Jinho Ko
Jinho Ko has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Sang-Gug Lee
School of Electrical Engineering, Korea Advanced Institute of Science and Technology, Daejeon, South Korea
10 shared publications - Kyung-Sik Choi
Yonsei University
9 shared publications - Keun-Mok Kim
School of Electrical Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon, South Korea
8 shared publications - Jusung Kim
Ewha Womans University
4 shared publications - Subin Kim
PHYCHIPS Inc., Daejeon 34025, South Korea
4 shared publications - Hyunki Jung
School of Electrical Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon, South Korea
3 shared publications
Latest Publications
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 9, 133-136
A Multiband Ultralow-Power Transceiver With Two-Step Wake-Up Reception
This paper presents a multi-band fully integrated ultra-low-power (ULP) transceiver with a two-step wake-up receiver (WuRX) and switched-capacitor (SC) based high-efficiency transmitter. Operating from 200 MHz to 1 GHz, the transceiver covers most IoT applications on a single chip. By employing a novel two-step wake-up scheme with a rotating correlator, the proposed ULP WuRX consumes only 6.7 μW in duty-cycling mode while achieving -125 dBm and -120 dBm sensitivities at 200 MHz and 1 GHz, respectively, with less than 10% packet error rate. The switched-capacitor power amplifier (SCPA)-based transmitter offers a 40.8 dB dynamic range (-30 to 10.8 dBm) and 40.9% maximum efficiency at 200 MHz, with precise linear variable gain. The RX and TX share a local oscillator signal from a wide frequency-range fractional-N PLL. Implemented in 55-nm CMOS, the transceiver occupies 2.6 mm × 4.7 mm. The radio supports BFSK modulation with data rates up to 1 Mbps.
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 9, 133-136
A Multiband Ultralow-Power Transceiver With Two-Step Wake-Up Reception
This paper presents a multi-band fully integrated ultra-low-power (ULP) transceiver with a two-step wake-up receiver (WuRX) and switched-capacitor (SC) based high-efficiency transmitter. Operating from 200 MHz to 1 GHz, the transceiver covers most IoT applications on a single chip. By employing a novel two-step wake-up scheme with a rotating correlator, the proposed ULP WuRX consumes only 6.7 μW in duty-cycling mode while achieving -125 dBm and -120 dBm sensitivities at 200 MHz and 1 GHz, respectively, with less than 10% packet error rate. The switched-capacitor power amplifier (SCPA)-based transmitter offers a 40.8 dB dynamic range (-30 to 10.8 dBm) and 40.9% maximum efficiency at 200 MHz, with precise linear variable gain. The RX and TX share a local oscillator signal from a wide frequency-range fractional-N PLL. Implemented in 55-nm CMOS, the transceiver occupies 2.6 mm × 4.7 mm. The radio supports BFSK modulation with data rates up to 1 Mbps.
- 13 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 58 (6) , 1667-1680
A −124-dBm Sensitivity Interference-Resilient Direct-Conversion Duty-Cycled Wake-Up Receiver Achieving 0.114 mW at 1.966-s Wake-Up Latency
This article presents an interference-resilient high-sensitivity binary frequency-shift keying (BFSK) multi-channel wake-up receiver (WuRX) supporting 900-MHz bands for low-power wide-area network (LPWAN) applications. The proposed WuRX uses a direct-conversion architecture, a frequency-to-energy demodulator, and a 4096-bit correlator. Direct conversion using a 50%-to-25% duty-cycle conversion mixer and two-stage ring voltage-controlled oscillator (VCO) minimizes the power consumption. The frequency-to-energy demodulator offers a process-voltage-temperature (PVT) variation-tolerant symbol recovery based on an image rejection $n$ -path filter (IRNF), a poly-phase filter (PPF), and a quadrature envelope detector (ED). The 4096-bit correlator provides a digital processing gain of about 17 dB, improving both the sensitivity and the selectivity. To reduce the power consumption further, the proposed WuRX supports an asynchronous duty-cycling operation based on repetition of the wake-up code. Implemented in the 55-nm complementary metal–oxide–semiconductor (CMOS), the proposed WuRX achieves sensitivity of −124 dBm in the always-on mode while dissipating 781 $\mu \text{W}$ . For the duty-cycling mode with wake-up codes repeated 15 times, the proposed WuRX exhibits the same sensitivity of −124 dBm with reduced power consumption of 114 $\mu \text{W}$ and extended wake-up latency of 1.966 s. The proposed WuRX shows robust interference resilience with a signal-to-interference ratio (SIR) of −76 dB at a 20-MHz offset against a continuous wave (CW). The CMOS radio module, including the proposed WuRX, showed packet-error rates (PERs) of 0% and 5.7% in the 4.8- and 9.8-km ground-to-ground wireless communication tests, respectively.
