Lorenzo Pimpolari
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Lorenzo Pimpolari has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
Cinzia Casiraghi
Department of Chemistry, University of Manchester, Manchester, U.K.
2 shared publicationsGianluca Fiori
Dipartimento di Ingegneria dellInformazione, University of Pisa, Pisa, Italy
2 shared publicationsMassimo Macucci
Dipartimento di Ingegneria dellInformazione, University of Pisa, Pisa, Italy
2 shared publicationsDmitry K. Polyushkin
Institute of Photonics Vienna University of Technology Vienna 1040 Austria
1 shared publication- Francesco Pieri
Dipartimento di Ingegneria dell'Informazione Università di Pisa Pisa Italy
1 shared publication Gabriele Calabrese
Dipartimento di Ingegneria dell'Informazione Università di Pisa Via Girolamo Caruso 16 Pisa 56122 Italy
1 shared publication
Latest Publications
- Open Access
- 21 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal on Flexible Electronics
- Vol. 1 (3) , 153-158
Fully Printed and Flexible Schottky Diodes Based on Carbon Nanomaterials Operating Up to 5 MHz
The capability to fabricate printed and flexible energy harvesting and conditioning circuits, over large area and with low-cost techniques, is crucial to enable flexible and wearable electronics. Carbon nanomaterials show excellent electrical, optical, chemical, and mechanical properties for printed electronics, offering low-cost, and large-area functionality on flexible substrates. In the past few years many efforts have been dedicated to the fabrication of printed transistors made with carbon nanomaterials, but very few works have been dedicated to diodes, which are fundamental circuit elements, often employed in energy harvesting systems. Here we report a simple and cost-effective approach for the fabrication of fully inkjet printed Schottky diodes on Kapton and paper substrates using carbon nanotubes and graphene. We demonstrate that both ohmic and Schottky contacts between printed nanotubes and graphene can be obtained with post printing thermal treatments at different temperatures. The diodes thus fabricated work with low supply voltages, exhibit excellent mechanical stability and have a maximum operating frequency in the order of 5 MHz.
- 21 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal on Flexible Electronics
- Vol. 1 (3) , 153-158
Open AccessFully Printed and Flexible Schottky Diodes Based on Carbon Nanomaterials Operating Up to 5 MHz
The capability to fabricate printed and flexible energy harvesting and conditioning circuits, over large area and with low-cost techniques, is crucial to enable flexible and wearable electronics. Carbon nanomaterials show excellent electrical, optical, chemical, and mechanical properties for printed electronics, offering low-cost, and large-area functionality on flexible substrates. In the past few years many efforts have been dedicated to the fabrication of printed transistors made with carbon nanomaterials, but very few works have been dedicated to diodes, which are fundamental circuit elements, often employed in energy harvesting systems. Here we report a simple and cost-effective approach for the fabrication of fully inkjet printed Schottky diodes on Kapton and paper substrates using carbon nanotubes and graphene. We demonstrate that both ohmic and Schottky contacts between printed nanotubes and graphene can be obtained with post printing thermal treatments at different temperatures. The diodes thus fabricated work with low supply voltages, exhibit excellent mechanical stability and have a maximum operating frequency in the order of 5 MHz.
- Open Access
- 29 May 2021
- Published by Wiley in Advanced Electronic Materials
- Vol. 7 (7) , 2100283
1/f Noise Characterization of Bilayer MoS2 Field‐Effect Transistors on Paper with Inkjet‐Printed Contacts and hBN Dielectrics
1/f noise represents the dominant source of noise in the low‐frequency range in several physical systems, including field‐effect transistors. Its investigation can provide very important information on the fabrication process, highlighting the steps that are more prone to the introduction of defects. Here, 1/f noise in bilayer MoS2 transistors on paper with inkjet‐printed Ag contacts and hBN dielectric is investigated. These devices are promising building blocks for future low‐cost, flexible, and easily recyclable disposable electronics. The analysis of 1/f noise, performed following Hooge's empirical approach, results in a Hooge parameter ≈1–10, which is comparable to those reported for bilayer MoS2 transistors on SiO2. The present results indicate that the noise properties of the investigated devices are stable against substrate bending and are mainly determined by the printing of the dielectric, while not being sensibly affected by the use of the paper substrate. These results are promising for the further development of low noise 2D material‐based flexible electronics on paper.
- 29 May 2021
- Published by Wiley in Advanced Electronic Materials
- Vol. 7 (7) , 2100283
Open Access1/f Noise Characterization of Bilayer MoS2 Field‐Effect Transistors on Paper with Inkjet‐Printed Contacts and hBN Dielectrics
1/f noise represents the dominant source of noise in the low‐frequency range in several physical systems, including field‐effect transistors. Its investigation can provide very important information on the fabrication process, highlighting the steps that are more prone to the introduction of defects. Here, 1/f noise in bilayer MoS2 transistors on paper with inkjet‐printed Ag contacts and hBN dielectric is investigated. These devices are promising building blocks for future low‐cost, flexible, and easily recyclable disposable electronics. The analysis of 1/f noise, performed following Hooge's empirical approach, results in a Hooge parameter ≈1–10, which is comparable to those reported for bilayer MoS2 transistors on SiO2. The present results indicate that the noise properties of the investigated devices are stable against substrate bending and are mainly determined by the printing of the dielectric, while not being sensibly affected by the use of the paper substrate. These results are promising for the further development of low noise 2D material‐based flexible electronics on paper.