Sandip Ghosh Chowdhury
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Sandip Ghosh Chowdhury has a total of 56 co-authors. Here are the top co-authors by number of shared publications:
V. Rajinikanth
Academy of Scientific and Innovative Research (AcSIR), Ghaziabad, India
4 shared publicationsChiradeep Ghosh
Research and Development Division, Tata Steel Limited, Jamshedpur, India
3 shared publicationsG. K. Bansal
Materials Engineering Division, CSIR-National Metallurgical Laboratory, Jamshedpur, India
3 shared publicationsV. C. Srivastava
Academy of Scientific and Innovative Research (AcSIR), Ghaziabad, India
3 shared publicationsB. Mahato
CSIR National Metallurgical Laboratory
2 shared publications- Gopi Kishor Mandal
CSIR-National Metallurgical Laboratory
2 shared publications
Latest Publications
- 8 January 2026
- Published by Wiley in Steel Research International
Microstructure and Mechanical Properties of Quenched and Nonisothermally Partitioned Low‐Alloy Steels
The current study examines the microstructure and mechanical properties of two low‐alloy steels processed through quenching and nonisothermal partitioning (Q&NP) treatment. Toward this, continuous cooling and Q&NP treatments are initially performed in a dilatometer to understand the phase transformations. The Q&NP experiments reveal an additional transformation in dilatation curves during the initial stages of nonisothermal partitioning, which corresponds to bainite/fresh martensite, followed by fresh martensite up to the end of the partitioning process. In addition, Q&NP treatments are performed on large size samples in muffle and salt bath furnaces to evaluate tensile and Charpy impact toughness properties. The dilatometer samples do not show retained austenite at any of the quench temperature (QT), whereas retained austenite is observed in the larger size samples, which might be due to the formation of bainite during initial quenching to the QT in the salt bath. Despite the formation of bainite, QT dependent retained austenite fraction in large Q&NP samples follows the trend calculated by the optimum QT models. The Q&NP treated samples exhibit increased tensile elongation (≈85% for steel 1 and 400% for steel 2) and Charpy impact toughness (≈390% for steel 1 and ≈250% for steel 2) compared to water quenched samples.
- 8 January 2026
- Published by Wiley in Steel Research International
Microstructure and Mechanical Properties of Quenched and Nonisothermally Partitioned Low‐Alloy Steels
The current study examines the microstructure and mechanical properties of two low‐alloy steels processed through quenching and nonisothermal partitioning (Q&NP) treatment. Toward this, continuous cooling and Q&NP treatments are initially performed in a dilatometer to understand the phase transformations. The Q&NP experiments reveal an additional transformation in dilatation curves during the initial stages of nonisothermal partitioning, which corresponds to bainite/fresh martensite, followed by fresh martensite up to the end of the partitioning process. In addition, Q&NP treatments are performed on large size samples in muffle and salt bath furnaces to evaluate tensile and Charpy impact toughness properties. The dilatometer samples do not show retained austenite at any of the quench temperature (QT), whereas retained austenite is observed in the larger size samples, which might be due to the formation of bainite during initial quenching to the QT in the salt bath. Despite the formation of bainite, QT dependent retained austenite fraction in large Q&NP samples follows the trend calculated by the optimum QT models. The Q&NP treated samples exhibit increased tensile elongation (≈85% for steel 1 and 400% for steel 2) and Charpy impact toughness (≈390% for steel 1 and ≈250% for steel 2) compared to water quenched samples.