- 13 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 58 (6) , 1667-1680
A −124-dBm Sensitivity Interference-Resilient Direct-Conversion Duty-Cycled Wake-Up Receiver Achieving 0.114 mW at 1.966-s Wake-Up Latency
This article presents an interference-resilient high-sensitivity binary frequency-shift keying (BFSK) multi-channel wake-up receiver (WuRX) supporting 900-MHz bands for low-power wide-area network (LPWAN) applications. The proposed WuRX uses a direct-conversion architecture, a frequency-to-energy demodulator, and a 4096-bit correlator. Direct conversion using a 50%-to-25% duty-cycle conversion mixer and two-stage ring voltage-controlled oscillator (VCO) minimizes the power consumption. The frequency-to-energy demodulator offers a process-voltage-temperature (PVT) variation-tolerant symbol recovery based on an image rejection $n$ -path filter (IRNF), a poly-phase filter (PPF), and a quadrature envelope detector (ED). The 4096-bit correlator provides a digital processing gain of about 17 dB, improving both the sensitivity and the selectivity. To reduce the power consumption further, the proposed WuRX supports an asynchronous duty-cycling operation based on repetition of the wake-up code. Implemented in the 55-nm complementary metal–oxide–semiconductor (CMOS), the proposed WuRX achieves sensitivity of −124 dBm in the always-on mode while dissipating 781 $\mu \text{W}$ . For the duty-cycling mode with wake-up codes repeated 15 times, the proposed WuRX exhibits the same sensitivity of −124 dBm with reduced power consumption of 114 $\mu \text{W}$ and extended wake-up latency of 1.966 s. The proposed WuRX shows robust interference resilience with a signal-to-interference ratio (SIR) of −76 dB at a 20-MHz offset against a continuous wave (CW). The CMOS radio module, including the proposed WuRX, showed packet-error rates (PERs) of 0% and 5.7% in the 4.8- and 9.8-km ground-to-ground wireless communication tests, respectively.
- 27 June 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 69 (10) , 4083-4087
CMOS Fractional-N Frequency Synthesizer for UHF RFID Reader Applications With Transformer-Based ISF Manipulation VCO
This brief presents the CMOS fractional-N frequency synthesizer for UHF RFID reader applications. With stringent phase noise (PN) specifications for UHF RFID transceiver, our proposed synthesizer is designed to have a narrow loop bandwidth and $2^{nd}$ -order loop filter as the optimum solution paired with low noise VCO. Then, we propose the transformer-based impulse sensitivity function (ISF) manipulating VCO that supports the target PN of the frequency synthesizer, albeit with large pass-band characteristic. Compared to conventional ISF manipulating VCO, our proposed solution improves the PN by 11.3 and 14.7 dB at 10 kHz and 1 MHz offset frequencies, respectively. Figure of merit (FOM) is also superior to conventional one by 7.4 and 10.9 dB at aforementioned offset frequencies. The frequency synthesizer is implemented in a 55nm CMOS technology as a part of the UHF RFID transmitter and consumes 38.4 mW power with 0.413 $mm^{2}$ active area. With comparison to the state-of-the-art frequency synthesizer at sub-6GHz operating frequency, only our solution satisfies the target PN for EPC global standard and various local regulations across the entire UHF RFID operating frequency range.
