Andrey Pavlyshko
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Andrey Pavlyshko has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Ihor Sydorenko
Odesa Polytechnic National University
2 shared publications - Kateryna Kirkopulo
Odesа Polytechnic National University
2 shared publications - Liubov Bovnegra
Odesa Polytechnic National University
2 shared publications - Victor Kurgan
Odesa Polytechnic National University
2 shared publications - Vladyslav Vaysman
Odessa Polytechnic State University
2 shared publications - A. Matveev1 shared publication
Latest Publications
- 31 August 2023
- Published by Springer Nature
- p. 432-439
Experimental Study of Longevity in the Metallic Structure of Boom for a Portal Crane of Seaport
- 31 August 2023
- Published by Springer Nature
- p. 432-439
Experimental Study of Longevity in the Metallic Structure of Boom for a Portal Crane of Seaport
- 9 September 2022
- Published by Springer Nature
- p. 455-464
Stabilization of Natural Frequency Oscillation Equipment When Changing Its Weight
- 9 September 2022
- Published by Springer Nature
- p. 455-464
Stabilization of Natural Frequency Oscillation Equipment When Changing Its Weight
- Open Access
- 2 March 2022
- Published by National Technical University Kharkiv Polytechnic Institute in Cutting & Tools in Technological System
- No. 96,p. 138-145
THE EFFECT OF ELASTIC RECOIL OF CLOSED-TYPE LIFTING ROPES AFTER THEIR MANUFACTURE AND DRAWING
A study was made of stresses and factors of internal forces in the elements of ropes of a closed structure during their manufacture. It is established that when twisting a rope of closed construction, its shaped wires suffer from bending deformation, twisting and stretching. In this case, the shaped wires are subjected to a complex load with the concomitant rotation of the axes of the stress tensor. The stresses in the elastic cross-sectional area of the rope wire are considered and its limit is determined for shaped cross-sections and for asymmetric shaped cross-sections. Formulas for approximate determination of tangential and normal stresses in the elements of a closed rope of non-circular profile are obtained: (wedge-shaped, zeta-shaped and x-shaped).
- 2 March 2022
- Published by National Technical University Kharkiv Polytechnic Institute in Cutting & Tools in Technological System
- No. 96,p. 138-145
Open AccessTHE EFFECT OF ELASTIC RECOIL OF CLOSED-TYPE LIFTING ROPES AFTER THEIR MANUFACTURE AND DRAWING
A study was made of stresses and factors of internal forces in the elements of ropes of a closed structure during their manufacture. It is established that when twisting a rope of closed construction, its shaped wires suffer from bending deformation, twisting and stretching. In this case, the shaped wires are subjected to a complex load with the concomitant rotation of the axes of the stress tensor. The stresses in the elastic cross-sectional area of the rope wire are considered and its limit is determined for shaped cross-sections and for asymmetric shaped cross-sections. Formulas for approximate determination of tangential and normal stresses in the elements of a closed rope of non-circular profile are obtained: (wedge-shaped, zeta-shaped and x-shaped).
- Open Access
- 26 December 2021
- Published by National Technical University Kharkiv Polytechnic Institute in Cutting & Tools in Technological System
- No. 95,p. 45-56
IMPROVING GRINDING OF GEAR WHEELS APPLIED IN GEARBOXES OF POWER ENGINEERING
Development of modem power engineering follows the line of continuous increase in speed, coefficient of corrosive action and capacity of units. Gears and reducers are responsible parts of modem machinery and occupy an important place in the domestic power engineering construction. Durability and wear resistance of gears, apart from the design factors, also depends on the technological methods of treatment. The final stage of production of such wheels is the operation of gear grinding. In the process of gear grinding in a thin surface ball there are complex thermomechanical processes. As a result of short-time heating to high temperatures, structural transformations, burns, and in some cases even micro- and macro-thicknesses occur in such a surface bail. In addition, there are cases of making tooth wheels with adjacent defects grinding (for example, the appearance of the surface of the ball teeth of large tensioning forces), which reduces the life of the work, and in some cases causes a breakdown of the teeth in operating conditions. Development of effective measures to ensure the quality of the surface of the ball on the operation of grinding baggage in part depends on the possibility of predicting (or calculation) of temperatures and residual loads on the depth of the cemented teeth ball. The method of calculation of internal surplus Toads occurring during grinding of wheels with cemented steels is suggested. On the basis of the performed calculations and experiments the ways to improve the quality of production of working surfaces of gears, which are used in the wits of thermal and nuclear power plants are suggested and grounded.
- 26 December 2021
- Published by National Technical University Kharkiv Polytechnic Institute in Cutting & Tools in Technological System
- No. 95,p. 45-56
Open AccessIMPROVING GRINDING OF GEAR WHEELS APPLIED IN GEARBOXES OF POWER ENGINEERING
Development of modem power engineering follows the line of continuous increase in speed, coefficient of corrosive action and capacity of units. Gears and reducers are responsible parts of modem machinery and occupy an important place in the domestic power engineering construction. Durability and wear resistance of gears, apart from the design factors, also depends on the technological methods of treatment. The final stage of production of such wheels is the operation of gear grinding. In the process of gear grinding in a thin surface ball there are complex thermomechanical processes. As a result of short-time heating to high temperatures, structural transformations, burns, and in some cases even micro- and macro-thicknesses occur in such a surface bail. In addition, there are cases of making tooth wheels with adjacent defects grinding (for example, the appearance of the surface of the ball teeth of large tensioning forces), which reduces the life of the work, and in some cases causes a breakdown of the teeth in operating conditions. Development of effective measures to ensure the quality of the surface of the ball on the operation of grinding baggage in part depends on the possibility of predicting (or calculation) of temperatures and residual loads on the depth of the cemented teeth ball. The method of calculation of internal surplus Toads occurring during grinding of wheels with cemented steels is suggested. On the basis of the performed calculations and experiments the ways to improve the quality of production of working surfaces of gears, which are used in the wits of thermal and nuclear power plants are suggested and grounded.
- Open Access
- 1 January 2018
- Published by Odessa Polytechnic National University in Odes’kyi Politechnichnyi Universytet. Pratsi
- Vol. 1 (54) , 51-61
COMPUTER MODELING OF IMPLANT FOR FEMUR REINFORCEMENT
- 1 January 2018
- Published by Odessa Polytechnic National University in Odes’kyi Politechnichnyi Universytet. Pratsi
- Vol. 1 (54) , 51-61
Open AccessCOMPUTER MODELING OF IMPLANT FOR FEMUR REINFORCEMENT