Gaoyou Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Gaoyou Liu has a total of 70 co-authors. Here are the top co-authors by number of shared publications:
Zhaojun Liu
Shandong University
15 shared publicationsJun Meng
12 shared publications- Xiaoming Duan
Key Laboratory of Advanced Structural-Functional Integration Materials & Green Manufacturing Technology, Harbin Institute of Technology, Harbin, China
10 shared publications - Bao-Quan Yao
National Key Laboratory of Laser Spatial Information, Harbin Institute of Technology, Harbin, China
8 shared publications Yi Chen
8 shared publicationsZhenhua Cong
7 shared publications
Latest Publications
- 15 June 2026
- Published by Optica Publishing Group in Optics Letters
- Vol. 51  (12) , 3457-3460
48 W, 5 ps, 100 kHz Ho:YLF CPA system and its application to mid-infrared ZGP OPG/OPA
In this Letter, we report a high-power, high-repetition-rate Ho:YLF chirped-pulse amplification (CPA) system driving a ZnGeP 2 (ZGP) optical parametric generator and amplifier (OPG/OPA). The Ho:YLF CPA system operates at 100 kHz, delivering 48.1 W of average power at 2050.8 nm with a compressed pulse width of 5.0 ps. Using this source to pump the ZGP OPG/OPA, we obtain a 2.7 W signal light at 3402.1 nm and 0.64 W idler light at 5160.3 nm, with a pulse width of 2.5 ps for both. Moreover, continuous wavelength tuning ranges are achieved over 3051.2–3900.2 nm for the signal light and 4205.1–5160.3 nm for the idler light.
- 15 June 2026
- Published by Optica Publishing Group in Optics Letters
- Vol. 51  (12) , 3457-3460
48 W, 5 ps, 100 kHz Ho:YLF CPA system and its application to mid-infrared ZGP OPG/OPA
In this Letter, we report a high-power, high-repetition-rate Ho:YLF chirped-pulse amplification (CPA) system driving a ZnGeP 2 (ZGP) optical parametric generator and amplifier (OPG/OPA). The Ho:YLF CPA system operates at 100 kHz, delivering 48.1 W of average power at 2050.8 nm with a compressed pulse width of 5.0 ps. Using this source to pump the ZGP OPG/OPA, we obtain a 2.7 W signal light at 3402.1 nm and 0.64 W idler light at 5160.3 nm, with a pulse width of 2.5 ps for both. Moreover, continuous wavelength tuning ranges are achieved over 3051.2–3900.2 nm for the signal light and 4205.1–5160.3 nm for the idler light.
- 1 June 2026
- Published by Optica Publishing Group in Optics Express
- Vol. 34  (12) , 21333
Efficient and controllable intracavity generation of high-energy 2 μm vortex beams and petal-like modes under annular pumping
We demonstrated a simple and effective method for continuous tuning of Laguerre–Gaussian (LG) modes in a high-energy 2.05 μm Ho:YLF laser. By translating the gain crystal along the optical axis, the spatial overlap between the pump beam and intracavity modes was controlled, enabling efficient generation of pulsed vortex beams and petal-like modes under a fixed cavity geometry. Under Q-switched operation at a repetition rate of 1 kHz, stable pulsed output of LG 0,1 was achieved with a maximum average power of 5.1 W, corresponding to a pulse energy of 5.1 mJ and a pulse duration of 83.0 ns. Experimental results showed that higher-order LG modes could be continuously tuned by adjusting the crystal position. For higher-order modes, the observed petal-like patterns corresponded to the coherent superposition of ± l degenerate states, with pulse energies at the millijoule level.
