with three‐ and four‐carbon structured alcohols
In this investigation, a strongly acidic exchange resin was used for the transesterification of methyl acetate with n‐propanol, n‐butanol, and iso‐butanol. Kinetic and equilibrium experiments for the three systems were conducted using a temperature‐controlled batch reactor setup. The effects of the following operating parameters on the transesterification were explored: reaction temperature, catalyst loading, and methyl acetate‐to‐alcohol molar ratio. The conversion of the limiting reactant in the reaction mixture increased with increasing reaction temperature, catalyst loading, and varying reactant proportions from 1:1 to other ratios. It was found that excess methyl acetate would result in higher limiting reactant conversion than using excess alcohol with the same initial molar proportionality between the excess and the limiting reactants. It was found that an increase in the chain length of the alcohol and/or branching suppressed the conversion of the reactants owing to steric hindrance. To mathematically correlate the data, several kinetic models were tested, and the Eley–Rideal model was selected. Accordingly, a reaction mechanism was proposed.
- 6 February 2024
- Published by Wiley in The Canadian Journal of Chemical Engineering
- Vol. 102 (7) , 2511-2526
Production of esters with numerous applications: Kinetics of Dowex 50W catalyzed transesterification of methyl acetate with three‐ and four‐carbon structured alcohols
In this investigation, a strongly acidic exchange resin was used for the transesterification of methyl acetate with n‐propanol, n‐butanol, and iso‐butanol. Kinetic and equilibrium experiments for the three systems were conducted using a temperature‐controlled batch reactor setup. The effects of the following operating parameters on the transesterification were explored: reaction temperature, catalyst loading, and methyl acetate‐to‐alcohol molar ratio. The conversion of the limiting reactant in the reaction mixture increased with increasing reaction temperature, catalyst loading, and varying reactant proportions from 1:1 to other ratios. It was found that excess methyl acetate would result in higher limiting reactant conversion than using excess alcohol with the same initial molar proportionality between the excess and the limiting reactants. It was found that an increase in the chain length of the alcohol and/or branching suppressed the conversion of the reactants owing to steric hindrance. To mathematically correlate the data, several kinetic models were tested, and the Eley–Rideal model was selected. Accordingly, a reaction mechanism was proposed.
- Open Access
- 1 February 2017
- Vol. 7 (1) , 79-90
A Study of Flow Properties of Kuwaiti Crude Oil Obtained from Different Sources
- 1 February 2017
- Vol. 7 (1) , 79-90
Open AccessA Study of Flow Properties of Kuwaiti Crude Oil Obtained from Different Sources
- 28 July 2016
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 51 (1) , 95-108
Development and characterization of novel polybutylene nanocomposites
Polybutylene/starch/nanoclay composite blends were prepared by melt extrusion technique. Maleic anhydride grafted polybutylene was used as a compatibilizer. The nanocomposites were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, atomic force microscopy, rheological, and mechanical analysis. Addition of compatibilizer to the polybutylene/starch/nanoclay showed dispersion and nucleation related to the nanoclay in the polybutylene matrix. An increase in the mechanical properties like modulus and tensile strength at break and a decrease in the elongation at break were observed on the addition of compatibilizer to the matrix compared to that of uncompatibilized matrix. The biodegradability of the nanocomposites was studied using the landfill burial test. The blends subjected to the burial test were evaluated for their tensile properties. The results revealed that the tensile strength and elongation at break of the compatibilized nanocomposites decreased after 80 days of land burial test compared to the initial period.
- 28 July 2016
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 51 (1) , 95-108
Development and characterization of novel polybutylene nanocomposites
Polybutylene/starch/nanoclay composite blends were prepared by melt extrusion technique. Maleic anhydride grafted polybutylene was used as a compatibilizer. The nanocomposites were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, atomic force microscopy, rheological, and mechanical analysis. Addition of compatibilizer to the polybutylene/starch/nanoclay showed dispersion and nucleation related to the nanoclay in the polybutylene matrix. An increase in the mechanical properties like modulus and tensile strength at break and a decrease in the elongation at break were observed on the addition of compatibilizer to the matrix compared to that of uncompatibilized matrix. The biodegradability of the nanocomposites was studied using the landfill burial test. The blends subjected to the burial test were evaluated for their tensile properties. The results revealed that the tensile strength and elongation at break of the compatibilized nanocomposites decreased after 80 days of land burial test compared to the initial period.
