CJChiyu Jiao

Chiyu Jiao

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Chiyu Jiao has a total of 32 co-authors. Here are the top co-authors by number of shared publications:

  • Luyu Liu

    Assistant Professor, Beijing University of Civil Engineering and Architecture, Xicheng, Beijing, 100044, China

    2 shared publications
  • Peiheng Long

    School of Civil and Transportation Engineering, Beijing University of Civil Engineering and Architecture, Beijing, China

    2 shared publications
  • Yu Zhang

    Lecturer and Graduate Student, School of Civil Engineering, Beijing University of Civil Engineering and Architecture, Beijing 100044, China

    2 shared publications
  • Biao Wei

    School of Civil Engineering, Central South University, Changsha, China

    1 shared publication
  • Chenyu Wang

    School of Civil and Transportation Engineering, Beijing University of Civil Engineering and Architecture, Beijing, China

    1 shared publication
  • Gexi Zhu

    Beijing Xinqiao Technology Development Co., Ltd, Beijing, China

    1 shared publication

Latest Publications

  • Open Access

    Interpretable Machine Learning for Predicting Residual Drift Ratios in Reinforced Concrete Bridge Piers

    by Min Zhang, Xuefeng Zhang, Liangjun Li, Chiyu Jiao

    Accurate prediction of the residual drift ratio of reinforced concrete bridge piers is challenging because conventional methods are computationally expensive, time-consuming, and unable to effectively capture complex nonlinear interactions among multiple influencing factors. To address these limitations, this study proposes an interpretable machine learning framework for predicting the residual drift ratio of reinforced concrete bridge piers. A comprehensive database containing 261 quasi-static experimental datasets was established, incorporating key structural and material parameters, including axial com-pression ratio, shear span ratio, stirrup ratio, longitudinal reinforcement ratio, material strengths, and geometric dimensions. Based on this database, six representative machine learning models were developed and systematically compared. Their predictive performance, robustness, and generalization capability were evaluated using multiple statistical metrics and Monte Carlo simulations. The results show that the CatBoost model consistently outperformed the other models, achieving an R2 value of 0.9629 on the test set while maintaining excellent stability under random data partitions. Furthermore, SHAP analysis was employed to interpret the trained model and quantify the contributions of individual input variables. Eight key factors influencing the residual drift ratio were identified, with the loading displacement ratio (θ) exhibiting the greatest influence. These findings demonstrate that the proposed framework provides an accurate, reliable, and interpretable tool for predicting the post-earthquake residual drift ratio of reinforced concrete bridge piers, offering valuable support for performance-based seismic design, post-earthquake damage assessment, and resilience-based bridge engineering.

  • Open Access

    Study on the additional support length requirements of single-span bridges due to skew using a simplified method

    by Suiwen Wu, Junfeng Jia, Chiyu Jiao, Junfei Huang, Jianzhong Li

    Skew bridges with seat-type abutments are frequently unseated in earthquakes due to large transverse displacements at their acute corners. It is believed these large displacements are due to in-plane rotation of the superstructure. Lack of detailed guidelines for modeling of skew bridges, many current design codes give empirical expressions rather than theoretical solutions for the additional support length required in skew bridges to prevent unseating. In this paper, a parametric study has been carried out to study the influence of skew angle, aspect ratio and fundamental periods of bridges on the additional support length requirements of single-span bridges due to skew using a shake table experiment validated Simplified Method, which is capable of simulating gap closure based on response spectrum analysis. This method is developed based on the premise that the obtuse corner of the superstructure engages the adjacent back wall during lateral loading and rotates about this corner until the loading reverses direction. A design response spectrum specified in AASHTO LRFD Specifications was employed to represent the design-level earthquakes. The results show the additional length required to prevent unseating due to skew increases with the skew angle in an approximately linear manner when the angle is less than a critical value and decreases for angles above this value. This critical skew angle increases with the aspect ratio approximately in a linear manner and shows negligible dependence on the fundamental periods of the bridges, and combination of span length and width. In addition, the critical skew angle varies between 58° and 66°, when the aspect ratio is varied from 3.0 to 5.0. The results also show that the empirical formulas for minimum support length requirements of skew bridges in current codes and specifications can not accurately reflect the influence of skew.