- 1 June 2026
- Published by Optica Publishing Group in Optics Express
- Vol. 34  (12) , 21333
Efficient and controllable intracavity generation of high-energy 2 μm vortex beams and petal-like modes under annular pumping
We demonstrated a simple and effective method for continuous tuning of Laguerre–Gaussian (LG) modes in a high-energy 2.05 μm Ho:YLF laser. By translating the gain crystal along the optical axis, the spatial overlap between the pump beam and intracavity modes was controlled, enabling efficient generation of pulsed vortex beams and petal-like modes under a fixed cavity geometry. Under Q-switched operation at a repetition rate of 1 kHz, stable pulsed output of LG 0,1 was achieved with a maximum average power of 5.1 W, corresponding to a pulse energy of 5.1 mJ and a pulse duration of 83.0 ns. Experimental results showed that higher-order LG modes could be continuously tuned by adjusting the crystal position. For higher-order modes, the observed petal-like patterns corresponded to the coherent superposition of ± l degenerate states, with pulse energies at the millijoule level.
- 26 May 2026
- Published by Optica Publishing Group in Optics Express
- Vol. 34  (11) , 20550-20559
3 kHz, 28.3 mJ, 65 ns, Q-switched Nd:YAG laser with Innoslab amplification
A laser diode (LD) end-pumped Nd:YAG laser system delivering clean acousto-optic Q-switched seed pulses and their efficient amplification using an Innoslab amplifier is reported. By inserting an intracavity mirror with a transmittance of 70%, Q-switched mode-locking (QML) in the long cavity acousto-optic Q-switched oscillator is effectively suppressed, enabling a stable and clean Q-switched pulse profile over the entire output range. At a pump power of 15.7 W, the seed laser delivers a single pulse energy of 0.68 mJ at a repetition rate of 3 kHz with a pulse width of 65 ns, corresponding to beam quality factors of M x 2 = 1.09 and M y 2 = 1.07. The output energy is further scaled using a double-pass Innoslab amplifier with a hybrid cavity configuration. At an absorbed pump power of 305.3 W and an injected seed energy of 0.3 mJ, a single pulse energy of 28.3 mJ is achieved. The corresponding beam quality factors M 2 are 1.23 and 1.09 in the horizontal and vertical directions, respectively, with an optical-to-optical conversion efficiency of 27.5% and a gain factor of 94.
- 26 May 2026
- Published by Optica Publishing Group in Optics Express
- Vol. 34  (11) , 20550-20559
3 kHz, 28.3 mJ, 65 ns, Q-switched Nd:YAG laser with Innoslab amplification
A laser diode (LD) end-pumped Nd:YAG laser system delivering clean acousto-optic Q-switched seed pulses and their efficient amplification using an Innoslab amplifier is reported. By inserting an intracavity mirror with a transmittance of 70%, Q-switched mode-locking (QML) in the long cavity acousto-optic Q-switched oscillator is effectively suppressed, enabling a stable and clean Q-switched pulse profile over the entire output range. At a pump power of 15.7 W, the seed laser delivers a single pulse energy of 0.68 mJ at a repetition rate of 3 kHz with a pulse width of 65 ns, corresponding to beam quality factors of M x 2 = 1.09 and M y 2 = 1.07. The output energy is further scaled using a double-pass Innoslab amplifier with a hybrid cavity configuration. At an absorbed pump power of 305.3 W and an injected seed energy of 0.3 mJ, a single pulse energy of 28.3 mJ is achieved. The corresponding beam quality factors M 2 are 1.23 and 1.09 in the horizontal and vertical directions, respectively, with an optical-to-optical conversion efficiency of 27.5% and a gain factor of 94.
- 19 March 2026
- Published by Optica Publishing Group in Optics Express
- Vol. 34  (6) , 11536
28-W, 1.49-µm, 300-Hz ring-cavity OPO with critically phase-matched KTiOAsO 4 enabled by walk-off compensation and transverse cavity-mode bias compensation via orthogonal walk-off directions
Walk-off compensation and transverse cavity-mode bias compensation are simultaneously implemented in a four-mirror ring-cavity optical parametric oscillator (OPO). Four 41.2°-cut KTiOAsO 4 (KTA) crystals are arranged into two walk-off-compensating pairs, and the two pairs are oriented in orthogonal walk-off directions, enabling effective intracavity exchange and averaging of the walk-off-induced transverse gain asymmetry. In addition, secondary energy extraction is implemented by reusing the residual pump. At 300 Hz, a 28.1-W output at 1.49 µm is obtained. With these combined measures, the spatial output characteristics of critically phase-matched OPOs affected by spatial walk-off are improved, and the parametric conversion efficiency is enhanced.