- 27 June 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 69 (10) , 4083-4087
CMOS Fractional-N Frequency Synthesizer for UHF RFID Reader Applications With Transformer-Based ISF Manipulation VCO
This brief presents the CMOS fractional-N frequency synthesizer for UHF RFID reader applications. With stringent phase noise (PN) specifications for UHF RFID transceiver, our proposed synthesizer is designed to have a narrow loop bandwidth and $2^{nd}$ -order loop filter as the optimum solution paired with low noise VCO. Then, we propose the transformer-based impulse sensitivity function (ISF) manipulating VCO that supports the target PN of the frequency synthesizer, albeit with large pass-band characteristic. Compared to conventional ISF manipulating VCO, our proposed solution improves the PN by 11.3 and 14.7 dB at 10 kHz and 1 MHz offset frequencies, respectively. Figure of merit (FOM) is also superior to conventional one by 7.4 and 10.9 dB at aforementioned offset frequencies. The frequency synthesizer is implemented in a 55nm CMOS technology as a part of the UHF RFID transmitter and consumes 38.4 mW power with 0.413 $mm^{2}$ active area. With comparison to the state-of-the-art frequency synthesizer at sub-6GHz operating frequency, only our solution satisfies the target PN for EPC global standard and various local regulations across the entire UHF RFID operating frequency range.
- 12 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 57 (11) , 3336-3347
A 915 MHz IoT Transmitter Employing Frequency Tripler and Digitally Controlled Duty-Cycle/Phase Calibration
A 915 MHz binary frequency-shift keying (BFSK) transmitter (TX) for Internet-of-Things (IoT) applications is presented. The proposed TX adopts a passive frequency tripler, digital duty-cycle/phase calibration, and a low-cost on-chip power amplifier (PA) matching network (MN). The frequency tripler allows an ultralow-power (ULP) implementation of the frequency synthesizer by lowering the maximum operating frequency and relaxing the frequency tuning range requirement. The proposed frequency tripler provides 10.6 dB better 300 MHz spur reduction compared to that of the conventional frequency tripler by adding a series high-pass filter. The two-phase 20% duty-cycle and single-ended 50% duty-cycle calibration circuits drive the frequency tripler and Class-D PA, respectively, suppressing unwanted spurs significantly. The digital duty-cycle/phase calibration circuits, designed based on the quantitative analysis of the stability, offer advantage of technology scaling. The reduced spur relaxes the harmonic filtering requirement at the PA output, leading to an on-chip PA MN with low- ${Q}$ . Implemented in 55 nm CMOS, the proposed TX shows the peak output power of 5.2 dBm and efficiency of 30.6% over 902–928 MHz while dissipating 210 $\mu \text{W}$ in the phase-locked loop (PLL) for 0.9 V supply. All spur component levels stay below −41 dBm with the worst harmonic distortion of −48.5 dBc. The proposed TX achieves 100 kbps of data rate for the BFSK modulated signals with the corresponding FSK error of 3.2%.
