Gabriela S. Diogo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Gabriela S. Diogo has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Ilídio Joaquim Correia
RISE-Health, Departamento de Ciências Médicas, Faculdade de Ciências da Saúde, Universidade da Beira Interior, Av. Infante D. Henrique, 6200-506 Covilhã, Portugal; AEROG-LAETA, Aerospace Sciences Department, Universidade da Beira Interior, Covilhã, Portugal; University of Coimbra, CERES - Centro de Engenharia Química e Recursos Renováveis para a Sustentabilidade, Department of Chemical Engineering, Coimbra 3030-790, Portugal
2 shared publications - Ricardo Fradique
Department of Physics, Cavendish Laboratory, University of Cambridge, Cambridge, UK
2 shared publications - Rui Luis Reis
University of Minho, Headquarters of the European Institute of Excellence on Tissue Engineering and Regenerative Medicine
2 shared publications - Tiago Henriques Silva
B's Research Group, I3B's - Research Institute on Biomaterials, Biodegradables and Biomimetics of University of Minho, Headquarters of the European Institute of Excellence on Tissue Engineering and Regenerative Medicine, AvePark 4805-017, Barco, Guimarães, Portugal; ICVS/3B's - PT, Government Associate Laboratory, Braga, Guimarães, Portugal
2 shared publications - Vitor M. Gaspar
Department of Chemistry CICECO – Aveiro Institute of Materials University of Aveiro Campus Universitário de Santiago Aveiro 3810‐193 Portugal
2 shared publications - Abilio Pereira Silva
UBI - University of Beira Interior
1 shared publication
Latest Publications
- 1 September 2017
- Published by Elsevier in Materials Science and Engineering: C
- Vol. 78, 787-795
Extraction and characterization of collagen from Antarctic and Sub-Antarctic squid and its potential application in hybrid scaffolds for tissue engineering
- 1 September 2017
- Published by Elsevier in Materials Science and Engineering: C
- Vol. 78, 787-795
Extraction and characterization of collagen from Antarctic and Sub-Antarctic squid and its potential application in hybrid scaffolds for tissue engineering
- 14 October 2016
- Published by Wiley
- p. 16-36
Marine Collagen Isolation and Processing Envisaging Biomedical Applications
- 14 October 2016
- Published by Wiley
- p. 16-36
Marine Collagen Isolation and Processing Envisaging Biomedical Applications
- 21 March 2014
- Published by IOP Publishing in Biofabrication
- Vol. 6 (2) , 025001
Manufacture of β-TCP/alginate scaffolds through a Fab@home model for application in bone tissue engineering
The growing need to treat bone-related diseases in an elderly population compels the development of novel bone substitutes to improve patient quality of life. In this context, the advent of affordable and effective rapid prototyping equipment, such as the Fab@home plotter, has contributed to the development of novel scaffolds for bone tissue engineering. In this study, we report for the first time the use of a Fab@home plotter for the production of 3D scaffolds composed by beta-tricalcium phosphate (β-TCP)/alginate hybrid materials. β-TCP/alginate mixtures were used in a proportion of 50/50% (w/w), 30/70% (w/w) and 20/80% (w/w). The printing parameters were optimized to a nozzle diameter of 20 Gauge for the production of rigid scaffolds with pre-defined architectures. We observed that, despite using similar printing parameters, both the precision and resolution of the scaffolds were significantly affected by the blend's viscosity. In particular, we demonstrate that the higher viscosity of 50/50 scaffolds (150.0 ± 3.91 mPa s) provides a higher precision in the extrusion process. The physicochemical and biological characterization of the samples demonstrated that the 50/50 scaffolds possessed a resistance to compression comparable to that of native trabecular bone. Moreover, this particular formulation also exhibited a Young's modulus that was higher than that of trabecular bone. Scanning electron microscopy and fluorescence microscopy analysis revealed that osteoblasts were able to adhere, proliferate and also penetrate into the scaffold's architecture. Altogether, our findings suggest that the Fab@home printer can be employed in the manufacture of reproducible scaffolds, using a formulation 50/50 alginate-β-TCP that has suitable properties to be applied as bone substitutes in the future.
- 21 March 2014
- Published by IOP Publishing in Biofabrication
- Vol. 6 (2) , 025001
Manufacture of β-TCP/alginate scaffolds through a Fab@home model for application in bone tissue engineering
The growing need to treat bone-related diseases in an elderly population compels the development of novel bone substitutes to improve patient quality of life. In this context, the advent of affordable and effective rapid prototyping equipment, such as the Fab@home plotter, has contributed to the development of novel scaffolds for bone tissue engineering. In this study, we report for the first time the use of a Fab@home plotter for the production of 3D scaffolds composed by beta-tricalcium phosphate (β-TCP)/alginate hybrid materials. β-TCP/alginate mixtures were used in a proportion of 50/50% (w/w), 30/70% (w/w) and 20/80% (w/w). The printing parameters were optimized to a nozzle diameter of 20 Gauge for the production of rigid scaffolds with pre-defined architectures. We observed that, despite using similar printing parameters, both the precision and resolution of the scaffolds were significantly affected by the blend's viscosity. In particular, we demonstrate that the higher viscosity of 50/50 scaffolds (150.0 ± 3.91 mPa s) provides a higher precision in the extrusion process. The physicochemical and biological characterization of the samples demonstrated that the 50/50 scaffolds possessed a resistance to compression comparable to that of native trabecular bone. Moreover, this particular formulation also exhibited a Young's modulus that was higher than that of trabecular bone. Scanning electron microscopy and fluorescence microscopy analysis revealed that osteoblasts were able to adhere, proliferate and also penetrate into the scaffold's architecture. Altogether, our findings suggest that the Fab@home printer can be employed in the manufacture of reproducible scaffolds, using a formulation 50/50 alginate-β-TCP that has suitable properties to be applied as bone substitutes in the future.
- 1 October 2013
- Published by Elsevier in Materials Science and Engineering: C
- Vol. 33 (7) , 4460-4469
Bioactive polymeric–ceramic hybrid 3D scaffold for application in bone tissue regeneration
- 1 October 2013
- Published by Elsevier in Materials Science and Engineering: C
- Vol. 33 (7) , 4460-4469
Bioactive polymeric–ceramic hybrid 3D scaffold for application in bone tissue regeneration