Petros Sideris
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Petros Sideris has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Arnaud Peizerat
Commissariat à l’Energie Atomique et aux Energies Alternatives—Laboratoire d′Electronique des Technologies de l′Information (CEA—LETI), University Grenoble Alpes, 38054 Grenoble, France
1 shared publication - C. Fenouillet-Beranger
CEA-LETI, Grenoble, France
1 shared publication C. Theodorou
CEA, LETI, Université Grenoble Alpes, Grenoble, France
1 shared publication- Christoforos Theodorou
French National Centre for Scientific Research (CNRS), Centre for Radiofrequencies, Optic and Micro-nanoelectronics (CROMA), University of Grenoble Alpes, University of Savoie Mont-Blanc Grenoble INP, 38000 Grenoble, France
1 shared publication F. Gaillard
CEA, LETI, Université Grenoble Alpes, Grenoble, France
1 shared publication- Gilles Sicard
CEA-LETI, Université Grenoble Alpes, F-38000, 17 Avenue des Martyrs, Grenoble, 38054, France
1 shared publication
Latest Publications
- Open Access
- 28 February 2022
- Published by MDPI AG in Technologies
- Vol. 10 (2) , 38
Parasitic Coupling in 3D Sequential Integration: The Example of a Two-Layer 3D Pixel
In this paper, we present a thorough analysis of parasitic coupling effects between different electrodes for a 3D Sequential Integration circuit example comprising stacked devices. More specifically, this study is performed for a Back-Side Illuminated, 4T–APS, 3D Sequential Integration pixel with both its photodiode and Transfer Gate at the bottom tier and the other parts of the circuit on the top tier. The effects of voltage bias and 3D inter-tier contacts are studied by using TCAD simulations. Coupling-induced electrical parameter variations are compared against variations due to temperature change, revealing that these two effects can cause similar levels of readout error for the top-tier readout circuit. On the bright side, we also demonstrate that in the case of a rolling shutter pixel readout, the coupling effect becomes nearly negligible. Therefore, we estimate that the presence of an inter-tier ground plane, normally used for electrical isolation, is not strictly mandatory for Monolithic 3D pixels.
- 28 February 2022
- Published by MDPI AG in Technologies
- Vol. 10 (2) , 38
Open AccessParasitic Coupling in 3D Sequential Integration: The Example of a Two-Layer 3D Pixel
In this paper, we present a thorough analysis of parasitic coupling effects between different electrodes for a 3D Sequential Integration circuit example comprising stacked devices. More specifically, this study is performed for a Back-Side Illuminated, 4T–APS, 3D Sequential Integration pixel with both its photodiode and Transfer Gate at the bottom tier and the other parts of the circuit on the top tier. The effects of voltage bias and 3D inter-tier contacts are studied by using TCAD simulations. Coupling-induced electrical parameter variations are compared against variations due to temperature change, revealing that these two effects can cause similar levels of readout error for the top-tier readout circuit. On the bright side, we also demonstrate that in the case of a rolling shutter pixel readout, the coupling effect becomes nearly negligible. Therefore, we estimate that the presence of an inter-tier ground plane, normally used for electrical isolation, is not strictly mandatory for Monolithic 3D pixels.
- 27 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 68 (7) , 3157-3162
RF Performance of Devices Processed in Low-Temperature Sequential Integration
RF performance and intertier coupling of CMOS processed in 3-D sequential integration are investigated. pMOS transistor fabricated with a 500 °C thermal budget features good RF figures of merit with ${f}_{t} =105$ GHz and ${f}_{\text {max}} =175$ GHz for a gate length of 45 nm and ${V}_{\text {DD}} = -1$ V. Moreover, we demonstrate that the low- ${k}$ SiCO oxide spacer and low polysilicon gate resistance obtained with the low temperature process contribute to ${f}_{\text {max}}$ results that are better than high temperature process (above 1000°). Finally, we illustrate the crosstalk effects and the influence of the low-tier transistor gate voltage ${V}_{\text {G}}$ on the top-tier threshold voltage ${V}_{T}$ . We also show that a polysilicon ground shield integrated under the top-tier transistor substantially attenuates the intertier RF field coupling effects.
- 27 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 68 (7) , 3157-3162
RF Performance of Devices Processed in Low-Temperature Sequential Integration
RF performance and intertier coupling of CMOS processed in 3-D sequential integration are investigated. pMOS transistor fabricated with a 500 °C thermal budget features good RF figures of merit with ${f}_{t} =105$ GHz and ${f}_{\text {max}} =175$ GHz for a gate length of 45 nm and ${V}_{\text {DD}} = -1$ V. Moreover, we demonstrate that the low- ${k}$ SiCO oxide spacer and low polysilicon gate resistance obtained with the low temperature process contribute to ${f}_{\text {max}}$ results that are better than high temperature process (above 1000°). Finally, we illustrate the crosstalk effects and the influence of the low-tier transistor gate voltage ${V}_{\text {G}}$ on the top-tier threshold voltage ${V}_{T}$ . We also show that a polysilicon ground shield integrated under the top-tier transistor substantially attenuates the intertier RF field coupling effects.