YLYanheng Li

Yanheng Li

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Yanheng Li has a total of 27 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    CFD simulations of electric motor end ring cooling for improved thermal management

    by Ronald O. Grover, Xiaofeng Yang, Scott Parrish, Lorenzo Nocivelli, Katherine J. Asztalos, Sibendu Som, Yanheng Li, Cooper Burns, John Van Gilder, Nitesh Attal, et al.

    Proper thermal management of an electric motor for vehicle applications extends its operating range. One cooling approach is to impinge Automatic Transmission Fluid (ATF) onto the rotor end ring. Increased ATF coverage correlates to enhanced heat transfer. Computational Fluid Dynamics (CFD) analytical tools provide a mechanism to assess motor thermal management prior to hardware fabrication. The complexity of the fluid flow (e.g., jet atomization, interface tracking, wall impingement) and heat transfer makes these simulations challenging. Computational costs are high when solving these flows on high-speed rotating meshes. Typically, a Volume-of Fluid (VOF) technique (i.e., two-fluid system) is used to resolve ATF dynamics within this rotating framework. Suitable numerical resolution of the relevant physics for thin films under strong inertial forces at high rotor speeds is computationally expensive, further increasing the run times. In this work, a numerical study of rotor-ring cooling by ATF is presented using a patent automated Cartesian cut-cell based method coupled with Automatic Mesh Refinement (AMR). This approach automatically creates the Cartesian mesh on-the-fly and can effectively handle complex rotating geometries by adaptively refining the mesh based on local gradients in the flow field which results in better resolution of the air-ATF interface. A Single non-inertial Reference Frame (SRF) approach is used to account for the rotating geometry and to further improve the overall computational efficiency. Quasi-steady state conditions are targeted in the analysis of the results. Important physics such as ATF jet structure, velocity detail near the air-jet interface, ATF coverage/accumulation on the ring surface, and cooling capacity are presented for a low-resolution Reynolds averaged Navier-Stokes (RANS), high-resolution RANS, and high-resolution Large-Eddy Simulation (LES) models. Computations are scaled over hundreds of cores on a supercomputer to maximize turnaround time. Each numerical approach is shown to capture the general trajectory of the oil jet prior to surface impingement. The high-resolution LES simulation, however, is superior in capturing small scale details and heat transfer between the free jet and surrounding air.


  • Modeling of Internal and Near-Nozzle Flow for a Gasoline Direct Injection Fuel Injector

    by Kaushik Saha, Sibendu Som, Michele Battistoni, Yanheng Li, Shaoping Quan, Peter Kelly Senecal

    A numerical study of two-phase flow inside the nozzle holes and the issuing spray jets for a multihole direct injection gasoline injector has been presented in this work. The injector geometry is representative of the Spray G nozzle, an eight-hole counterbore injector, from the engine combustion network (ECN). Simulations have been carried out for a fixed needle lift. The effects of turbulence, compressibility, and noncondensable gases have been considered in this work. Standard k–ε turbulence model has been used to model the turbulence. Homogeneous relaxation model (HRM) coupled with volume of fluid (VOF) approach has been utilized to capture the phase-change phenomena inside and outside the injector nozzle. Three different boundary conditions for the outlet domain have been imposed to examine nonflashing and evaporative, nonflashing and nonevaporative, and flashing conditions. Noticeable hole-to-hole variations have been observed in terms of mass flow rates for all the holes under all the operating conditions considered in this study. Inside the nozzle holes mild cavitationlike and in the near-nozzle region flash-boiling phenomena have been predicted when liquid fuel is subjected to superheated ambiance. Under favorable conditions, considerable flashing has been observed in the near-nozzle regions. An enormous volume is occupied by the gasoline vapor, formed by the flash boiling of superheated liquid fuel. Large outlet domain connecting the exits of the holes and the pressure outlet boundary appeared to be necessary leading to substantial computational cost. Volume-averaging instead of mass-averaging is observed to be more effective, especially for finer mesh resolutions.


