Ademir Toebe
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ademir Toebe has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
- António Manuel Santos Spencer Andrade
Federal University of Santa Maria, Santa Maria, Brazil
11 shared publications - Cassiano Rech
Federal University of Santa Maria
8 shared publications - Ronaldo Antonio Guisso
Federal Technological University of Parana (UTFPR) Curitiba Paraná Brazil
5 shared publications - Tiago Miguel Klein Faistel
Graduate Program in Electrical Engineering (PPGEE), Federal University of Santa Maria, Santa Maria, Brazil
5 shared publications - Rafael Concatto Beltrame
Federal University of Santa Maria
4 shared publications - Gabriel Antonio Salvatti
Federal Universtity of Santa Maria (UFSM),Santa Maria,RS,Brazil
3 shared publications
Latest Publications
- Open Access
- 6 February 2026
- Published by Associacao Brasileira de Eletronica de Potencia SOBRAEP in Eletrônica de Potência
- Vol. 31, e202612
Modeling and Control of a Bipolar DC-DC Boost Converter for Bipolar DC Microgrids
Bipolar direct current (DC) microgrids have emerged as a promising alternative for efficiently integrating of renewable energy sources. However, these systems are susceptible to voltage imbalance between the positive and negative poles, especially with asymmetric loads. This paper presents the modeling and control of a non-isolated DC–DC Boost converter with a symmetric bipolar output suitable for photovoltaic applications. The proposed topology eliminates issues related to voltage imbalance and leakage currents while providing continuous low-ripple input current, a reduced number of components, simplified operation, and common grounding with the output neutral point. The operating principle, modeling, and control strategy of the converter are discussed, and its performance is validated through simulations and experimental results from a 1500 W prototype. The results demonstrate stable operation under both balanced and unbalanced conditions.
- 6 February 2026
- Published by Associacao Brasileira de Eletronica de Potencia SOBRAEP in Eletrônica de Potência
- Vol. 31, e202612
Open AccessModeling and Control of a Bipolar DC-DC Boost Converter for Bipolar DC Microgrids
Bipolar direct current (DC) microgrids have emerged as a promising alternative for efficiently integrating of renewable energy sources. However, these systems are susceptible to voltage imbalance between the positive and negative poles, especially with asymmetric loads. This paper presents the modeling and control of a non-isolated DC–DC Boost converter with a symmetric bipolar output suitable for photovoltaic applications. The proposed topology eliminates issues related to voltage imbalance and leakage currents while providing continuous low-ripple input current, a reduced number of components, simplified operation, and common grounding with the output neutral point. The operating principle, modeling, and control strategy of the converter are discussed, and its performance is validated through simulations and experimental results from a 1500 W prototype. The results demonstrate stable operation under both balanced and unbalanced conditions.
- Open Access
- 9 January 2026
- Published by Associacao Brasileira de Eletronica de Potencia SOBRAEP in Eletrônica de Potência
- Vol. 31, e202603
Analysis and Design of a Half-Bridge Converter with Current Doubler for Auxiliary Power Modules in Electric Vehicles
Electric vehicles (EVs) demand highly efficient power management systems to enhance reliability and extend operational autonomy. Unlike traditional internal combustion engine (ICE) vehicles, which use alternators to supply low-voltage systems, EVs rely on DC-DC converters, commonly referred to as Auxiliary Power Modules (APMs). This paper presents the analysis, design, and experimental validation of a half-bridge converter with a current-doubler (HB-CD) topology tailored for APM applications. A generalized structure is proposed to support the parallel operation of multiple modules, aiming to mitigate current stress and reduce output ripple. A 3~kW laboratory prototype was implemented using two 1.5 kW modules operating in parallel, enabling interleaved operation and effective current sharing. Experimental results demonstrate the converter’s ability to maintain high efficiency, reaching up to 94.6 % under nominal conditions and 95.9 % under minimum input voltage operation, confirming the feasibility of the proposed topology for high-current automotive applications.
- 9 January 2026
- Published by Associacao Brasileira de Eletronica de Potencia SOBRAEP in Eletrônica de Potência
- Vol. 31, e202603
Open AccessAnalysis and Design of a Half-Bridge Converter with Current Doubler for Auxiliary Power Modules in Electric Vehicles
Electric vehicles (EVs) demand highly efficient power management systems to enhance reliability and extend operational autonomy. Unlike traditional internal combustion engine (ICE) vehicles, which use alternators to supply low-voltage systems, EVs rely on DC-DC converters, commonly referred to as Auxiliary Power Modules (APMs). This paper presents the analysis, design, and experimental validation of a half-bridge converter with a current-doubler (HB-CD) topology tailored for APM applications. A generalized structure is proposed to support the parallel operation of multiple modules, aiming to mitigate current stress and reduce output ripple. A 3~kW laboratory prototype was implemented using two 1.5 kW modules operating in parallel, enabling interleaved operation and effective current sharing. Experimental results demonstrate the converter’s ability to maintain high efficiency, reaching up to 94.6 % under nominal conditions and 95.9 % under minimum input voltage operation, confirming the feasibility of the proposed topology for high-current automotive applications.