- 12 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 57 (11) , 3336-3347
A 915 MHz IoT Transmitter Employing Frequency Tripler and Digitally Controlled Duty-Cycle/Phase Calibration
A 915 MHz binary frequency-shift keying (BFSK) transmitter (TX) for Internet-of-Things (IoT) applications is presented. The proposed TX adopts a passive frequency tripler, digital duty-cycle/phase calibration, and a low-cost on-chip power amplifier (PA) matching network (MN). The frequency tripler allows an ultralow-power (ULP) implementation of the frequency synthesizer by lowering the maximum operating frequency and relaxing the frequency tuning range requirement. The proposed frequency tripler provides 10.6 dB better 300 MHz spur reduction compared to that of the conventional frequency tripler by adding a series high-pass filter. The two-phase 20% duty-cycle and single-ended 50% duty-cycle calibration circuits drive the frequency tripler and Class-D PA, respectively, suppressing unwanted spurs significantly. The digital duty-cycle/phase calibration circuits, designed based on the quantitative analysis of the stability, offer advantage of technology scaling. The reduced spur relaxes the harmonic filtering requirement at the PA output, leading to an on-chip PA MN with low- ${Q}$ . Implemented in 55 nm CMOS, the proposed TX shows the peak output power of 5.2 dBm and efficiency of 30.6% over 902–928 MHz while dissipating 210 $\mu \text{W}$ in the phase-locked loop (PLL) for 0.9 V supply. All spur component levels stay below −41 dBm with the worst harmonic distortion of −48.5 dBc. The proposed TX achieves 100 kbps of data rate for the BFSK modulated signals with the corresponding FSK error of 3.2%.
- 27 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 57 (3) , 892-905
A 0.3-to-1-GHz IoT Transmitter Employing Pseudo-Randomized Phase Switching Modulator and Single-Supply Class-G Harmonic Rejection PA
A wideband Internet of Things (IoT) transmitter (TX) employing open-loop binary frequency-shift keying (BFSK) modulator with a pseudo-randomized phase transition (PRPT) time and a single-supply Class-G harmonic rejection (HR) power amplifier (PA) is presented. The proposed open-loop phase switching modulator eliminates the data-rate limitation in a conventional phase-locked loop (PLL)-based closed-loop modulator, while the PRPT scheme increases the effective phase resolution with a better power efficiency than delta–sigma modulation (DSM)-based randomization. Thus, a low spur level below −40 dBc is achieved with only a 4-bit phase resolution. The Class-G HR PA, including a four-level supply voltage waveform generator, is proposed as a high-efficiency and low spurious PA architecture. The proposed HR PA presents the third- and fifth-harmonics cancellation over the 0.3-to-1-GHz band, while only a single supply is required for Class-G implementation of the HR PA. The proposed BFSK TX is implemented in a 55-nm CMOS process. Measured with a 0.3-to-1-GHz continuous-wave carrier, TX output power and PA drain efficiency are 2.7 ± 0.2 dB and 52% ± 3%, respectively, operating from a 0.9-V supply. The HRs of −31.4/−42.7 and −28.2/−42.4 dBc at the third/fifth harmonics are measured at the lowest (0.3 GHz) and the highest (1 GHz) carrier frequencies, respectively. With a data rate of 1 Mb/s, the measured FSK errors are 3.6% and 4.2% at both ends of the operating frequency.
- 27 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 57 (3) , 892-905
A 0.3-to-1-GHz IoT Transmitter Employing Pseudo-Randomized Phase Switching Modulator and Single-Supply Class-G Harmonic Rejection PA
A wideband Internet of Things (IoT) transmitter (TX) employing open-loop binary frequency-shift keying (BFSK) modulator with a pseudo-randomized phase transition (PRPT) time and a single-supply Class-G harmonic rejection (HR) power amplifier (PA) is presented. The proposed open-loop phase switching modulator eliminates the data-rate limitation in a conventional phase-locked loop (PLL)-based closed-loop modulator, while the PRPT scheme increases the effective phase resolution with a better power efficiency than delta–sigma modulation (DSM)-based randomization. Thus, a low spur level below −40 dBc is achieved with only a 4-bit phase resolution. The Class-G HR PA, including a four-level supply voltage waveform generator, is proposed as a high-efficiency and low spurious PA architecture. The proposed HR PA presents the third- and fifth-harmonics cancellation over the 0.3-to-1-GHz band, while only a single supply is required for Class-G implementation of the HR PA. The proposed BFSK TX is implemented in a 55-nm CMOS process. Measured with a 0.3-to-1-GHz continuous-wave carrier, TX output power and PA drain efficiency are 2.7 ± 0.2 dB and 52% ± 3%, respectively, operating from a 0.9-V supply. The HRs of −31.4/−42.7 and −28.2/−42.4 dBc at the third/fifth harmonics are measured at the lowest (0.3 GHz) and the highest (1 GHz) carrier frequencies, respectively. With a data rate of 1 Mb/s, the measured FSK errors are 3.6% and 4.2% at both ends of the operating frequency.
