Dingkang Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Dingkang Wang has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
- Huikai Xie
Beijing Institute of Technology
8 shared publications - Sanjeev Jagannatha Koppal
Department of Electrical and Computer Engineering, University of Florida, Gainsville, FL, USA
6 shared publications - Karthik Dantu
University at Buffalo
2 shared publications - Lenworth Thomas
Department of Mechanical and Aerospace Engineering, University of Florida, Gainesville, FL, USA
2 shared publications - Andrew L. Sternberg
Vanderbilt University
1 shared publication Boqian Sun
School of Information and Electronics, Beijing Institute of Technology, Beijing, China
1 shared publication
Latest Publications
- Open Access
Design of an Adaptive Lightweight LiDAR to Decouple Robot-Camera Geometry
A fundamental challenge in robot perception is the coupling of the sensor pose and robot pose. This has led to research in active vision where robot pose is changed to reorient the sensor to areas of interest for perception. Further, egomotion such as jitter, and external effects such as wind and others affect perception requiring additional effort in software such as image stabilization. This effect is particularly pronounced in micro-air vehicles and micro-robots who typically are lighter and subject to larger jitter but do not have the computational capability to perform stabilization in real-time. We present a novel microelectromechanical (MEMS) mirror LiDAR system to change the field of view of the LiDAR independent of the robot motion. Our design has the potential for use on small, low-power systems where the expensive components of the LiDAR can be placed external to the small robot. We show the utility of our approach in simulation and on prototype hardware mounted on a UAV. We believe that this LiDAR and its compact movable scanning design provide mechanisms to decouple robot and sensor geometry allowing us to simplify robot perception. We also demonstrate examples of motion compensation using IMU and external odometry feedback in hardware.
Open AccessDesign of an Adaptive Lightweight LiDAR to Decouple Robot-Camera Geometry
A fundamental challenge in robot perception is the coupling of the sensor pose and robot pose. This has led to research in active vision where robot pose is changed to reorient the sensor to areas of interest for perception. Further, egomotion such as jitter, and external effects such as wind and others affect perception requiring additional effort in software such as image stabilization. This effect is particularly pronounced in micro-air vehicles and micro-robots who typically are lighter and subject to larger jitter but do not have the computational capability to perform stabilization in real-time. We present a novel microelectromechanical (MEMS) mirror LiDAR system to change the field of view of the LiDAR independent of the robot motion. Our design has the potential for use on small, low-power systems where the expensive components of the LiDAR can be placed external to the small robot. We show the utility of our approach in simulation and on prototype hardware mounted on a UAV. We believe that this LiDAR and its compact movable scanning design provide mechanisms to decouple robot and sensor geometry allowing us to simplify robot perception. We also demonstrate examples of motion compensation using IMU and external odometry feedback in hardware.
- 29 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Robotics
- Vol. 40 (15523098) , 2254-2271
Design of an Adaptive Lightweight LiDAR to Decouple Robot–Camera Geometry
A fundamental challenge in robot perception is the coupling of the sensor pose and robot pose. This has led to research in active vision where robot pose is changed to reorient the sensor to areas of interest for perception. Further, egomotion such as jitter, and external effects such as wind and others affect perception requiring additional effort in software such as image stabilization. This effect is particularly pronounced in micro-air vehicles and micro-robots who typically are lighter and subject to larger jitter but do not have the computational capability to perform stabilization in real-time. We present a novel microelectromechanical (MEMS) mirror LiDAR system to change the field of view of the LiDAR independent of the robot motion. Our design has the potential for use on small, low-power systems where the expensive components of the LiDAR can be placed external to the small robot. We show the utility of our approach in simulation and on prototype hardware mounted on a UAV. We believe that this LiDAR and its compact movable scanning design provide mechanisms to decouple robot and sensor geometry allowing us to simplify robot perception. We also demonstrate examples of motion compensation using IMU and external odometry feedback in hardware.