  • Open Access

    Damage Detection and Analysis of Urban Bridges Using Terrestrial Laser Scanning (TLS), Ground-Based Microwave Interferometry, and Permanent Scatterer Interferometry Synthetic Aperture Radar (PS-InSAR)

    by Xianglei Liu, Peipei Wang, Zhao Lu, Kai Gao, Hui Wang, Chiyu Jiao, Xuedong Zhang

    This paper presents a practical framework for urban bridge damage detection and analysis by using three key techniques: terrestrial laser scanning (TLS), ground-based microwave interferometry, and permanent scatterer interferometry synthetic aperture radar (PS-InSAR). The proposed framework was tested on the Beishatan Bridge in Beijing, China. Firstly, a Digital Surface Model (DSM) of the lower surface of the bridge was constructed based on the point cloud generated by using TLS to obtain the potential damage area. Secondly, the dynamic time-series displacement of the potential damage area was acquired by ground-based microwave interferometry, and the Extreme-Point Symmetric Mode Decomposition (ESMD) method was applied to detect damages by the use of signal decomposition and instantaneous frequency calculation. Lastly, the PS-InSAR technique was applied to obtain the surface deformation around Beishatan Bridge by using COSMO-SkyMed images with a ground resolution of 3 m × 3 m, and finally, we analyzed the causes of bridge damage. The experimental results showed that the proposed framework can effectively obtain the potential damage area of the bridge by the DSM from the point cloud by TLS and further judge whether the bridge was damaged by the ESMD method, based on the time-series displacement data. The results also showed that the subway shield construction may be the reason for damage to Beishatan Bridge.


  • The Advantages of the Analysis of Curved Box Beam Using the Grillage Method

    by Chiyu Jiao, Yu Zhang, Shilun Hao

    This paper first introduces the basic principles and stimulation methods of the grillage method, using such method to conduct stimulation analysis of a certain curved beam bridge—a ramp bridge of Jingkai Road in Beijing—as its engineering background. By using MIDAS/CIVIL, a software finite element method to analyze structures, a single beam model and grillage method model were built, and the comparisons and the analysis about deflection and stress among these models was conducted. The conclusion indicates that the calculation results obtained from the grillage method are closer to the values required in actual construction. The analysis revealed that the models based on the grillage method can reflect the mechanical properties and stress state more efficiently and accurately. Therefore, the grillage method is a very convenient and practical method for analyzing urban curved beam bridges, and it is verified that it can be used in the analysis of urban curved bridges.

  • Comparison Study on Seismic Performance of Different Structural Forms for Urban Expressway Viaducts

    by Chiyu Jiao, Peiheng Long, Luyu Liu, Yu Zhang

    Many structure forms can be chosen when designing an urban expressway viaduct. To get an optimal structure, a comparison study on the seismic performance of different structural forms for urban expressway viaducts should be done carefully. Taking multi-span, simply-supported, small box girders as a basic structure type, a double column pier and double pile cap structure (DCPDPC), adouble column pier and single pile cap structure(DCPSPC), and a single column pier and single pile cap structure (SCPSPC) were chosen as substructures of the same bridge. Seismic performances — such as deformation capacity of bearings, bending capacity and shearing capacity of piers and piles in common earthquakes, and ductile capacity of piers under rare earthquakes of different structural forms — were compared by the demand capacity ratio method. The optimal structures are discussed herein. It can be concluded that the structural form of DCPDPC and DCPSPC have better advantages than others, and the SCPSPC has poor seismic performance and should be carefully used when designing an urban expressway viaduct. This research provides good technical support for the conceptual design for urban expressway viaducts.

  • Creeping Mechanism Analysis of Curved Bridges

    by Chiyu Jiao, Luyu Liu, Peiheng Long, Suwei Hou

    Creeping diseases can reduce driving comfort and endanger structural safety, so it is necessary to analyze the causes of creeping. Based on existing research, the factors of the creeping phenomenon using TianNingSi overpass as an example related to the features of radial displacement under dead load, live load, concrete shrinkage and creep, temperature, prestress, etc., were analyzed. The study shows that centrifugal force is the main cause of creeping in curved bridges, which have heavy traffic and large curvature radii. The deficiencies in infrastructure and bearing form should be the main cause of creeping disease. Bearing form optimization can prevent creeping diseases.