  • Numerical Investigation of Two-Phase Flow Evolution of In- and Near-Nozzle Regions of a Gasoline Direct Injection Engine During Needle Transients

    by Kaushik Saha, Sibendu Som, Michele Battistoni, Yanheng Li, Eric Pomraning, P. K. Senecal

    This work involves modeling internal and near-nozzle flows of a gasoline direct injection (GDI) nozzle. The Engine Combustion Network (ECN) Spray G condition has been considered for these simulations using the nominal geometry of the Spray G injector. First, best practices for numerical simulation of the two-phase flow evolution inside and the near-nozzle regions of the Spray G injector are presented for the peak needle lift. The mass flow rate prediction for peak needle lift was in reasonable agreement with experimental data available in the ECN database. Liquid plume targeting angle and liquid penetration estimates showed promising agreement with experimental observations. The capability to assess the influence of different thermodynamic conditions on the two-phase flow nature was established by predicting non-flashing and flashing phenomena. Mild vapor formation inside the holes of the injector was predicted for flashing and non-flashing conditions, which suggests that there was sufficient depressurization of liquid fuel in a GDI nozzle. Outlet domain size and alignment of spray plumes with a grid were observed to be critically important to avoid numerical errors. Finally, to represent the real-world scenario of a moving needle in a GDI nozzle, simulations were carried out at different fixed needle lifts to provide insight to flow development inside a GDI nozzle, from opening to closing of the needle. Predictions indicated that flow patterns, and thus vapor formation characteristics, are considerably affected at very low needle lifts, for both flashing and non-flashing scenarios.


  • Open Access

    Numerical simulation of internal and near-nozzle flow of a gasoline direct injection fuel injector

    by Kaushik Saha, Sibendu Som, Michele Battistoni, Yanheng Li, Shaoping Quan, Peter Kelly Senecal


  • Modeling of Internal and Near-Nozzle Flow for a GDI Fuel Injector

    by Kaushik Saha, Sibendu Som, Michele Battistoni, Yanheng Li, S. Quan, P. K. Senecal

    A numerical study of two-phase flow inside the nozzle holes and the issuing spray jets for a multi-hole direct injection gasoline injector has been presented in this work. The injector geometry is representative of the Spray G nozzle, an eight-hole counterbore injector, from the Engine Combustion Network (ECN). Simulations have been carried out for a fixed needle lift. Effects of turbulence, compressibility and non-condensable gases have been considered in this work. Standard k–ε turbulence model has been used to model the turbulence. Homogeneous Relaxation Model (HRM) coupled with Volume of Fluid (VOF) approach has been utilized to capture the phase change phenomena inside and outside the injector nozzle. Three different boundary conditions for the outlet domain have been imposed to examine non-flashing and evaporative, non-flashing and non-evaporative and flashing conditions. Noticeable hole-to-hole variations have been observed in terms of mass flow rates for all the holes under all the operating conditions considered in this study. Inside the nozzle holes mild cavitation-like and in the near-nozzle region flash boiling phenomena have been predicted when liquid fuel is subjected to superheated ambiance. Under favorable conditions considerable flashing has been observed in the near-nozzle regions. An enormous volume is occupied by the gasoline vapor, formed by the flash boiling of superheated liquid fuel. Large outlet domain connecting the exits of the holes and the pressure outlet boundary appeared to be necessary leading to substantial computational cost. Volume-averaging instead of mass-averaging is observed to be more effective, especially for finer mesh resolutions.


  • Pebble Flow and Coolant Flow Analysis Based on a Fully Coupled Multiphysics Model

    by Yanheng Li, Wei Ji

    In pebble bed reactors (PBRs), pebble flow and coolant flow are highly correlated, and the behavior of each flow is strongly influenced by pebble-coolant interactions. Simulation of both flows in PBRs presents a multiphysics computational challenge because of the strong interplay between the flows. In this paper, a fully coupled multiphysics model is developed and applied to analyze the pebble flow and coolant flow in helium gas-cooled and fluoride salt-cooled PBR designs. A discrete element method is used to simulate the pebble motion to obtain the distribution of pebble density and velocity and the maximum contact stress on each pebble. Computational fluid dynamics is employed to simulate coolant dynamics to obtain the distribution of coolant velocity and pressure. The two methods are fully coupled through the calculation and exchange of pebble-coolant interactions at each time step. Thus, a fully coupled multiphysics computational framework is formulated. A scaled experimental fluoride salt-coo...