- 29 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Robotics
- Vol. 40 (15523098) , 2254-2271
Design of an Adaptive Lightweight LiDAR to Decouple Robot–Camera Geometry
A fundamental challenge in robot perception is the coupling of the sensor pose and robot pose. This has led to research in active vision where robot pose is changed to reorient the sensor to areas of interest for perception. Further, egomotion such as jitter, and external effects such as wind and others affect perception requiring additional effort in software such as image stabilization. This effect is particularly pronounced in micro-air vehicles and micro-robots who typically are lighter and subject to larger jitter but do not have the computational capability to perform stabilization in real-time. We present a novel microelectromechanical (MEMS) mirror LiDAR system to change the field of view of the LiDAR independent of the robot motion. Our design has the potential for use on small, low-power systems where the expensive components of the LiDAR can be placed external to the small robot. We show the utility of our approach in simulation and on prototype hardware mounted on a UAV. We believe that this LiDAR and its compact movable scanning design provide mechanisms to decouple robot and sensor geometry allowing us to simplify robot perception. We also demonstrate examples of motion compensation using IMU and external odometry feedback in hardware.
- 17 August 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Microelectromechanical Systems
- Vol. 30 (5) , 791-798
A Monolithic Forward-View Optical Scanner by a Pair of Upright MEMS Mirrors on a SiOB for LiDAR Applications
A forward-view optical scanner made of a MEMS mirror typically needs a second mirror to fold the optical beam forward, and thus an assembly structure is required, which drastically increases the overall size and weight of the scanner. This paper reports an ultra-small forward-view optical scanner with two vertically oriented micromirrors integrated on a silicon optical bench (SiOB). A new latch structure is proposed to secure the mirror frame at its vertical position and an array of meander thin-film stripes is designed to assist the latching process. The new design has been successfully fabricated and shows much-improved verticality with a maximum deviation of less than ±2° from 90°. With an optical aperture of 0.7 mm, the form factor of the MEMS chip is 4.9 mm (length) by 4.7 mm (width) by 1.8 mm (height). The measured forward field of view (FoV) of the vertical micromirrors reaches 21° in both axes at non-resonance with the voltage amplitude less than 4 V. The first resonant frequency (corresponding to the mirror frame rotation mode) of the micromirror is about 630 Hz. A fiber-pigtail bonded forward scanner is assembled with a footprint of 2 cm by 1.2 cm and a weight of 0.6 g. A forward scanning LiDAR has been built with this new MEMS scanner. The non-resonant scanning capability enables forward-view adaptive resolution and zoom-in scanning capability. [2021-0132]
- 17 August 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Microelectromechanical Systems
- Vol. 30 (5) , 791-798
A Monolithic Forward-View Optical Scanner by a Pair of Upright MEMS Mirrors on a SiOB for LiDAR Applications
A forward-view optical scanner made of a MEMS mirror typically needs a second mirror to fold the optical beam forward, and thus an assembly structure is required, which drastically increases the overall size and weight of the scanner. This paper reports an ultra-small forward-view optical scanner with two vertically oriented micromirrors integrated on a silicon optical bench (SiOB). A new latch structure is proposed to secure the mirror frame at its vertical position and an array of meander thin-film stripes is designed to assist the latching process. The new design has been successfully fabricated and shows much-improved verticality with a maximum deviation of less than ±2° from 90°. With an optical aperture of 0.7 mm, the form factor of the MEMS chip is 4.9 mm (length) by 4.7 mm (width) by 1.8 mm (height). The measured forward field of view (FoV) of the vertical micromirrors reaches 21° in both axes at non-resonance with the voltage amplitude less than 4 V. The first resonant frequency (corresponding to the mirror frame rotation mode) of the micromirror is about 630 Hz. A fiber-pigtail bonded forward scanner is assembled with a footprint of 2 cm by 1.2 cm and a weight of 0.6 g. A forward scanning LiDAR has been built with this new MEMS scanner. The non-resonant scanning capability enables forward-view adaptive resolution and zoom-in scanning capability. [2021-0132]
- 8 June 2021
- Published by Springer Nature
- p. 1932-1943
MEMS Mirror LIDAR System and Echo Signal Processing
- 8 June 2021
- Published by Springer Nature
- p. 1932-1943
MEMS Mirror LIDAR System and Echo Signal Processing
- 12 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 21 (19) , 21941-21946
A Miniature LiDAR With a Detached MEMS Scanner for Micro-Robotics
Light detection and ranging (LiDAR) has been widely used for airborne surveillance and autonomous driving. The ability of robotics or even micro-robotics can be drastically enhanced if equipped with LiDAR, but very light and small LiDAR must be used. Micro-robots have sizes close to birds or insects, and almost all existing LiDAR are too heavy and too large for them. In this work, a novel MEMS LiDAR, with its optical scanner separated from its base, is proposed and demonstrated. The scanner head will be carried by a moving micro-robot while the LiDAR base is fixed on the ground. There is a thin, flexible optical/electrical cable connecting the scanner head to the base. The scanner head consists of a MEMS mirror and a rod lens, which weighs only 10 g and measures under 4 cm long. The MEMS mirror has an aperture of 1.2 mm $\times \,\,1.4$ mm and can scan a field of view (FoV) of $9^{\circ } \times 8^{\circ }$ . As the micro-robot and the optical scanner head moves with respect to the optical receiver, an IMU (inertial measurement unit) has been embedded in the scanner head to track the motion and an algorithm has been developed to reconstruct the true point clouds. The movable head LiDAR can acquire 400 points per second and detect targets up to 35 cm away. A micro-robot can carry the scanner head while it is moving, and the point clouds can be generated at the LiDAR base. This new LiDAR configuration enables ranging, mapping, tracking, and zoom-in scanning for micro-robots.
