Masahide Kuwata
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Masahide Kuwata has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Keisuke Asai
Tohoku University
2 shared publications - Shigeru Obayashi
Institute of Fluid Science, Tohoku University, Sendai, Japan
2 shared publications - Sho Yokota
Department of Aerospace Engineering, Graduate School of Engineering, Tohoku University , Sendai, Miyagi 980-8579, Japan
2 shared publications - Taku Nonomura
Tohoku University
2 shared publications - Yoshiaki Abe
Tohoku University
2 shared publications - Aiko Yakeno
Tohoku University
1 shared publication
Latest Publications
- 1 February 2023
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 94 (2) , 025102
Model position sensing method for low fineness ratio models in a magnetic suspension and balance system
A new model-position-sensing method for the levitation of models with a low fineness ratio (ratio of the longitudinal length to the diameter) in a magnetic suspension and balance system (MSBS) is proposed. MSBS is an ideal model-support device for wind-tunnel testing, which enables the study of flow fields around blunt bodies without flow disturbances introduced by mechanical support devices, with the aerodynamic forces determined from the magnetic forces using a pre-calibrated relationship. The new method allows wind tunnel experiments without mechanical supports with a low fineness ratio model. This method adopts two line sensors placed parallel to the central axis of the model image and measures the position with a resolution finer than 0.06 mm or deg even for thin model geometries. In addition, measurement errors were reduced by correcting a second-order term in the depth direction of the camera. A low fineness ratio circular cylinder model was levitated following sensor calibration. The model was supported in conditions with and without freestream flow. This position measurement method was also applied to a reentry capsule model. The model was levitated while keeping its position and attitude stabilized near the origin.
- 1 February 2023
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 94 (2) , 025102
Model position sensing method for low fineness ratio models in a magnetic suspension and balance system
A new model-position-sensing method for the levitation of models with a low fineness ratio (ratio of the longitudinal length to the diameter) in a magnetic suspension and balance system (MSBS) is proposed. MSBS is an ideal model-support device for wind-tunnel testing, which enables the study of flow fields around blunt bodies without flow disturbances introduced by mechanical support devices, with the aerodynamic forces determined from the magnetic forces using a pre-calibrated relationship. The new method allows wind tunnel experiments without mechanical supports with a low fineness ratio model. This method adopts two line sensors placed parallel to the central axis of the model image and measures the position with a resolution finer than 0.06 mm or deg even for thin model geometries. In addition, measurement errors were reduced by correcting a second-order term in the depth direction of the camera. A low fineness ratio circular cylinder model was levitated following sensor calibration. The model was supported in conditions with and without freestream flow. This position measurement method was also applied to a reentry capsule model. The model was levitated while keeping its position and attitude stabilized near the origin.
- 27 May 2021
- Published by American Physical Society (APS) in Physical Review Fluids
- Vol. 6 (5) , 054704
Flow characteristics around extremely low fineness-ratio circular cylinders
The accurate measurement of flows and aerodynamic characteristics around a bluff body has been a challenging task due to the existence of interference between the wake and mechanical model supports in wind-tunnel experiments. The present study focuses on a freestream-aligned circular cylinder with an extremely low fineness ratio (the ratio of the axial length to diameter) ranging from 0.30 to 0.50, which has never been investigated without interference from a mechanical model support. We employed a magnetic suspension and balance system to eliminate interference from the model support and measured the drag and velocity fields in the diameter-based Reynolds number between and . As the fineness ratio decreases below 1.50, the size of the recirculation bubble increases and the velocity distribution on the central axis inside the bubble gradually converges to that of the circular disk. Furthermore, large-eddy simulations were performed in the Reynolds number of , whose drag coefficient agrees well with experiments. Based on those results, it was found that the drag coefficient monotonically converges to that of the circular disk without local maximum. This study revealed that in the low-fineness-ratio regime (0.10–0.50), a critical geometry, at which the drag coefficient shows a local maximum, does not exist in the circular cylinder. Subsequently, unsteady flow analyses were performed, where two characteristic frequencies, i.e., and 0.155, were identified from power spectral densities of the drag coefficient and the pitching moment coefficient. The associated flow structures are then extracted by a phase-averaging procedure, where the phase-averaged flows with represent the recirculation bubble pumping while the phase-averaged flows with show nonaxisymmetric structures inside the recirculation bubble.- 27 May 2021
- Published by American Physical Society (APS) in Physical Review Fluids
- Vol. 6 (5) , 054704
Flow characteristics around extremely low fineness-ratio circular cylinders
The accurate measurement of flows and aerodynamic characteristics around a bluff body has been a challenging task due to the existence of interference between the wake and mechanical model supports in wind-tunnel experiments. The present study focuses on a freestream-aligned circular cylinder with an extremely low fineness ratio (the ratio of the axial length to diameter) ranging from 0.30 to 0.50, which has never been investigated without interference from a mechanical model support. We employed a magnetic suspension and balance system to eliminate interference from the model support and measured the drag and velocity fields in the diameter-based Reynolds number between and . As the fineness ratio decreases below 1.50, the size of the recirculation bubble increases and the velocity distribution on the central axis inside the bubble gradually converges to that of the circular disk. Furthermore, large-eddy simulations were performed in the Reynolds number of , whose drag coefficient agrees well with experiments. Based on those results, it was found that the drag coefficient monotonically converges to that of the circular disk without local maximum. This study revealed that in the low-fineness-ratio regime (0.10–0.50), a critical geometry, at which the drag coefficient shows a local maximum, does not exist in the circular cylinder. Subsequently, unsteady flow analyses were performed, where two characteristic frequencies, i.e., and 0.155, were identified from power spectral densities of the drag coefficient and the pitching moment coefficient. The associated flow structures are then extracted by a phase-averaging procedure, where the phase-averaged flows with represent the recirculation bubble pumping while the phase-averaged flows with show nonaxisymmetric structures inside the recirculation bubble.