Aiping Song
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Aiping Song has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Jianzhou Pan
School of Mechanical Engineering, Yangzhou University, Yangzhou 225127, China
2 shared publications - Bing Zhang
College of Mechanical Engineering, Institute of Technology for Carbon Neutralization, Yangzhou University, Yangzhou, China
1 shared publication - Chenwei Yu
School of Mechanical Engineering, Yangzhou University, Yangzhou 225127, China
1 shared publication - Chuang Yan
School of Mechanical Engineering, Yangzhou University, Yangzhou 225127, China
1 shared publication - Jiaming Huang
School of Mechanical Engineering, Yangzhou University, Yangzhou 225127, China
1 shared publication - M. Shafin. H. Qureshi
College of Mechanical Engineering, Yangzhou University, Yangzhou 225127, China
1 shared publication
Latest Publications
- Open Access
In-Situ Assembly of MoS2 Nanostructures on EHD-Printed Microscale PVDF Fibrous Films for Potential Energy Storage Applications
Three-dimensional (3D) printing has been widely utilized to fabricate free-standing electrodes in energy-related fields. In terms of fabrication, the two most challenging limitations of 3D printed electrodes are the poor printing resolution and simple structural dimension. Here we proposed a novel process to fabricate molybdenum disulfide-polyvinylidene fluoride (MoS2-PVDF) hierarchical electrodes for energy storage applications. The 20-layer microscale PVDF films with a stable fiber width of 8.3 ± 1.2 μm were fabricated by using electrohydrodynamic (EHD) printing. MoS2 nanostructures were synthesized and assembled on the microscale PVDF fibers by using hydrothermal crystal growth. The structural and material investigations were conducted to demonstrate the geometrical morphology and materials component of the composite structure. The electrochemical measurements indicated that the MoS2-PVDF electrodes exhibited the typical charge-discharge performance with a mass specific capacitance of 60.2 ± 4.5 F/g. The proposed method offers a facile and scalable approach for the fabrication of high-resolution electrodes, which might be further developed with enhanced specific capacitance in energy storage fields.
Open AccessIn-Situ Assembly of MoS2 Nanostructures on EHD-Printed Microscale PVDF Fibrous Films for Potential Energy Storage Applications
Three-dimensional (3D) printing has been widely utilized to fabricate free-standing electrodes in energy-related fields. In terms of fabrication, the two most challenging limitations of 3D printed electrodes are the poor printing resolution and simple structural dimension. Here we proposed a novel process to fabricate molybdenum disulfide-polyvinylidene fluoride (MoS2-PVDF) hierarchical electrodes for energy storage applications. The 20-layer microscale PVDF films with a stable fiber width of 8.3 ± 1.2 μm were fabricated by using electrohydrodynamic (EHD) printing. MoS2 nanostructures were synthesized and assembled on the microscale PVDF fibers by using hydrothermal crystal growth. The structural and material investigations were conducted to demonstrate the geometrical morphology and materials component of the composite structure. The electrochemical measurements indicated that the MoS2-PVDF electrodes exhibited the typical charge-discharge performance with a mass specific capacitance of 60.2 ± 4.5 F/g. The proposed method offers a facile and scalable approach for the fabrication of high-resolution electrodes, which might be further developed with enhanced specific capacitance in energy storage fields.
- Open Access
Precise Measurement and Visual Expression of Gear Overall Deviation
This paper proposes a non-contact measurement, analysis, and visualization method for the overall deviation of gears based on a laser displacement sensor. We implement error compensation and coordinate transformation on the tooth profile data collected by the laser probe through an algorithm, and fit all the data points to the gear surface using a 3 × 3 degree spline function. According to the established actual surface model of the gear, the tooth profile curve on any section of the gear and its various deviations can be obtained. To find the overall deviation on the tooth profile surface, the deviation data is refined and fitted into a curved surface by the Newton difference method. The overall deviation can be represented on the gear surface in the form of a color map, and then the color map of the overall deviation of the gear can be obtained. In addition, it can intuitively analyze the distribution of the overall deviation on the gear surface, and realize the visual expression of the deviation. Finally, through experimental verification, we prove that this method can quickly and accurately analyze the various deviations of the gears and the distribution of the deviation, and can effectively improve the detection accuracy and efficiency of the gears.
Open AccessPrecise Measurement and Visual Expression of Gear Overall Deviation
This paper proposes a non-contact measurement, analysis, and visualization method for the overall deviation of gears based on a laser displacement sensor. We implement error compensation and coordinate transformation on the tooth profile data collected by the laser probe through an algorithm, and fit all the data points to the gear surface using a 3 × 3 degree spline function. According to the established actual surface model of the gear, the tooth profile curve on any section of the gear and its various deviations can be obtained. To find the overall deviation on the tooth profile surface, the deviation data is refined and fitted into a curved surface by the Newton difference method. The overall deviation can be represented on the gear surface in the form of a color map, and then the color map of the overall deviation of the gear can be obtained. In addition, it can intuitively analyze the distribution of the overall deviation on the gear surface, and realize the visual expression of the deviation. Finally, through experimental verification, we prove that this method can quickly and accurately analyze the various deviations of the gears and the distribution of the deviation, and can effectively improve the detection accuracy and efficiency of the gears.
- Open Access
An Offset Laser Measurement Method for the Deviation Analysis of Cylindrical Gears
Generally, in the laser measurement of gears, the laser beam passes through the center of the gear, and the laser displacement sensor reads the spatial distance from the gear involute tooth surface to the laser displacement sensor. However, in this method, the angle between the laser beam and the normal vector of the measured tooth surface is too large, which affects the accuracy of the measurement and the stability of the data. This paper proposes an offset laser measurement method. The laser beam is offset from the center of the gear by a certain distance to form a larger incident angle with the tooth surface, which can effectively address the problem and increase the measurement accuracy. Through a selection of the optimal offset distance, the range of optimal offset measurement positions was obtained and clarified by experiments. We solved the data conversion problem caused by the change in measuring position, and we measured the pitch deviation and helix angle of the gear to confirm the feasibility of this method. According to the theoretical calculation and experimental verification, it was found that this method has the advantages of better measurement accuracy and less fluctuation in measurement data. It is, thus, suitable for precision gear measurement.
Open AccessAn Offset Laser Measurement Method for the Deviation Analysis of Cylindrical Gears
Generally, in the laser measurement of gears, the laser beam passes through the center of the gear, and the laser displacement sensor reads the spatial distance from the gear involute tooth surface to the laser displacement sensor. However, in this method, the angle between the laser beam and the normal vector of the measured tooth surface is too large, which affects the accuracy of the measurement and the stability of the data. This paper proposes an offset laser measurement method. The laser beam is offset from the center of the gear by a certain distance to form a larger incident angle with the tooth surface, which can effectively address the problem and increase the measurement accuracy. Through a selection of the optimal offset distance, the range of optimal offset measurement positions was obtained and clarified by experiments. We solved the data conversion problem caused by the change in measuring position, and we measured the pitch deviation and helix angle of the gear to confirm the feasibility of this method. According to the theoretical calculation and experimental verification, it was found that this method has the advantages of better measurement accuracy and less fluctuation in measurement data. It is, thus, suitable for precision gear measurement.