- 12 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 21 (19) , 21941-21946
A Miniature LiDAR With a Detached MEMS Scanner for Micro-Robotics
Light detection and ranging (LiDAR) has been widely used for airborne surveillance and autonomous driving. The ability of robotics or even micro-robotics can be drastically enhanced if equipped with LiDAR, but very light and small LiDAR must be used. Micro-robots have sizes close to birds or insects, and almost all existing LiDAR are too heavy and too large for them. In this work, a novel MEMS LiDAR, with its optical scanner separated from its base, is proposed and demonstrated. The scanner head will be carried by a moving micro-robot while the LiDAR base is fixed on the ground. There is a thin, flexible optical/electrical cable connecting the scanner head to the base. The scanner head consists of a MEMS mirror and a rod lens, which weighs only 10 g and measures under 4 cm long. The MEMS mirror has an aperture of 1.2 mm $\times \,\,1.4$ mm and can scan a field of view (FoV) of $9^{\circ } \times 8^{\circ }$ . As the micro-robot and the optical scanner head moves with respect to the optical receiver, an IMU (inertial measurement unit) has been embedded in the scanner head to track the motion and an algorithm has been developed to reconstruct the true point clouds. The movable head LiDAR can acquire 400 points per second and detect targets up to 35 cm away. A micro-robot can carry the scanner head while it is moving, and the point clouds can be generated at the LiDAR base. This new LiDAR configuration enables ranging, mapping, tracking, and zoom-in scanning for micro-robots.
- Open Access
- 28 November 2020
- Published by MDPI AG in Micromachines
- Vol. 11 (12) , 1051
A Silicon Optical Bench-Based Forward-View Two-Axis Scanner for Microendoscopy Applications
Optical microendoscopy enabled by a microelectromechanical system (MEMS) scanning mirror offers great potential for in vivo diagnosis of early cancer inside the human body. However, an additional beam folding mirror is needed for a MEMS mirror to perform forward-view scanning, which drastically increases the diameter of the resultant MEMS endoscopic probe. This paper presents a new monolithic two-axis forward-view optical scanner that is composed of an electrothermally driven MEMS mirror and a beam folding mirror both vertically standing and integrated on a silicon substrate. The mirror plates of the two mirrors are parallel to each other with a small distance of 0.6 mm. The laser beam can be incident first on the MEMS mirror and then on the beam folding mirror, both at 45°. The MEMS scanner has been successfully fabricated. The measured optical scan angles of the MEMS mirror were 10.3° for the x axis and 10.2° for the y axis operated under only 3 V. The measured tip-tilt resonant frequencies of the MEMS mirror were 1590 Hz and 1850 Hz, respectively. With this compact MEMS design, a forward-view scanning endoscopic probe with an outer diameter as small as 2.5 mm can be made, which will enable such imaging probes to enter the subsegmental bronchi of an adult patient.
