Sajag Poudel
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Sajag Poudel has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Shalabh C. Maroo
Department of Mechanical and Aerospace Engineering, Syracuse University, Syracuse, New York 13244, United States
4 shared publications - Amgad Elgowainy
Argonne National Laboratory
3 shared publications - An Zou
Shanghai Jiao Tong University
3 shared publications Krishna Reddi
3 shared publicationsAbhishek Chakrabarti
2 shared publicationsDipan Deb
2 shared publications
Latest Publications
- 13 June 2026
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 249
Techno-economic analysis of ammonia as hydrogen carrier
- 13 June 2026
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 249
Techno-economic analysis of ammonia as hydrogen carrier
- Open Access
- 28 February 2025
- Published by Elsevier in Cell Reports Sustainability
- Vol. 2 (2)
Technoeconomic analysis of distributed energy resources for rapid deployment of the US national charging network
- 28 February 2025
- Published by Elsevier in Cell Reports Sustainability
- Vol. 2 (2)
Open AccessTechnoeconomic analysis of distributed energy resources for rapid deployment of the US national charging network
- 2 March 2024
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 61, 493-502
Investigation of precooling unit design options in hydrogen refueling station for heavy-duty fuel-cell electric vehicles
- 2 March 2024
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 61, 493-502
Investigation of precooling unit design options in hydrogen refueling station for heavy-duty fuel-cell electric vehicles
- 15 April 2023
- Published by Elsevier in Applied Thermal Engineering
- Vol. 229, 120572
Single bubble nucleation in water-filled 59-nm nanochannel
- 15 April 2023
- Published by Elsevier in Applied Thermal Engineering
- Vol. 229, 120572
Single bubble nucleation in water-filled 59-nm nanochannel
- 1 September 2021
- Published by AIP Publishing in Physics of Fluids
- Vol. 33 (9) , 096105
Characteristics of shock tube generated compressible vortex rings at very high shock Mach numbers
Compressible vortex rings are usually formed at the open end of a shock tube. They show exciting flow phenomena during their formation, evolution, and propagation depending on the shock Mach number (Ms) and exit flow conditions. This study considers high shock tube pressure ratio (PR) cases showing hitherto unknown, spectacular flow structures. With hydrogen as a driver section gas at high PR, a supersonic compressible vortex ring having vortex ring Mach number (Mv) >1 is obtained for the first time. The formation of multiple triple points and the corresponding slipstream shear layers and, thus, multiple counter-rotating vortex rings (CRVRs) behind the primary vortex ring at different radial locations, in addition to the usual CRVRs, appears to be a unique characteristic for high Mach number vortex rings. During the formation stage, a vortex layer of reverse circulation than that of the primary vortex ring gets generated from the outer wall of the shock tube. The instability of such a vortex layer creates another series of opposite circulation vortices, which later interfere with the primary vortex core considerably. Also, a near stationary slipstream vortex and multiple fast-moving tiny vortices of opposite circulation to the slipstream vortex are observed near the central zone. Mechanisms for the formation of these complex vortical structures are identified. The implications of these phenomena on the vortex ring's geometric and kinematic characteristics, such as ring diameter, core diameter, circulation, and translational velocity, are discussed in detail, illustrating their differences with low vortex ring Mach number cases considering 0.31 < Mv < 1.08.
- 1 September 2021
- Published by AIP Publishing in Physics of Fluids
- Vol. 33 (9) , 096105
Characteristics of shock tube generated compressible vortex rings at very high shock Mach numbers
Compressible vortex rings are usually formed at the open end of a shock tube. They show exciting flow phenomena during their formation, evolution, and propagation depending on the shock Mach number (Ms) and exit flow conditions. This study considers high shock tube pressure ratio (PR) cases showing hitherto unknown, spectacular flow structures. With hydrogen as a driver section gas at high PR, a supersonic compressible vortex ring having vortex ring Mach number (Mv) >1 is obtained for the first time. The formation of multiple triple points and the corresponding slipstream shear layers and, thus, multiple counter-rotating vortex rings (CRVRs) behind the primary vortex ring at different radial locations, in addition to the usual CRVRs, appears to be a unique characteristic for high Mach number vortex rings. During the formation stage, a vortex layer of reverse circulation than that of the primary vortex ring gets generated from the outer wall of the shock tube. The instability of such a vortex layer creates another series of opposite circulation vortices, which later interfere with the primary vortex core considerably. Also, a near stationary slipstream vortex and multiple fast-moving tiny vortices of opposite circulation to the slipstream vortex are observed near the central zone. Mechanisms for the formation of these complex vortical structures are identified. The implications of these phenomena on the vortex ring's geometric and kinematic characteristics, such as ring diameter, core diameter, circulation, and translational velocity, are discussed in detail, illustrating their differences with low vortex ring Mach number cases considering 0.31 < Mv < 1.08.