- 25 September 2025
- Published by Wiley in International Journal of Circuit Theory and Applications
- Vol. 54 (5) , 2433-2444
Transformerless DC–AC Inverter With Low Switch Count and Low Leakage Current
This paper presents a novel transformerless, common‐grounded, grid‐connected inverter for photovoltaic (PV) systems. The proposed architecture integrates a single‐switch bipolar boost converter in the direct current (DC)–DC stage and a half‐bridge inverter for the DC–alternating current (AC) conversion. The main features include the use of a single active switch in the DC–DC stage, nonpulsating input current, and grounded bipolar DC bus, which effectively mitigates common‐mode leakage current. This configuration results in a simple and low‐complexity system suitable for applications in PV systems. To validate the theoretical analysis and performance of the proposed inverter, an experimental prototype with a nominal power of 1.5 kW, input voltage of 136 , DC bus of 800 , and output voltage of 220 was developed. The experimental results confirm the expected performance, with a maximum leakage current of only 0.117 mA and peak efficiency of 96.26% operating at 750 W.
- 25 September 2025
- Published by Wiley in International Journal of Circuit Theory and Applications
- Vol. 54 (5) , 2433-2444
Transformerless DC–AC Inverter With Low Switch Count and Low Leakage Current
This paper presents a novel transformerless, common‐grounded, grid‐connected inverter for photovoltaic (PV) systems. The proposed architecture integrates a single‐switch bipolar boost converter in the direct current (DC)–DC stage and a half‐bridge inverter for the DC–alternating current (AC) conversion. The main features include the use of a single active switch in the DC–DC stage, nonpulsating input current, and grounded bipolar DC bus, which effectively mitigates common‐mode leakage current. This configuration results in a simple and low‐complexity system suitable for applications in PV systems. To validate the theoretical analysis and performance of the proposed inverter, an experimental prototype with a nominal power of 1.5 kW, input voltage of 136 , DC bus of 800 , and output voltage of 220 was developed. The experimental results confirm the expected performance, with a maximum leakage current of only 0.117 mA and peak efficiency of 96.26% operating at 750 W.
- Open Access
- 27 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. PP, 1
High Step-Up DC-DC Converter with Galvanic Isolation for Distributed Power Generation
This paper presents a new isolated DC-DC converter that integrates a coupled inductor, a transformer, and the voltage multiplier technique to achieve a high voltage gain. The proposed topology offers three degrees of freedom for voltage gain adjustment: the turns ratio of the coupled inductor (Na), the turns ratio of the transformer (Nb), and the duty cycle (D). Using these parameters, the converter can achieve the desired voltage gain with flexibility. In addition, it ensures high efficiency while minimizing voltage and current stress on the components. Theoretical evaluations of the operating principle are presented, demonstrating that some semiconductors achieve ZCS during turn-ON or turn-OFF. Modeling and closed-loop control are also evaluated, demonstrating good performance. Additionally, a comparative evaluation with similar topologies is presented. Finally, a prototype was built in the laboratory, achieving a maximum efficiency of 97.53%.
- 27 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. PP, 1
Open AccessHigh Step-Up DC-DC Converter with Galvanic Isolation for Distributed Power Generation
This paper presents a new isolated DC-DC converter that integrates a coupled inductor, a transformer, and the voltage multiplier technique to achieve a high voltage gain. The proposed topology offers three degrees of freedom for voltage gain adjustment: the turns ratio of the coupled inductor (Na), the turns ratio of the transformer (Nb), and the duty cycle (D). Using these parameters, the converter can achieve the desired voltage gain with flexibility. In addition, it ensures high efficiency while minimizing voltage and current stress on the components. Theoretical evaluations of the operating principle are presented, demonstrating that some semiconductors achieve ZCS during turn-ON or turn-OFF. Modeling and closed-loop control are also evaluated, demonstrating good performance. Additionally, a comparative evaluation with similar topologies is presented. Finally, a prototype was built in the laboratory, achieving a maximum efficiency of 97.53%.