- 28 November 2020
- Published by MDPI AG in Micromachines
- Vol. 11 (12) , 1051
Open AccessA Silicon Optical Bench-Based Forward-View Two-Axis Scanner for Microendoscopy Applications
Optical microendoscopy enabled by a microelectromechanical system (MEMS) scanning mirror offers great potential for in vivo diagnosis of early cancer inside the human body. However, an additional beam folding mirror is needed for a MEMS mirror to perform forward-view scanning, which drastically increases the diameter of the resultant MEMS endoscopic probe. This paper presents a new monolithic two-axis forward-view optical scanner that is composed of an electrothermally driven MEMS mirror and a beam folding mirror both vertically standing and integrated on a silicon substrate. The mirror plates of the two mirrors are parallel to each other with a small distance of 0.6 mm. The laser beam can be incident first on the MEMS mirror and then on the beam folding mirror, both at 45°. The MEMS scanner has been successfully fabricated. The measured optical scan angles of the MEMS mirror were 10.3° for the x axis and 10.2° for the y axis operated under only 3 V. The measured tip-tilt resonant frequencies of the MEMS mirror were 1590 Hz and 1850 Hz, respectively. With this compact MEMS design, a forward-view scanning endoscopic probe with an outer diameter as small as 2.5 mm can be made, which will enable such imaging probes to enter the subsegmental bronchi of an adult patient.
- 2 July 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Letters
- Vol. 4 (8) , 1-4
A Low-Voltage, Low-Current, Digital-Driven MEMS Mirror for Low-Power LiDAR
Microelectromechanical (MEMS) mirrors have provided a fast and compact method to modulate light for mobile-scale projectors, LiDAR, and computational cameras. In this letter, we propose a new MEMS mirror design and its actuation method that is specifically built for low-voltage, low-current, and digital-driven IoT applications. The MEMS mirror specifically designed with direct actuation from the microcontroller was successfully fabricated and characterized. A full low-power LiDAR system based on the fabricated MEMS mirror was demonstrated, which was powered by a 9-V commercial battery.
- 2 July 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Letters
- Vol. 4 (8) , 1-4
A Low-Voltage, Low-Current, Digital-Driven MEMS Mirror for Low-Power LiDAR
Microelectromechanical (MEMS) mirrors have provided a fast and compact method to modulate light for mobile-scale projectors, LiDAR, and computational cameras. In this letter, we propose a new MEMS mirror design and its actuation method that is specifically built for low-voltage, low-current, and digital-driven IoT applications. The MEMS mirror specifically designed with direct actuation from the microcontroller was successfully fabricated and characterized. A full low-power LiDAR system based on the fabricated MEMS mirror was demonstrated, which was powered by a 9-V commercial battery.
- 24 June 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Microelectromechanical Systems
- Vol. 29 (5) , 996-1001
A Monolithic Forward-View MEMS Laser Scanner With Decoupled Raster Scanning and Enlarged Scanning Angle for Micro LiDAR Applications
This paper reports the design, fabrication, and characterization of a forward-view optical scanner realized by two vertical 2-axis MEMS mirrors integrated on a Silicon Optical Bench (SiOB). The mirror plate sizes of the first and second MEMS mirrors are 0.6×0.7 mm 2 and 1.2×1.4 mm 2 , respectively. With the second MEMS mirror larger, the optical beam will not be truncated even during large-angle dynamic scanning. This dual-mirror configuration also enables multiple scanning modes, e.g., an enlarged 2D field of view (FoV) by combining the scans of both mirrors, and a decoupled raster scanning by actuating the two mirrors separately. Experiments show that the enlarged 2D FoV reached 28°(h)×31°(v) and the FoV of the decoupled raster scanning reached 38°(h)×8°(v). The measured first resonances of the two mirrors were 2.09 kHz and 0.85 kHz, respectively. The overall size of the MEMS scanner was only 5.3 × 5.8 × 3.0 mm 3 , and its weight was 20 mg. This 2-axis forward optical scanner is much smaller and lighter than other two-mirror scanning modules, giving it a great potential for applications in miniature LiDAR for micro-robotics.
