Vyacheslav G. Churankin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Vyacheslav G. Churankin has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- A.M. Lasitsa2 shared publications
- Andrey A. Teploukhov
Omsk State Technical University
2 shared publications - K.N. Poleshchenko2 shared publications
- Natalya A. Semenyuk
Omsk State Technical University, Omsk, Russia
2 shared publications Omsk State Technical University
2 shared publicationsSiberian State Automobile and Highway University
2 shared publications
Latest Publications
- 13 June 2023
- Published by Novosibirsk State Technical University in Metal Working and Material Science
- Vol. 25 (2) , 6-14
Predicting the coolant lubricating properties based on its density and wetting effect
Introduction. The processes occurring in the cutting zone contribute to the rapid wear of the cutting tool and a decrease in the quality of the workpiece. It is possible to reduce the impact of negative factors during metal cutting through a rational choice of coolant. The aim of the work is to develop a methodology for the accelerated assessment of the coolant lubricating properties. Methods. Experimental studies of the lubricating effect of seven different grades of coolant, during friction of a T15K6 (15% TiC–79% WC–6% Co) hard alloy pad and a rotating roller made of carbon structural Steel 45 (0.45% C) are presented. As a parameter of coolant efficiency in terms of lubricating effect, paper proposes an efficiency coefficient Kc, which is equal to the ratio between the friction coefficient that occurs when using coolant and the friction coefficient during friction without coolant. The lower the coefficient Kc, the more effective this coolant is in terms of lubricating effect. Results. Empirical dependences of the coefficient Kc on the coolant density ρ and the limiting wetting angle Θ (Kc = f(ρ;Θ)) are established. Since the low significance of the parameter ρ is established, the formula for the dependence of the Kc only on the limiting wetting angle Θ (Kc = f(Θ)) is established in the work. It is established that the dependence formula (Kc = f(Θ) provides the highest accuracy of calculations. Discussion. After evaluating the research results presented in this paper, the following conclusions are made: 1) the paper establishes the influence of the coolant density and the limiting wetting angle on the coolant efficiency coefficient for the lubricating effect determined for the friction between a roller made of Steel 45 and a pad made of T15K6 alloy: Kc = f(ρ;Θ) and Kc = f(Θ); 2) the greatest accuracy of calculations from 2.75 to 15% is provided by the formula for the dependence Kc = f(Θ); 3) the dependence Kc = f(Θ)is proposed to be used for the method for the accelerated assessment of the coolant lubricating properties during friction of a pad made of T15K6 alloy and a rotating roller made of Steel 45. The proposed method consists in measuring the limiting wetting angle of a coolant drop on the surface of the workpiece and calculating the derived empirical dependence of the coolant efficiency coefficient on the lubricating effect.
- 13 June 2023
- Published by Novosibirsk State Technical University in Metal Working and Material Science
- Vol. 25 (2) , 6-14
Predicting the coolant lubricating properties based on its density and wetting effect
Introduction. The processes occurring in the cutting zone contribute to the rapid wear of the cutting tool and a decrease in the quality of the workpiece. It is possible to reduce the impact of negative factors during metal cutting through a rational choice of coolant. The aim of the work is to develop a methodology for the accelerated assessment of the coolant lubricating properties. Methods. Experimental studies of the lubricating effect of seven different grades of coolant, during friction of a T15K6 (15% TiC–79% WC–6% Co) hard alloy pad and a rotating roller made of carbon structural Steel 45 (0.45% C) are presented. As a parameter of coolant efficiency in terms of lubricating effect, paper proposes an efficiency coefficient Kc, which is equal to the ratio between the friction coefficient that occurs when using coolant and the friction coefficient during friction without coolant. The lower the coefficient Kc, the more effective this coolant is in terms of lubricating effect. Results. Empirical dependences of the coefficient Kc on the coolant density ρ and the limiting wetting angle Θ (Kc = f(ρ;Θ)) are established. Since the low significance of the parameter ρ is established, the formula for the dependence of the Kc only on the limiting wetting angle Θ (Kc = f(Θ)) is established in the work. It is established that the dependence formula (Kc = f(Θ) provides the highest accuracy of calculations. Discussion. After evaluating the research results presented in this paper, the following conclusions are made: 1) the paper establishes the influence of the coolant density and the limiting wetting angle on the coolant efficiency coefficient for the lubricating effect determined for the friction between a roller made of Steel 45 and a pad made of T15K6 alloy: Kc = f(ρ;Θ) and Kc = f(Θ); 2) the greatest accuracy of calculations from 2.75 to 15% is provided by the formula for the dependence Kc = f(Θ); 3) the dependence Kc = f(Θ)is proposed to be used for the method for the accelerated assessment of the coolant lubricating properties during friction of a pad made of T15K6 alloy and a rotating roller made of Steel 45. The proposed method consists in measuring the limiting wetting angle of a coolant drop on the surface of the workpiece and calculating the derived empirical dependence of the coolant efficiency coefficient on the lubricating effect.
- 27 June 2022
- Published by Nosov Magnitogorsk State Technical University in Vestnik of Nosov Magnitogorsk State Technical University
- Vol. 20 (2)
Improving the Technology of the Layer-by-Layer Formation of Nanostructured Topocomposites by Ion-Vacuum Treatment Methods Based on a Structural-Thermodynamic Approach
- 27 June 2022
- Published by Nosov Magnitogorsk State Technical University in Vestnik of Nosov Magnitogorsk State Technical University
- Vol. 20 (2)
Improving the Technology of the Layer-by-Layer Formation of Nanostructured Topocomposites by Ion-Vacuum Treatment Methods Based on a Structural-Thermodynamic Approach
- 1 November 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Dynamics of wear surface layers modified by complex treatment
The paper proposes an integrated method for processing the surface layer. Joint application of ion implantation and surface plastic deformation is considered. An efficient model for predicting the wear resistance of the surface layer is proposed. The results of friction's tests are submitted.
- 1 November 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Dynamics of wear surface layers modified by complex treatment
The paper proposes an integrated method for processing the surface layer. Joint application of ion implantation and surface plastic deformation is considered. An efficient model for predicting the wear resistance of the surface layer is proposed. The results of friction's tests are submitted.
- 1 May 2007
- Published by Springer Nature in Chemical and Petroleum Engineering
- Vol. 43 (5-6) , 275-279
Nanotechnology in compressor and pump engineering
- 1 May 2007
- Published by Springer Nature in Chemical and Petroleum Engineering
- Vol. 43 (5-6) , 275-279
Nanotechnology in compressor and pump engineering