- 7 April 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 56 (9) , 2656-2667
A –123-dBm Sensitivity Split-Channel BFSK Reconfigurable Data/Wake-Up Receiver for Low-Power Wide-Area Networks
A 900-MHz high-sensitivity split-channel binary frequency-shift keying (SC-BFSK) reconfigurable data/wake-up receiver (RX) for low-power wide-area networks (LPWANs) is presented. In the data mode, the proposed RX demodulates data through the RF/analog front end (RXFE), the analog-to-digital converter (ADC), and the modulator-demodulator (MODEM). The MODEM implemented in the external microcontroller unit (MCU) applies additional digital signal processing to improve about 17-dB sensitivity. In the wake-up mode, the proposed RX saves the power dissipation by turning off all blocks except for the RXFE and wake-up preamble detector (WuPD). The WuPD following the RXFE provides a 17-dB sensitivity improvement in place of the MODEM of the data RX. Adopting the proposed SC-BFSK, in which other channels are inter-allocated between the BFSK tones of one channel, increases the number of channels while taking advantage of wide tone spacing, which improves the bit error rate (BER) in a multipath fading channel. To implement the ultra-low-power (ULP) SC-BFSK RX, the RXFE employs the 2:1 LO sliding-IF architecture and a band-pass filter (BPF)-based frequency-to-energy detection baseband demodulator. Implemented in 55-nm CMOS, the proposed RX, including both data and wake-up RXs, exhibits -123-dBm sensitivity with 0.39-kbps data rate and 81.92-ms wake-up latency, while the RX chip dissipates 0.88 mW.
- 7 April 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 56 (9) , 2656-2667
A –123-dBm Sensitivity Split-Channel BFSK Reconfigurable Data/Wake-Up Receiver for Low-Power Wide-Area Networks
A 900-MHz high-sensitivity split-channel binary frequency-shift keying (SC-BFSK) reconfigurable data/wake-up receiver (RX) for low-power wide-area networks (LPWANs) is presented. In the data mode, the proposed RX demodulates data through the RF/analog front end (RXFE), the analog-to-digital converter (ADC), and the modulator-demodulator (MODEM). The MODEM implemented in the external microcontroller unit (MCU) applies additional digital signal processing to improve about 17-dB sensitivity. In the wake-up mode, the proposed RX saves the power dissipation by turning off all blocks except for the RXFE and wake-up preamble detector (WuPD). The WuPD following the RXFE provides a 17-dB sensitivity improvement in place of the MODEM of the data RX. Adopting the proposed SC-BFSK, in which other channels are inter-allocated between the BFSK tones of one channel, increases the number of channels while taking advantage of wide tone spacing, which improves the bit error rate (BER) in a multipath fading channel. To implement the ultra-low-power (ULP) SC-BFSK RX, the RXFE employs the 2:1 LO sliding-IF architecture and a band-pass filter (BPF)-based frequency-to-energy detection baseband demodulator. Implemented in 55-nm CMOS, the proposed RX, including both data and wake-up RXs, exhibits -123-dBm sensitivity with 0.39-kbps data rate and 81.92-ms wake-up latency, while the RX chip dissipates 0.88 mW.
- 5 April 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 31 (6) , 604-607
An Active Leakage Canceller Adopting Switched-Capacitor Digital Power Amplifier for UHF-RFID Transceiver
A low-noise active leakage canceller (ALC) for radio frequency identification (RFID) transceiver is reported. The proposed ALC suppresses the strong transmitter (TX) leakage at the receiver (RX) input through continuous leakage tracking by employing an I/Q harmonic rejection switched-capacitor digital power amplifier (I/Q HR SC DPA). Compared to the analog feedback loop-based ALC, the proposed ALC minimizes the noise figure (NF) degradation in the RX and eliminates the large-size passive components in the analog low pass filter, which leads to high RX sensitivity and small chip area. Implemented in a 55-nm CMOS, the proposed ALC suppresses -10 dBm TX leakage down to -47.2 dBm while degrading the RX NF by 0.4 dB at the offset frequency of 640 kHz.