- 24 June 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Microelectromechanical Systems
- Vol. 29 (5) , 996-1001
A Monolithic Forward-View MEMS Laser Scanner With Decoupled Raster Scanning and Enlarged Scanning Angle for Micro LiDAR Applications
This paper reports the design, fabrication, and characterization of a forward-view optical scanner realized by two vertical 2-axis MEMS mirrors integrated on a Silicon Optical Bench (SiOB). The mirror plate sizes of the first and second MEMS mirrors are 0.6×0.7 mm 2 and 1.2×1.4 mm 2 , respectively. With the second MEMS mirror larger, the optical beam will not be truncated even during large-angle dynamic scanning. This dual-mirror configuration also enables multiple scanning modes, e.g., an enlarged 2D field of view (FoV) by combining the scans of both mirrors, and a decoupled raster scanning by actuating the two mirrors separately. Experiments show that the enlarged 2D FoV reached 28°(h)×31°(v) and the FoV of the decoupled raster scanning reached 38°(h)×8°(v). The measured first resonances of the two mirrors were 2.09 kHz and 0.85 kHz, respectively. The overall size of the MEMS scanner was only 5.3 × 5.8 × 3.0 mm 3 , and its weight was 20 mg. This 2-axis forward optical scanner is much smaller and lighter than other two-mirror scanning modules, giving it a great potential for applications in miniature LiDAR for micro-robotics.
- Top Cited PapersOpen Access
- 27 April 2020
- Published by MDPI AG in Micromachines
- Vol. 11 (5) , 456
MEMS Mirrors for LiDAR: A Review
In recent years, Light Detection and Ranging (LiDAR) has been drawing extensive attention both in academia and industry because of the increasing demand for autonomous vehicles. LiDAR is believed to be the crucial sensor for autonomous driving and flying, as it can provide high-density point clouds with accurate three-dimensional information. This review presents an extensive overview of Microelectronechanical Systems (MEMS) scanning mirrors specifically for applications in LiDAR systems. MEMS mirror-based laser scanners have unrivalled advantages in terms of size, speed and cost over other types of laser scanners, making them ideal for LiDAR in a wide range of applications. A figure of merit (FoM) is defined for MEMS mirrors in LiDAR scanners in terms of aperture size, field of view (FoV) and resonant frequency. Various MEMS mirrors based on different actuation mechanisms are compared using the FoM. Finally, a preliminary assessment of off-the-shelf MEMS scanned LiDAR systems is given.
- 27 April 2020
- Published by MDPI AG in Micromachines
- Vol. 11 (5) , 456
Top Cited PapersOpen AccessMEMS Mirrors for LiDAR: A Review
In recent years, Light Detection and Ranging (LiDAR) has been drawing extensive attention both in academia and industry because of the increasing demand for autonomous vehicles. LiDAR is believed to be the crucial sensor for autonomous driving and flying, as it can provide high-density point clouds with accurate three-dimensional information. This review presents an extensive overview of Microelectronechanical Systems (MEMS) scanning mirrors specifically for applications in LiDAR systems. MEMS mirror-based laser scanners have unrivalled advantages in terms of size, speed and cost over other types of laser scanners, making them ideal for LiDAR in a wide range of applications. A figure of merit (FoM) is defined for MEMS mirrors in LiDAR scanners in terms of aperture size, field of view (FoV) and resonant frequency. Various MEMS mirrors based on different actuation mechanisms are compared using the FoM. Finally, a preliminary assessment of off-the-shelf MEMS scanned LiDAR systems is given.
- 1 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 226-227
An Electrothermal Micromirror with J-shaped Bimorph Microactuators
A tip-tilt-piston micromirror with four J-shaped bimorph microactuators is developed to increase robustness and stability. The diameter of the central mirror plate is 1 mm and the footprint of the entire device is only 1.6 × 1.6 mm 2 . The micromirror scans 3° (optical) at 2.8 Vdc. The piston mode and rotation mode are measured at 880 Hz and 1555 Hz, respectively.
- 1 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 226-227
An Electrothermal Micromirror with J-shaped Bimorph Microactuators
A tip-tilt-piston micromirror with four J-shaped bimorph microactuators is developed to increase robustness and stability. The diameter of the central mirror plate is 1 mm and the footprint of the entire device is only 1.6 × 1.6 mm 2 . The micromirror scans 3° (optical) at 2.8 Vdc. The piston mode and rotation mode are measured at 880 Hz and 1555 Hz, respectively.