Thomas A. de Bruijn
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Thomas A. de Bruijn has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
F.W.J. van Hattum
1 shared publication- G. Vincent
Department of Mechanical Engineering, University of Twente, P.O. box 770, 7500 AT Enschede, The Netherlands
1 shared publication G.A. Vincent
1 shared publicationGuillaume A. Vincent
1 shared publicationJ. Meuzelaar
1 shared publication- João Pedro Nunes
University of Minho
1 shared publication
Latest Publications
- Open Access
- 1 November 2019
- Published by Elsevier in Composites Part B: Engineering
- Vol. 176
Shredding and sieving thermoplastic composite scrap: Method development and analyses of the fibre length distributions
- 1 November 2019
- Published by Elsevier in Composites Part B: Engineering
- Vol. 176
Open AccessShredding and sieving thermoplastic composite scrap: Method development and analyses of the fibre length distributions
- 1 January 2017
- Published by AIP Publishing in AIP Conference Proceedings
Impregnation quality of shredded semipreg after compression moulding
Manufacturing of thermoplastic composites (TPC) inherently generates scrap, mainly in the form of offcuts or rejected parts. The growth of TPC over recent decades has now reached a point where developing specific recycling solutions for TPC waste has become crucial. While looking at the various steps during which scrap is produced, the nesting of semipreg or prepreg appears to be critical. This work aims to develop a route for recycling semipreg offcuts, comprising shredding and compression moulding. This article focuses on an experimental study of the compression moulding step of carbon fibres reinforced PPS (C/PPS) to investigate the uniformity and impregnation quality of plates. These plates were realised in a picture frame while varying both the fibre volume content between 30% and 50% and the processing parameters. Visual inspection and cross-sectional microscopy were performed to assess the quality of each plate. As a first step, the influence of the type of added matrix (film, powder, pellets) and the type of pre-impregnation (film, powder) was studied. Stacking of polymer powder with shredded powder-coated semipreg gave the best impregnation quality. It was also shown that longer dwell time at melt leads to better consolidation quality. However, the difficulty in obtaining good impregnation comes from the disentangled shredded material, which is composed of three forms: semipreg flakes, dry bundles and pieces of matrix. When dry bundles reach the mould surfaces during the filling of the mould or when they are packed together, the consolidation cycle hardly impregnates them and they remain dry afterwards. Furthermore, large local variations of fibre fraction were noticed, resulting from a random mould filling. Therefore, the recycling solution for shredded semipreg is feasible when the fibre fraction is reduced but improvements on the part variability still have to be made.
- 1 January 2017
- Published by AIP Publishing in AIP Conference Proceedings
Impregnation quality of shredded semipreg after compression moulding
Manufacturing of thermoplastic composites (TPC) inherently generates scrap, mainly in the form of offcuts or rejected parts. The growth of TPC over recent decades has now reached a point where developing specific recycling solutions for TPC waste has become crucial. While looking at the various steps during which scrap is produced, the nesting of semipreg or prepreg appears to be critical. This work aims to develop a route for recycling semipreg offcuts, comprising shredding and compression moulding. This article focuses on an experimental study of the compression moulding step of carbon fibres reinforced PPS (C/PPS) to investigate the uniformity and impregnation quality of plates. These plates were realised in a picture frame while varying both the fibre volume content between 30% and 50% and the processing parameters. Visual inspection and cross-sectional microscopy were performed to assess the quality of each plate. As a first step, the influence of the type of added matrix (film, powder, pellets) and the type of pre-impregnation (film, powder) was studied. Stacking of polymer powder with shredded powder-coated semipreg gave the best impregnation quality. It was also shown that longer dwell time at melt leads to better consolidation quality. However, the difficulty in obtaining good impregnation comes from the disentangled shredded material, which is composed of three forms: semipreg flakes, dry bundles and pieces of matrix. When dry bundles reach the mould surfaces during the filling of the mould or when they are packed together, the consolidation cycle hardly impregnates them and they remain dry afterwards. Furthermore, large local variations of fibre fraction were noticed, resulting from a random mould filling. Therefore, the recycling solution for shredded semipreg is feasible when the fibre fraction is reduced but improvements on the part variability still have to be made.