- 19 March 2026
- Published by Optica Publishing Group in Optics Express
- Vol. 34  (6) , 11536
28-W, 1.49-µm, 300-Hz ring-cavity OPO with critically phase-matched KTiOAsO 4 enabled by walk-off compensation and transverse cavity-mode bias compensation via orthogonal walk-off directions
Walk-off compensation and transverse cavity-mode bias compensation are simultaneously implemented in a four-mirror ring-cavity optical parametric oscillator (OPO). Four 41.2°-cut KTiOAsO 4 (KTA) crystals are arranged into two walk-off-compensating pairs, and the two pairs are oriented in orthogonal walk-off directions, enabling effective intracavity exchange and averaging of the walk-off-induced transverse gain asymmetry. In addition, secondary energy extraction is implemented by reusing the residual pump. At 300 Hz, a 28.1-W output at 1.49 µm is obtained. With these combined measures, the spatial output characteristics of critically phase-matched OPOs affected by spatial walk-off are improved, and the parametric conversion efficiency is enhanced.
- 6 February 2026
- Published by Optica Publishing Group in Applied Optics
- Vol. 65  (5) , 1642-1646
Non-critical phase matching KTiOAsO 4 optical parametric oscillator with a RISTRA cavity at 300 Hz
In this paper, we report a rotated image singly-resonant twisted rectangular (RISTRA) resonator implemented in a non-critical phase-matching (NCPM) KTiOAsO 4 (KTA) optical parametric oscillator (OPO). Unlike previous studies mainly focused on critically phase-matched configurations with significant spatial walk-off, this work demonstrates that the RISTRA cavity can still enhance beam quality when walk-off is negligible. The resonator introduces a 90° image rotation per round trip, which suppresses the excitation of higher order transverse modes and thus improves mode discrimination. The RISTRA cavity produces 50.3 mJ of signal and 15.5 mJ of idler energy, comparable to the planar ring cavity output of 54.0 mJ (signal) and 18.2 mJ (idler). However, the beam quality is improved: the signal M 2 is improved from 4.7×4.4 in the planar ring cavity to 2.9×2.8 in the RISTRA cavity, and the idler M 2 improves from 4.7×6.4 to 2.5×2.5. These results confirm that RISTRA remains effective for beam-quality enhancement in NCPM OPOs.
- 6 February 2026
- Published by Optica Publishing Group in Applied Optics
- Vol. 65  (5) , 1642-1646
Non-critical phase matching KTiOAsO 4 optical parametric oscillator with a RISTRA cavity at 300 Hz
In this paper, we report a rotated image singly-resonant twisted rectangular (RISTRA) resonator implemented in a non-critical phase-matching (NCPM) KTiOAsO 4 (KTA) optical parametric oscillator (OPO). Unlike previous studies mainly focused on critically phase-matched configurations with significant spatial walk-off, this work demonstrates that the RISTRA cavity can still enhance beam quality when walk-off is negligible. The resonator introduces a 90° image rotation per round trip, which suppresses the excitation of higher order transverse modes and thus improves mode discrimination. The RISTRA cavity produces 50.3 mJ of signal and 15.5 mJ of idler energy, comparable to the planar ring cavity output of 54.0 mJ (signal) and 18.2 mJ (idler). However, the beam quality is improved: the signal M 2 is improved from 4.7×4.4 in the planar ring cavity to 2.9×2.8 in the RISTRA cavity, and the idler M 2 improves from 4.7×6.4 to 2.5×2.5. These results confirm that RISTRA remains effective for beam-quality enhancement in NCPM OPOs.