- Open Access
- 9 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 84870-84880
Hybrid Switched Capacitor Three Winding Coupled Inductor High Step-Up DC-DC Converter
Switched capacitor cells have been studied in recent years. These approaches allow different new topologies to be generated. One such technique is the hybrid converter, where a coupled inductor and switched capacitor can be combined. Thus, in this paper, a hybrid topology is proposed that combines a three-winding coupled inductor with switched capacitor cells, with advantages such as simplicity of operation, high efficiency, low current stress, soft switching (ZCS), the possibility of reducing the capacitor value, low voltage stress on the components. To demonstrate that the converter has good performance, two prototypes were built considering different values of the duty cycle and turns ratio of coupled inductor. From there, the maximum efficiency achieves is 97.54 % at 125 W.
- 9 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 84870-84880
Open AccessHybrid Switched Capacitor Three Winding Coupled Inductor High Step-Up DC-DC Converter
Switched capacitor cells have been studied in recent years. These approaches allow different new topologies to be generated. One such technique is the hybrid converter, where a coupled inductor and switched capacitor can be combined. Thus, in this paper, a hybrid topology is proposed that combines a three-winding coupled inductor with switched capacitor cells, with advantages such as simplicity of operation, high efficiency, low current stress, soft switching (ZCS), the possibility of reducing the capacitor value, low voltage stress on the components. To demonstrate that the converter has good performance, two prototypes were built considering different values of the duty cycle and turns ratio of coupled inductor. From there, the maximum efficiency achieves is 97.54 % at 125 W.
- 14 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 39 (11) , 15269-15280
A High-Efficient Single-Switch Switched-Capacitor Partial Power Converter for On-Board Chargers
This article proposes a novel single-switch switched-capacitor (SC) series-connected partial power converter (S-PPC) for the dc–dc stage of an unidirectional on-board charger. The proposed step-down S-PPC features two key aspects: i) it performs partial power processing, reducing the active power processed by the dc–dc stage, and ii) it is transformerless, with the SC cell providing the necessary isolation to prevent a short-circuit between the low and high potentials of the electric vehicle (EV) battery pack. These characteristics allow the S-PPC to operate in a wide output voltage range with higher efficiency when compared to a conventional buck converter. To validate the analyzes, a 3 kW prototype was built and tested. It reached rated and peak efficiencies around 98.7% and 99.6%, respectively, in the constant current and constant voltage charging modes. Compared to previously published S-PPCs for EV charging applications, the SC S-PPC employs fewer semiconductors (only one active switch), which reduces its complexity and cost.
- 14 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 39 (11) , 15269-15280
A High-Efficient Single-Switch Switched-Capacitor Partial Power Converter for On-Board Chargers
This article proposes a novel single-switch switched-capacitor (SC) series-connected partial power converter (S-PPC) for the dc–dc stage of an unidirectional on-board charger. The proposed step-down S-PPC features two key aspects: i) it performs partial power processing, reducing the active power processed by the dc–dc stage, and ii) it is transformerless, with the SC cell providing the necessary isolation to prevent a short-circuit between the low and high potentials of the electric vehicle (EV) battery pack. These characteristics allow the S-PPC to operate in a wide output voltage range with higher efficiency when compared to a conventional buck converter. To validate the analyzes, a 3 kW prototype was built and tested. It reached rated and peak efficiencies around 98.7% and 99.6%, respectively, in the constant current and constant voltage charging modes. Compared to previously published S-PPCs for EV charging applications, the SC S-PPC employs fewer semiconductors (only one active switch), which reduces its complexity and cost.
- 10 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 39 (8) , 9724-9735
Capacitive Coupled Step-Down DC–DC Converter With Touch Current Limitation
This paper proposes a high-efficiency step-down dc-dc converter with limited touch current and voltage gain equivalent to the conventional buck converter. By including a capacitive coupling cell it is possible to reduce touch currents, presenting a higher safety degree against electric shocks. The main operating stages and equations describing the proposed converter are presented. The capacitive coupling cell operates through the resonant switched-capacitor principle and the impact of the parasitic elements is evaluated. Even though it has a resonant stage, the converter operates with a fixed switching frequency, simplifying the control scheme. A design guideline based on the converter specifications and safety criteria is presented. Simulation results are included to compare the touch current generated by the proposed converter and that of the conventional buck converter, demonstrating the effectiveness of the proposal. Experimental results for a 3 kW prototype operating at 180 kHz switching frequency are presented, including waveforms of main components, closed-loop control performance and efficiency curve, with a peak around 97.8%. An experimental evaluation comparing the proposed converter and the LLC half-bridge converter is also performed. Finally, the touch current tests demonstrated that the risk is automatically eliminated by the proposed converter in approximately 60 ms.