- 5 April 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 31 (6) , 604-607
An Active Leakage Canceller Adopting Switched-Capacitor Digital Power Amplifier for UHF-RFID Transceiver
A low-noise active leakage canceller (ALC) for radio frequency identification (RFID) transceiver is reported. The proposed ALC suppresses the strong transmitter (TX) leakage at the receiver (RX) input through continuous leakage tracking by employing an I/Q harmonic rejection switched-capacitor digital power amplifier (I/Q HR SC DPA). Compared to the analog feedback loop-based ALC, the proposed ALC minimizes the noise figure (NF) degradation in the RX and eliminates the large-size passive components in the analog low pass filter, which leads to high RX sensitivity and small chip area. Implemented in a 55-nm CMOS, the proposed ALC suppresses -10 dBm TX leakage down to -47.2 dBm while degrading the RX NF by 0.4 dB at the offset frequency of 640 kHz.
- 17 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 68 (8) , 2810-2814
A Low-Noise and Fast-Settling UHF RFID Receiver With Digitally Controlled Leakage Cancellation
UHF RFID reader suffers from a strong transmitter (Tx) leakage signal coupled to a receiver (Rx), especially for an area-compact single-antenna implementation. Then, several Tx leakage cancellation schemes have been developed not to saturate the Rx and to minimize the performance degradation. This brief proposes a UHF RFID reader Rx with a low noise performance and a fast settling time by employing a digitally controlled leakage cancellation method in both passive and active realizations. A digitally-controlled passive vector reflector enhances the Tx to Rx isolation ratio by providing the optimum load impedance. An active anti-leakage feedback loop adaptively tracks the time-varying leakage and generate the phase-inverted leakage replica to suppress the leakage. The prototype chip is fabricated in a CMOS 55 nm process and the area of the chip is 2.1 mm × 1.8 mm. The passive leakage cancellation (PLC) with a vector reflector endures the 1 dBm leakage with a low Rx noise figure of 12.5 dB and 35.7 mW power consumption. The active leakage cancellation (ALC) with an anti-leakage feedback loop covers 6 dBm leakage with a fast settling time of 4.6μs and 58 mW power consumption.
- 17 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 68 (8) , 2810-2814
A Low-Noise and Fast-Settling UHF RFID Receiver With Digitally Controlled Leakage Cancellation
UHF RFID reader suffers from a strong transmitter (Tx) leakage signal coupled to a receiver (Rx), especially for an area-compact single-antenna implementation. Then, several Tx leakage cancellation schemes have been developed not to saturate the Rx and to minimize the performance degradation. This brief proposes a UHF RFID reader Rx with a low noise performance and a fast settling time by employing a digitally controlled leakage cancellation method in both passive and active realizations. A digitally-controlled passive vector reflector enhances the Tx to Rx isolation ratio by providing the optimum load impedance. An active anti-leakage feedback loop adaptively tracks the time-varying leakage and generate the phase-inverted leakage replica to suppress the leakage. The prototype chip is fabricated in a CMOS 55 nm process and the area of the chip is 2.1 mm × 1.8 mm. The passive leakage cancellation (PLC) with a vector reflector endures the 1 dBm leakage with a low Rx noise figure of 12.5 dB and 35.7 mW power consumption. The active leakage cancellation (ALC) with an anti-leakage feedback loop covers 6 dBm leakage with a fast settling time of 4.6μs and 58 mW power consumption.