- 28 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 44  (8) , 3102-3108
Optimization of Optical Parametric Oscillator Performance Through Active Temporal Pulse Shaping
Achieving simultaneously high conversion efficiency and excellent beam quality remains a central challenge in high-energy optical parametric oscillators (OPOs). Here, we demonstrate that active temporal pulse shaping of the pump provides an effective and independent control parameter for optimizing OPO performance. A high-power master-oscillator power-amplifier laser system at 1064 nm is constructed to generate programmable Gaussian and top-hat nanosecond pulses through active pre-compensation based on the inverse Frantz–Nodvik model. Both pulses preserve a near-diffraction-limited spatial quality (${\mathrm{{M}}}^{2} < 1.2$) at an average pump power of 15 W (300 Hz). Comparative experiments using a plane-parallel KTiOPO$_{4}$-OPO reveal that Gaussian pumping achieves slightly higher peak efficiency ($\sim 37 \%$) but leads to a severe beam degradation (${\mathrm{{M}}}^{2} \approx 9$), whereas top-hat pumping attains a comparable efficiency ($\sim 35 \%$) with a markedly improved beam quality (${\mathrm{{M}}}^{2} \approx 2.3$). These results confirm that the temporal pulse shaping acts as an additional and independent degree of freedom—complementary to cavity design—for optimizing OPO performance. The demonstrated approach offers a straightforward and scalable method for other wavelength regimes and nonlinear systems.
- 28 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 44  (8) , 3102-3108
Optimization of Optical Parametric Oscillator Performance Through Active Temporal Pulse Shaping
Achieving simultaneously high conversion efficiency and excellent beam quality remains a central challenge in high-energy optical parametric oscillators (OPOs). Here, we demonstrate that active temporal pulse shaping of the pump provides an effective and independent control parameter for optimizing OPO performance. A high-power master-oscillator power-amplifier laser system at 1064 nm is constructed to generate programmable Gaussian and top-hat nanosecond pulses through active pre-compensation based on the inverse Frantz–Nodvik model. Both pulses preserve a near-diffraction-limited spatial quality (${\mathrm{{M}}}^{2} < 1.2$) at an average pump power of 15 W (300 Hz). Comparative experiments using a plane-parallel KTiOPO$_{4}$-OPO reveal that Gaussian pumping achieves slightly higher peak efficiency ($\sim 37 \%$) but leads to a severe beam degradation (${\mathrm{{M}}}^{2} \approx 9$), whereas top-hat pumping attains a comparable efficiency ($\sim 35 \%$) with a markedly improved beam quality (${\mathrm{{M}}}^{2} \approx 2.3$). These results confirm that the temporal pulse shaping acts as an additional and independent degree of freedom—complementary to cavity design—for optimizing OPO performance. The demonstrated approach offers a straightforward and scalable method for other wavelength regimes and nonlinear systems.
- 12 December 2025
- Published by Optica Publishing Group in Optics Express
- Vol. 33  (25) , 53647-53656
Direct generation of cylindrical vector beams in a 2 µm mode-locked Ho-doped fiber NALM oscillator with an intra-cavity S-waveplate
We demonstrate a stable and compact 2 µm mode-locked Ho-doped fiber oscillator incorporating an intracavity S-waveplate for the direct generation of cylindrical vector beams. The oscillator employs a figure-9 nonlinear amplifying loop mirror (NALM) configuration entirely composed of polarization-maintaining fibers, ensuring environmentally robust and self-starting mode locking. The output mode-locked pulses exhibit a central wavelength of 2090.8 nm, a repetition rate of 33.8 MHz, and a spectral bandwidth of 6.1 nm. After inserting a tunable bandpass filter, a continuous wavelength tuning range from 2024 nm to 2046 nm is achieved while maintaining single-pulse operation and a polarization extinction ratio over 98%. This work presents a simple and efficient approach to generating high-purity vectorial ultrashort pulses in the 2 µm region, providing a promising platform for high-precision micro- and nanofabrication of polymers and transparent materials.