- 12 June 2020
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 36 (27) , 7801-7807
Evaporation Dynamics in Buried Nanochannels with Micropores
Cross-connected buried nanochannels of height ∼728 nm, with micropores of ∼2 μm diameter present at each intersection, are used in this work to numerically and experimentally study droplet-coupled evaporation dynamics at room temperature. The uniformly structured channels/pores, along with their well-defined porosity, allow for computational fluid dynamics simulations and experiments to be performed on the same geometry of samples. A water droplet is placed on top of the sample causing water to wick into the nanochannels through the micropores. After advancing, the meniscus front stabilizes when evaporation flux is balanced with the wicking flux, and it recedes once the water droplet is completely wicked in. Evaporation flux at the meniscus interface of channels/pores is estimated over time, while the flux at the water droplet interface is found to be negligible. When the meniscus recedes in the channels, local contact line regions are found to form underneath the pores, thus rapidly enhancing evaporation flux as a power-law function of time. Temporal variation of wicking flux velocity and pressure gradient in the nanochannels is also independently computed, from which the viscous resistance variation is estimated and compared to the theoretical prediction.
- 12 June 2020
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 36 (27) , 7801-7807
Evaporation Dynamics in Buried Nanochannels with Micropores
Cross-connected buried nanochannels of height ∼728 nm, with micropores of ∼2 μm diameter present at each intersection, are used in this work to numerically and experimentally study droplet-coupled evaporation dynamics at room temperature. The uniformly structured channels/pores, along with their well-defined porosity, allow for computational fluid dynamics simulations and experiments to be performed on the same geometry of samples. A water droplet is placed on top of the sample causing water to wick into the nanochannels through the micropores. After advancing, the meniscus front stabilizes when evaporation flux is balanced with the wicking flux, and it recedes once the water droplet is completely wicked in. Evaporation flux at the meniscus interface of channels/pores is estimated over time, while the flux at the water droplet interface is found to be negligible. When the meniscus recedes in the channels, local contact line regions are found to form underneath the pores, thus rapidly enhancing evaporation flux as a power-law function of time. Temporal variation of wicking flux velocity and pressure gradient in the nanochannels is also independently computed, from which the viscous resistance variation is estimated and compared to the theoretical prediction.
- 5 September 2019
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 35 (39) , 12689-12693
Pool Boiling Coupled with Nanoscale Evaporation Using Buried Nanochannels
Pool boiling is explicitly coupled with nanoscale evaporation by using buried nanochannels to enhance critical heat flux (CHF) by ~105%. Additional menisci and contact line formation in nanochannels is found to be the dominant factor of CHF enhancement. Wicking assists in creating the additional contact line, but does not serve as the primary measurable factor in predicting such enhancement based on CFD simulations and wicking experiments. This work provides clarity on the roles of contact line and wicking in boiling heat transfer.
- 5 September 2019
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 35 (39) , 12689-12693
Pool Boiling Coupled with Nanoscale Evaporation Using Buried Nanochannels
Pool boiling is explicitly coupled with nanoscale evaporation by using buried nanochannels to enhance critical heat flux (CHF) by ~105%. Additional menisci and contact line formation in nanochannels is found to be the dominant factor of CHF enhancement. Wicking assists in creating the additional contact line, but does not serve as the primary measurable factor in predicting such enhancement based on CFD simulations and wicking experiments. This work provides clarity on the roles of contact line and wicking in boiling heat transfer.
- 29 August 2019
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry C
- Vol. 123 (38) , 23529-23534
Wicking in Cross-Connected Buried Nanochannels
- 29 August 2019
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry C
- Vol. 123 (38) , 23529-23534
Wicking in Cross-Connected Buried Nanochannels