- 21 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 56 (6) , 1849-1858
A Sub-nW Single-Supply 32-kHz Sub-Harmonic Pulse Injection Crystal Oscillator
An extremely low-power 32-kHz crystal oscillator (XO) based on a sub-harmonic pulse injection technique is presented. By injecting current pulses into the crystal at the sub-harmonic of the oscillation frequency, the power consumption of the proposed XO reduces with an increase in the order of sub-harmonic (N). For the generation of sub-harmonic pulses with accurate timing, a 50%-duty-cycle-locked loop and a sub-harmonic peak-detection delay-locked loop are employed. A clock divider is also utilized to generate the sub-harmonic clock, which is required for the real-time clock as well. Implemented in a 55-nm CMOS technology with a triple well, the proposed XO, including a clock divider, dissipates 0.74 nW from a single 0.3-V supply for N = 16 and the chip occupies only 0.019 mm².
- 21 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 56 (6) , 1849-1858
A Sub-nW Single-Supply 32-kHz Sub-Harmonic Pulse Injection Crystal Oscillator
An extremely low-power 32-kHz crystal oscillator (XO) based on a sub-harmonic pulse injection technique is presented. By injecting current pulses into the crystal at the sub-harmonic of the oscillation frequency, the power consumption of the proposed XO reduces with an increase in the order of sub-harmonic (N). For the generation of sub-harmonic pulses with accurate timing, a 50%-duty-cycle-locked loop and a sub-harmonic peak-detection delay-locked loop are employed. A clock divider is also utilized to generate the sub-harmonic clock, which is required for the real-time clock as well. Implemented in a 55-nm CMOS technology with a triple well, the proposed XO, including a clock divider, dissipates 0.74 nW from a single 0.3-V supply for N = 16 and the chip occupies only 0.019 mm².
- 4 September 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 50 (10) , 2294-2305
A 50–450 MHz Tunable RF Biquad Filter Based on a Wideband Source Follower With > 26 dBm IIP$_{3}$, +12 dBm P$_{1{\rm dB}}$, and 15 dB Noise Figure
This paper reports a source follower-based active RC filter topology for RF front-ends in wideband systems. In the proposed active RC filter, the noise figure and bandwidth are improved through adopting the proposed sub-1 Ω Z out source follower, which replaces the conventional operational amplifier-based unity gain buffer and through simply changing its location in the filter. Applying the proposed scheme to the conventional Sallen-Key filter also improves the stopband rejection performance. Furthermore, the proposed filter topology ultimately suppresses the DC offset voltage and flicker noise of the unity gain buffer, which is the only active circuit in the filter. The proposed biquad filter is implemented in 0.18 μm CMOS and the measurements exhibit >26 dBm IIP 3 , +12 dBm input P 1dB , and 15 dB noise figure over 50-450 MHz of a 6 bit tunable frequency range. The proposed biquad filter consumes 14 mA from a 1.8 V supply and the chip occupies 1000 ×500 μm 2 .
- 4 September 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 50 (10) , 2294-2305
A 50–450 MHz Tunable RF Biquad Filter Based on a Wideband Source Follower With > 26 dBm IIP$_{3}$, +12 dBm P$_{1{\rm dB}}$, and 15 dB Noise Figure
This paper reports a source follower-based active RC filter topology for RF front-ends in wideband systems. In the proposed active RC filter, the noise figure and bandwidth are improved through adopting the proposed sub-1 Ω Z out source follower, which replaces the conventional operational amplifier-based unity gain buffer and through simply changing its location in the filter. Applying the proposed scheme to the conventional Sallen-Key filter also improves the stopband rejection performance. Furthermore, the proposed filter topology ultimately suppresses the DC offset voltage and flicker noise of the unity gain buffer, which is the only active circuit in the filter. The proposed biquad filter is implemented in 0.18 μm CMOS and the measurements exhibit >26 dBm IIP 3 , +12 dBm input P 1dB , and 15 dB noise figure over 50-450 MHz of a 6 bit tunable frequency range. The proposed biquad filter consumes 14 mA from a 1.8 V supply and the chip occupies 1000 ×500 μm 2 .