- 12 December 2025
- Published by Optica Publishing Group in Optics Express
- Vol. 33  (25) , 53647-53656
Direct generation of cylindrical vector beams in a 2 µm mode-locked Ho-doped fiber NALM oscillator with an intra-cavity S-waveplate
We demonstrate a stable and compact 2 µm mode-locked Ho-doped fiber oscillator incorporating an intracavity S-waveplate for the direct generation of cylindrical vector beams. The oscillator employs a figure-9 nonlinear amplifying loop mirror (NALM) configuration entirely composed of polarization-maintaining fibers, ensuring environmentally robust and self-starting mode locking. The output mode-locked pulses exhibit a central wavelength of 2090.8 nm, a repetition rate of 33.8 MHz, and a spectral bandwidth of 6.1 nm. After inserting a tunable bandpass filter, a continuous wavelength tuning range from 2024 nm to 2046 nm is achieved while maintaining single-pulse operation and a polarization extinction ratio over 98%. This work presents a simple and efficient approach to generating high-purity vectorial ultrashort pulses in the 2 µm region, providing a promising platform for high-precision micro- and nanofabrication of polymers and transparent materials.
- 1 December 2025
- Published by Optica Publishing Group in Optics Express
- Vol. 33  (25) , 51811-51819
Switchable Gaussian and vortex beams via spot-defect control in an Nd:YAG oscillator and subsequent KTA-OPO
Tunable laser sources capable of controlling the spatial structure of light fields are of great significance for multimodal laser physics and structured beam studies. To achieve efficient and flexible mode switching, we for the first time, to the best of our knowledge, propose and demonstrate an electro-optic Q-switching Nd:YAG laser oscillator capable of switching between Gaussian and vortex beams through spot-defect modulation. By introducing a spot-defect on the surface of a quarter-wave plate and adjusting its rotation angle, rapid switching between Gaussian and vortex beams is realized within the stable Q-switching operation region, yielding pulse energies of 4.08 mJ and 4.10 mJ for the Gaussian and vortex beams, respectively, at a repetition rate of 1 kHz. Furthermore, when employed as the pump source for a KTiOAsO 4 -based optical parametric oscillator (OPO), the system maintains consistent mode-switching behavior and excellent output performance in the mid-infrared region (∼3.5 µm).
- 1 December 2025
- Published by Optica Publishing Group in Optics Express
- Vol. 33  (25) , 51811-51819
Switchable Gaussian and vortex beams via spot-defect control in an Nd:YAG oscillator and subsequent KTA-OPO
Tunable laser sources capable of controlling the spatial structure of light fields are of great significance for multimodal laser physics and structured beam studies. To achieve efficient and flexible mode switching, we for the first time, to the best of our knowledge, propose and demonstrate an electro-optic Q-switching Nd:YAG laser oscillator capable of switching between Gaussian and vortex beams through spot-defect modulation. By introducing a spot-defect on the surface of a quarter-wave plate and adjusting its rotation angle, rapid switching between Gaussian and vortex beams is realized within the stable Q-switching operation region, yielding pulse energies of 4.08 mJ and 4.10 mJ for the Gaussian and vortex beams, respectively, at a repetition rate of 1 kHz. Furthermore, when employed as the pump source for a KTiOAsO 4 -based optical parametric oscillator (OPO), the system maintains consistent mode-switching behavior and excellent output performance in the mid-infrared region (∼3.5 µm).