- 3 November 2009
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 23 (12) , 5986-5994
Removal of Dibenzothiophenes from Fuels by Oxy-desulfurization
- 3 November 2009
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 23 (12) , 5986-5994
Removal of Dibenzothiophenes from Fuels by Oxy-desulfurization
- 1 June 2007
- Published by Taylor & Francis in Separation Science and Technology
- Vol. 42 (9) , 2081-2097
Non‐Isothermal Non‐Adiabatic Dehydrogenation of Cyclohexane in Catalytic Membrane Reactors
This study focuses on modeling and analysis of the non‐isothermal, non‐adiabatic, dehydrogenation of cyclohexane in membrane catalytic reactors. The dehydrogenation reaction is endothermic with a low equilibrium conversion of 0.06 at a temperature of 473 K and pressure of 101 kPa. The membrane reactor removes hydrogen from the reaction mixture and results in increase of the reaction conversion. The analysis is made as a function of feed flow rate, feed temperature, feed composition, inert flow rate in the feed stream, flow rate of sweep gas, pressures of the tube side and shell side, permeability constant of hydrogen, and tube diameter. The analysis also includes a study of the co‐current and the counter‐current flow modes. The results show lower conversion for the counter‐current flow mode, because of the decrease in the driving force for permeation. A comparison of model predictions against previous literature studies shows good agreement.
- 1 June 2007
- Published by Taylor & Francis in Separation Science and Technology
- Vol. 42 (9) , 2081-2097
Non‐Isothermal Non‐Adiabatic Dehydrogenation of Cyclohexane in Catalytic Membrane Reactors
This study focuses on modeling and analysis of the non‐isothermal, non‐adiabatic, dehydrogenation of cyclohexane in membrane catalytic reactors. The dehydrogenation reaction is endothermic with a low equilibrium conversion of 0.06 at a temperature of 473 K and pressure of 101 kPa. The membrane reactor removes hydrogen from the reaction mixture and results in increase of the reaction conversion. The analysis is made as a function of feed flow rate, feed temperature, feed composition, inert flow rate in the feed stream, flow rate of sweep gas, pressures of the tube side and shell side, permeability constant of hydrogen, and tube diameter. The analysis also includes a study of the co‐current and the counter‐current flow modes. The results show lower conversion for the counter‐current flow mode, because of the decrease in the driving force for permeation. A comparison of model predictions against previous literature studies shows good agreement.
- 30 March 2005
- Published by Wiley in AIChE Journal
- Vol. 51 (5) , 1330-1338
Dispersion coefficient prediction within a bed packed with perfusive particles
The effective medium model of perfusive particles has been used to modify the dispersion coefficient of a packed bed to account for intraparticle velocity and internal structure of the perfusive particles. In this model, the diffusivity factor has been derived by solving the steady‐state diffusion equation in the three regions (that is, external, envelope, and internal regions) of the effective medium model and proved experimentally. The diffusivity factor is incorporated with hydrodynamic parameters obtained earlier to modify the dispersion coefficient of bed packed with perfusive particles. It was found that the diffusivity factor is independent of perfusive particle shape. Also, it was found that the uniformity of perfusive particles is not a necessary condition, once average accessible porosity is considered instead of actual porosity. Finally, it was shown that a significant error would be introduced to predict the performance of bed packed with perfusive particles if the effect of perfusive phenomena on the dispersion coefficient of a packed bed were not considered. © 2005 American Institute of Chemical Engineers AIChE J, 2005
- 30 March 2005
- Published by Wiley in AIChE Journal
- Vol. 51 (5) , 1330-1338
Dispersion coefficient prediction within a bed packed with perfusive particles
The effective medium model of perfusive particles has been used to modify the dispersion coefficient of a packed bed to account for intraparticle velocity and internal structure of the perfusive particles. In this model, the diffusivity factor has been derived by solving the steady‐state diffusion equation in the three regions (that is, external, envelope, and internal regions) of the effective medium model and proved experimentally. The diffusivity factor is incorporated with hydrodynamic parameters obtained earlier to modify the dispersion coefficient of bed packed with perfusive particles. It was found that the diffusivity factor is independent of perfusive particle shape. Also, it was found that the uniformity of perfusive particles is not a necessary condition, once average accessible porosity is considered instead of actual porosity. Finally, it was shown that a significant error would be introduced to predict the performance of bed packed with perfusive particles if the effect of perfusive phenomena on the dispersion coefficient of a packed bed were not considered. © 2005 American Institute of Chemical Engineers AIChE J, 2005
- 1 July 2004
- Published by Elsevier in Chemical Engineering Journal
- Vol. 100 (1-3) , 79-84
Flow through beds of perfusive particles: effective medium model for velocity prediction within the perfusive media
- 1 July 2004
- Published by Elsevier in Chemical Engineering Journal
- Vol. 100 (1-3) , 79-84
Flow through beds of perfusive particles: effective medium model for velocity prediction within the perfusive media
- 1 October 2002
- Published by Elsevier in Chemical Engineering Journal
- Vol. 89 (1-3) , 173-183
Application of shape factor to determine the permeability of perfusive particles
- 1 October 2002
- Published by Elsevier in Chemical Engineering Journal
- Vol. 89 (1-3) , 173-183
Application of shape factor to determine the permeability of perfusive particles