- 3 June 2024
- Published by Springer Nature in JOM
- Vol. 76 (8) , 4458-4470
A Quantitative Approach to Precipitate Characterization in Wire Arc Additive Manufactured Inconel 600 Series Alloys
- 3 June 2024
- Published by Springer Nature in JOM
- Vol. 76 (8) , 4458-4470
A Quantitative Approach to Precipitate Characterization in Wire Arc Additive Manufactured Inconel 600 Series Alloys
- 7 March 2022
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 53 (5) , 1806-1820
On the Competitive Substitutional Partitioning During Nano-pearlitic Transformation in Multicomponent Steels
- 7 March 2022
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 53 (5) , 1806-1820
On the Competitive Substitutional Partitioning During Nano-pearlitic Transformation in Multicomponent Steels
- Open Access
- 17 May 2021
- Published by Defence Scientific Information and Documentation Centre in Defence Science Journal
- Vol. 71 (03) , 383-389
Phase transformation, Mechanical Properties and Corrosion Behavior of 304L Austenitic Stainless Steel Rolled at Room and Cryo Temperatures
The present work investigates the effect of rolling (90% thickness reduction) on phase transformation, mechanical properties, and corrosion behaviour of 304L-austenitic stainless steel through cryorolling and room temperature rolling. The processed steel sheets were characterised through X-ray diffraction (XRD), electron backscattered diffraction (EBSD), and vibrating sample magnetometer (VSM). The analysis of XRD patterns, EBSD scan, and vibrating sample magnetometer results confirmed the transformation of the austenitic phase to the martensitic phase during rolling. Cryorolling resulted in improved tensile strength and microhardness of 1808 MPa and 538 VHN, respectively, as compared to 1566 MPa and 504 VHN for room temperature rolling. The enhancement in properties of cryorolled steel is attributed to its higher dislocation density compared to room temperature rolled steel. The corrosion behaviour was assessed via linear polarisation corrosion tests. Corrosion resistance was found to decrease with increasing rolling reduction in both room temperature rolled and cryorolled specimens.
- 17 May 2021
- Published by Defence Scientific Information and Documentation Centre in Defence Science Journal
- Vol. 71 (03) , 383-389
Open AccessPhase transformation, Mechanical Properties and Corrosion Behavior of 304L Austenitic Stainless Steel Rolled at Room and Cryo Temperatures
The present work investigates the effect of rolling (90% thickness reduction) on phase transformation, mechanical properties, and corrosion behaviour of 304L-austenitic stainless steel through cryorolling and room temperature rolling. The processed steel sheets were characterised through X-ray diffraction (XRD), electron backscattered diffraction (EBSD), and vibrating sample magnetometer (VSM). The analysis of XRD patterns, EBSD scan, and vibrating sample magnetometer results confirmed the transformation of the austenitic phase to the martensitic phase during rolling. Cryorolling resulted in improved tensile strength and microhardness of 1808 MPa and 538 VHN, respectively, as compared to 1566 MPa and 504 VHN for room temperature rolling. The enhancement in properties of cryorolled steel is attributed to its higher dislocation density compared to room temperature rolled steel. The corrosion behaviour was assessed via linear polarisation corrosion tests. Corrosion resistance was found to decrease with increasing rolling reduction in both room temperature rolled and cryorolled specimens.
- 21 April 2021
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 74 (5) , 1253-1260
Effect of Finish Rolling Temperature on Microstructure and Mechanical Properties of Low-Si Steel After Quenching and Nonisothermal Partitioning
- 21 April 2021
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 74 (5) , 1253-1260
Effect of Finish Rolling Temperature on Microstructure and Mechanical Properties of Low-Si Steel After Quenching and Nonisothermal Partitioning
- 13 August 2020
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 51 (10) , 5088-5100
Quench Temperature-Dependent Mechanical Properties During Nonisothermal Partitioning
- 13 August 2020
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 51 (10) , 5088-5100
Quench Temperature-Dependent Mechanical Properties During Nonisothermal Partitioning
- 4 May 2020
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 51 (7) , 3410-3424
Quench Temperature-Dependent Phase Transformations During Nonisothermal Partitioning
- 4 May 2020
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 51 (7) , 3410-3424
Quench Temperature-Dependent Phase Transformations During Nonisothermal Partitioning
- 17 May 2018
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 49 (8) , 3501-3514
Microstructure–Property Correlation in Low-Si Steel Processed Through Quenching and Nonisothermal Partitioning
- 17 May 2018
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 49 (8) , 3501-3514
Microstructure–Property Correlation in Low-Si Steel Processed Through Quenching and Nonisothermal Partitioning
- 27 July 2017
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 48 (10) , 4842-4856
Correlation of Microstructure and Texture in a Two-Phase High-Mn Twinning-Induced Plasticity Steel During Cold Rolling
- 27 July 2017
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 48 (10) , 4842-4856
Correlation of Microstructure and Texture in a Two-Phase High-Mn Twinning-Induced Plasticity Steel During Cold Rolling