- 12 November 2025
- Published by Optica Publishing Group in Optics Express
- Vol. 33  (23) , 49362-49369
OAM-controlled transfer and mid-infrared vortex generation (>4 μm) in a signal-singly resonant ZGP OPO
We demonstrated selective transfer of orbital angular momentum (OAM) to either the signal or idler in a noncollinear, signal-singly resonant ZGP optical parametric oscillator (OPO) pumped by a 2.05 μm vortex beam. By tuning the cavity length, both signal and idler vortices reached output energies above 1 mJ, whereas under collinear pumping the OAM was invariably transferred to the idler. For short cavities (50–70 mm), selective OAM transfer could also be achieved by adjusting the pump-beam tilt, enabling flexible active OAM control. Due to intrinsic instability and poor mode discrimination, the mid-infrared vortex beam quality in the plane-parallel cavity deteriorated. To overcome this, we implemented a four-mirror ring-cavity ZGP OPO, generating a ∼1 mJ first-order vortex idler at 4.45 μm with M 2 factors close to 2, an optical-to-optical conversion efficiency (OOCE) exceeding 16%, and tunability from 4.3 to 5 μm.
- 12 November 2025
- Published by Optica Publishing Group in Optics Express
- Vol. 33  (23) , 49362-49369
OAM-controlled transfer and mid-infrared vortex generation (>4 μm) in a signal-singly resonant ZGP OPO
We demonstrated selective transfer of orbital angular momentum (OAM) to either the signal or idler in a noncollinear, signal-singly resonant ZGP optical parametric oscillator (OPO) pumped by a 2.05 μm vortex beam. By tuning the cavity length, both signal and idler vortices reached output energies above 1 mJ, whereas under collinear pumping the OAM was invariably transferred to the idler. For short cavities (50–70 mm), selective OAM transfer could also be achieved by adjusting the pump-beam tilt, enabling flexible active OAM control. Due to intrinsic instability and poor mode discrimination, the mid-infrared vortex beam quality in the plane-parallel cavity deteriorated. To overcome this, we implemented a four-mirror ring-cavity ZGP OPO, generating a ∼1 mJ first-order vortex idler at 4.45 μm with M 2 factors close to 2, an optical-to-optical conversion efficiency (OOCE) exceeding 16%, and tunability from 4.3 to 5 μm.
- 15 May 2025
- Published by Optica Publishing Group in Optics Letters
- Vol. 50  (10) , 3457
Diode-pumped ring-cavity-dumped few-nanosecond single-longitudinal-mode Alexandrite laser
A red laser diode (LD) pumped single-longitudinal-mode (SLM) short-pulsed Alexandrite laser with a pulse duration of a few nanoseconds is presented, in which the cavity-dumping technique is for the first time, to our knowledge, introduced into the unidirectional ring cavity. For continuous-wave (CW) operation, a SLM Alexandrite laser with wavelength tunability from 735 nm to 786 nm was realized, and the maximum output power was 1.03 W at 759 nm. In the ring-cavity-dumped configuration, a pulsed SLM 770.6-nm Alexandrite laser was demonstrated, with a pulse energy of 12.1 µJ, a pulse duration of 7.8 ns, and a linewidth of 727 MHz at 1-kHz repetition rate. The corresponding beam quality factors were measured to be Mx2 = 1.14 and My2 = 1.09. When the repetition rate was increased to 10 kHz, the output power went up to 89 mW.
- 15 May 2025
- Published by Optica Publishing Group in Optics Letters
- Vol. 50  (10) , 3457
Diode-pumped ring-cavity-dumped few-nanosecond single-longitudinal-mode Alexandrite laser
A red laser diode (LD) pumped single-longitudinal-mode (SLM) short-pulsed Alexandrite laser with a pulse duration of a few nanoseconds is presented, in which the cavity-dumping technique is for the first time, to our knowledge, introduced into the unidirectional ring cavity. For continuous-wave (CW) operation, a SLM Alexandrite laser with wavelength tunability from 735 nm to 786 nm was realized, and the maximum output power was 1.03 W at 759 nm. In the ring-cavity-dumped configuration, a pulsed SLM 770.6-nm Alexandrite laser was demonstrated, with a pulse energy of 12.1 µJ, a pulse duration of 7.8 ns, and a linewidth of 727 MHz at 1-kHz repetition rate. The corresponding beam quality factors were measured to be Mx2 = 1.14 and My2 = 1.09. When the repetition rate was increased to 10 kHz, the output power went up to 89 mW.