Jochen Busam
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jochen Busam has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Marisa Di Sabatino
Norwegian University of Science and Technology
2 shared publications Astrid Marie F. Muggerud
The Quartz Corp Drag Norway
1 shared publicationAstrid Marthinsen
SINTEF Industry, Forskningsveien 1, 0373 Oslo, Norway
1 shared publication- Bartłomiej Adam Gaweł
The Quartz Corp, Hellandsveien 14, 8270 Drag, Norway
1 shared publication Benny Hallam
The Quartz Corp, Hellandsveien 14, 8270 Drag, Norway
1 shared publicationGabriela Kazimiera Warden
Department of Materials Science and Engineering, Norwegian University of Science and Technology (NTNU), S. Saelandsvei 12, 7491 Trondheim, Norway
1 shared publication
Latest Publications
- Open Access
- 22 April 2024
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 14 (19) , 13669-13675
Influence of aluminium doping on high purity quartz glass properties
High purity natural quartz is used as raw material for the manufacture of quartz glass crucibles for solar-grade silicon ingots production. One key challenge for cost-effective ingot pulling is to maximise the ability of the crucible to withstand the process conditions (i.e., silicon load and temperature about 1500 °C) without deformation. In order to improve this glass property, aluminium was coated into the raw quartz materials. Our results showed that an addition of up to 1000 wt ppm Al substantially reduces deformation of glass and improves viscosity at high temperatures. This is likely due to the reduction of stability of OH groups in the quartz glass as well as a trapping effect of aluminium on oxygen vacancies. This hypothesis is also supported by atomistic models. In the presence of Al, formation energies of silanol groups (Si–O–H) were much higher than without. Furthermore, the presence of Al in the structure significantly reduces mobility of the oxygen vacancies. It was also found that formation of oxygen vacancies hinders cristobalite crystallisation, on the other hand, Al atoms themselves induce local weakening of the Si–O bond which accelerates the kinetics of the reconstructive phase transition from glassy state to crystalline phase. This was also confirmed experimentally in our study.
- 22 April 2024
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 14 (19) , 13669-13675
Open AccessInfluence of aluminium doping on high purity quartz glass properties
High purity natural quartz is used as raw material for the manufacture of quartz glass crucibles for solar-grade silicon ingots production. One key challenge for cost-effective ingot pulling is to maximise the ability of the crucible to withstand the process conditions (i.e., silicon load and temperature about 1500 °C) without deformation. In order to improve this glass property, aluminium was coated into the raw quartz materials. Our results showed that an addition of up to 1000 wt ppm Al substantially reduces deformation of glass and improves viscosity at high temperatures. This is likely due to the reduction of stability of OH groups in the quartz glass as well as a trapping effect of aluminium on oxygen vacancies. This hypothesis is also supported by atomistic models. In the presence of Al, formation energies of silanol groups (Si–O–H) were much higher than without. Furthermore, the presence of Al in the structure significantly reduces mobility of the oxygen vacancies. It was also found that formation of oxygen vacancies hinders cristobalite crystallisation, on the other hand, Al atoms themselves induce local weakening of the Si–O bond which accelerates the kinetics of the reconstructive phase transition from glassy state to crystalline phase. This was also confirmed experimentally in our study.
- 30 November 2021
- Published by Royal Society of Chemistry (RSC) in Journal of Analytical Atomic Spectrometry
- Vol. 37 (1) , 172-177
Silicon and indium as secondary cathodes for the analysis of solid alumina and sapphire by slow-flow direct-current glow discharge mass spectrometry
We demonstrate and compare the capabilities of indium and silicon as secondary cathodes for the analysis of flat, solid alumina and sapphire matrices by direct current glow discharge mass spectrometry (dc-GDMS).
- 30 November 2021
- Published by Royal Society of Chemistry (RSC) in Journal of Analytical Atomic Spectrometry
- Vol. 37 (1) , 172-177
Silicon and indium as secondary cathodes for the analysis of solid alumina and sapphire by slow-flow direct-current glow discharge mass spectrometry
We demonstrate and compare the capabilities of indium and silicon as secondary cathodes for the analysis of flat, solid alumina and sapphire matrices by direct current glow discharge mass spectrometry (dc-GDMS).
- Open Access
- 27 May 2021
- Published by Wiley in Journal of Mass Spectrometry
- Vol. 56 (8) , e4771
Application of 7N In as secondary cathode for the direct current‐glow discharge mass spectrometry analysis of solid, fused high‐purity quartz
Direct current glow discharge mass spectrometry with an indium‐based secondary cathode technique is used to analyze solid, nonconducting, fused high‐purity quartz regarding metallic impurities of relevance to the solar industry. Details of the analytical routines are presented. In this work, the secondary cathode design and glow discharge conditions are optimized beyond the commonly applied practices. In addition, relative sensitivity factors (RSFs) for these optimized conditions are established and compared to previously published results. The results indicate that the technique enables stable measurements with detection limits down to the part per billion (ppb) range.
- 27 May 2021
- Published by Wiley in Journal of Mass Spectrometry
- Vol. 56 (8) , e4771
Open AccessApplication of 7N In as secondary cathode for the direct current‐glow discharge mass spectrometry analysis of solid, fused high‐purity quartz
Direct current glow discharge mass spectrometry with an indium‐based secondary cathode technique is used to analyze solid, nonconducting, fused high‐purity quartz regarding metallic impurities of relevance to the solar industry. Details of the analytical routines are presented. In this work, the secondary cathode design and glow discharge conditions are optimized beyond the commonly applied practices. In addition, relative sensitivity factors (RSFs) for these optimized conditions are established and compared to previously published results. The results indicate that the technique enables stable measurements with detection limits down to the part per billion (ppb) range.