- 10 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 39 (8) , 9724-9735
Capacitive Coupled Step-Down DC–DC Converter With Touch Current Limitation
This paper proposes a high-efficiency step-down dc-dc converter with limited touch current and voltage gain equivalent to the conventional buck converter. By including a capacitive coupling cell it is possible to reduce touch currents, presenting a higher safety degree against electric shocks. The main operating stages and equations describing the proposed converter are presented. The capacitive coupling cell operates through the resonant switched-capacitor principle and the impact of the parasitic elements is evaluated. Even though it has a resonant stage, the converter operates with a fixed switching frequency, simplifying the control scheme. A design guideline based on the converter specifications and safety criteria is presented. Simulation results are included to compare the touch current generated by the proposed converter and that of the conventional buck converter, demonstrating the effectiveness of the proposal. Experimental results for a 3 kW prototype operating at 180 kHz switching frequency are presented, including waveforms of main components, closed-loop control performance and efficiency curve, with a peak around 97.8%. An experimental evaluation comparing the proposed converter and the LLC half-bridge converter is also performed. Finally, the touch current tests demonstrated that the risk is automatically eliminated by the proposed converter in approximately 60 ms.
- 26 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Control and Firmware HIL-Based Test Platform for Electric Vehicle Fast Charging Stations
The constant growth of the electromobility sector opens many opportunities for companies to expand the development of charging stations and other related devices. However, each car manufacturer has its own charging profile and distinct vehicle features. Moreover, several standards must be attended which makes the development of a generic charging station a complex task. In this regard, a test platform could accelerate and support the development stage of an electric vehicle (EV) charging station, enabling the verification of the communication requirements and control analysis. Therefore, this paper proposes a hardware-in-the-loop (HIL) based platform to test the control system and firmware of electric vehicle fast charging stations, reducing the cost and time to develop new charging stations. The power converters of the charging station are simulated in a HIL equipment, but the control system of the converters and the communication controller with the vehicle are implemented such as done in practice. Experiments using this platform are made considering the requirements of the standards related to this topic. Finally, results of the tests regarding communication protocols, security, and interoperability are presented.
- 26 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Control and Firmware HIL-Based Test Platform for Electric Vehicle Fast Charging Stations
The constant growth of the electromobility sector opens many opportunities for companies to expand the development of charging stations and other related devices. However, each car manufacturer has its own charging profile and distinct vehicle features. Moreover, several standards must be attended which makes the development of a generic charging station a complex task. In this regard, a test platform could accelerate and support the development stage of an electric vehicle (EV) charging station, enabling the verification of the communication requirements and control analysis. Therefore, this paper proposes a hardware-in-the-loop (HIL) based platform to test the control system and firmware of electric vehicle fast charging stations, reducing the cost and time to develop new charging stations. The power converters of the charging station are simulated in a HIL equipment, but the control system of the converters and the communication controller with the vehicle are implemented such as done in practice. Experiments using this platform are made considering the requirements of the standards related to this topic. Finally, results of the tests regarding communication protocols, security, and interoperability are presented.
- 20 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38 (12) , 15045-15054
Five-Level Switched-Capacitor Unidirectional Rectifier With Reduced Number of Components
This paper proposes a three-phase five-level switched-capacitor unidirectional rectifier. The proposed unidirectional rectifier is derived from a bidirectional five-level active neutral point clamped topology by eliminating four active switches per phase. Even with fewer active switches, five voltage levels can still be synthesized at the input ac-side, which leads to reduction of the size and weight of the grid interface filter. Moreover, the proposed unidirectional rectifier enables the self-voltage regulation of floating capacitors, reducing the complexity of the control system, and also allows the generation of smaller output dc voltages in comparison to conventional boost-type rectifiers. The circuit derivation of the proposed rectifier, as well as its features, operating principles and control scheme are described in this paper. Finally, experimental results for a three-phase 3 kW prototype are presented to demonstrate the feasibility of the proposed structure.
- 20 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38 (12) , 15045-15054
Five-Level Switched-Capacitor Unidirectional Rectifier With Reduced Number of Components
This paper proposes a three-phase five-level switched-capacitor unidirectional rectifier. The proposed unidirectional rectifier is derived from a bidirectional five-level active neutral point clamped topology by eliminating four active switches per phase. Even with fewer active switches, five voltage levels can still be synthesized at the input ac-side, which leads to reduction of the size and weight of the grid interface filter. Moreover, the proposed unidirectional rectifier enables the self-voltage regulation of floating capacitors, reducing the complexity of the control system, and also allows the generation of smaller output dc voltages in comparison to conventional boost-type rectifiers. The circuit derivation of the proposed rectifier, as well as its features, operating principles and control scheme are described in this paper. Finally, experimental results for a three-phase 3 kW prototype are presented to demonstrate the feasibility of the proposed structure.