Miodrag Zukovic
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Miodrag Zukovic has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
- Livija Cveticanin
Faculty of Technical Sciences, University of Novi Sad, Novi Sad, Serbia
21 shared publications - Ivana Kovacic
Faculty of Technical Sciences, Centre of Excellence for Vibro-Acoustic Systems and Signal Processing CEVAS, University of Novi Sad, Novi Sad, Serbia
20 shared publications L. Cveticanin
9 shared publicationsD. Cveticanin
6 shared publications- Matthew Phillip Cartmell
University of Strathclyde
6 shared publications - Dragi Radomirovic
University of Novi Sad
4 shared publications
Latest Publications
- Open Access
- 6 November 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (21) , 10999
Static and Nonlinear Dynamic Response of a Polymer Liner Confined by a Rigid Overwrap in a Type IV Hydrogen Pressure Vessel
The mechanical response of a polymeric liner in a Type IV hydrogen pressure vessel is governed by internal gas pressure, liner stiffness, nonlinear deformation, and confinement by the composite overwrap. A reduced-order analytical model is developed to describe the static and nonlinear dynamic behavior of the liner using a single generalized radial displacement. The formulation assumes cylindrical liner geometry, isothermal gas behavior, approximately constant gas mass over the mechanical response time scale, and negligible damping. The model incorporates deformation-dependent gas pressure, nonlinear restoring characteristics, effective fluid inertia, and finite clearance between the liner and overwrap. Analytical conditions for equilibrium, stability, and saddle-node bifurcation are derived. For the linear restoring model, a first integral characterizes finite-amplitude oscillations and the conditions for contact with the overwrap. Fluid inertia affects finite-amplitude motion but not static equilibrium or infinitesimal oscillations. The analysis further shows that finite-amplitude oscillations induced by an initial velocity can produce both contraction and expansion of the liner, with the diameter becoming smaller or larger than its initial value D0. Application to a representative PA11 liner demonstrates the strong effect of overwrap confinement, which substantially reduces the radial deformation. The results distinguish static and dynamic contact conditions and provide a compact analytical framework for assessing deformation, stability, and nonlinear dynamic behavior of Type IV hydrogen vessel liners.
- 6 November 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (21) , 10999
Open AccessStatic and Nonlinear Dynamic Response of a Polymer Liner Confined by a Rigid Overwrap in a Type IV Hydrogen Pressure Vessel
The mechanical response of a polymeric liner in a Type IV hydrogen pressure vessel is governed by internal gas pressure, liner stiffness, nonlinear deformation, and confinement by the composite overwrap. A reduced-order analytical model is developed to describe the static and nonlinear dynamic behavior of the liner using a single generalized radial displacement. The formulation assumes cylindrical liner geometry, isothermal gas behavior, approximately constant gas mass over the mechanical response time scale, and negligible damping. The model incorporates deformation-dependent gas pressure, nonlinear restoring characteristics, effective fluid inertia, and finite clearance between the liner and overwrap. Analytical conditions for equilibrium, stability, and saddle-node bifurcation are derived. For the linear restoring model, a first integral characterizes finite-amplitude oscillations and the conditions for contact with the overwrap. Fluid inertia affects finite-amplitude motion but not static equilibrium or infinitesimal oscillations. The analysis further shows that finite-amplitude oscillations induced by an initial velocity can produce both contraction and expansion of the liner, with the diameter becoming smaller or larger than its initial value D0. Application to a representative PA11 liner demonstrates the strong effect of overwrap confinement, which substantially reduces the radial deformation. The results distinguish static and dynamic contact conditions and provide a compact analytical framework for assessing deformation, stability, and nonlinear dynamic behavior of Type IV hydrogen vessel liners.
- Open Access
- 24 April 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (9) , 4170
Nonlinear Vibrations of Filled Re-Entrant Hexagonal Units: Coupled Geometric–Inertial Effects
This work solves the problem associated with the lack of analytical models capable of describing the nonlinear vibration behavior of re-entrant hexagonal units when geometric nonlinearity and structural modifications, such as soft filling, are taken into account. The purpose of this study is to develop an analytical framework that enables prediction and control of vibration characteristics, with particular emphasis on achieving low-frequency response and enhanced energy storage and redistribution within the structure. The proposed approach is based on Lagrangian modeling of the unit cell, leading to a nonlinear equation of motion of the Liénard type that admits a first integral. By exploiting the existence of this integral, an approximate analytical expression for the oscillation period is derived using energy-based methods. The analysis is performed for two configurations: an empty unit and a unit filled with a soft material, allowing direct comparison of their dynamic responses. The analytical results are validated through comparison with numerical simulations and available experimental data. A parametric study is conducted to evaluate the influence of the mass ratio and the re-entrant angle on the oscillation period and frequency. Furthermore, the effects of filling mass, stiffness, and degree of filling are systematically investigated, revealing distinct inertia-dominated and stiffness-dominated regimes. The obtained results provide clear design guidelines for tailoring the dynamic response of re-entrant hexagonal units. It is shown that low-frequency vibration and increased capacity for energy storage can be achieved through appropriate selection of geometric parameters and filling properties, with potential applications in vibration control and structural design.
- 24 April 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (9) , 4170
Open AccessNonlinear Vibrations of Filled Re-Entrant Hexagonal Units: Coupled Geometric–Inertial Effects
This work solves the problem associated with the lack of analytical models capable of describing the nonlinear vibration behavior of re-entrant hexagonal units when geometric nonlinearity and structural modifications, such as soft filling, are taken into account. The purpose of this study is to develop an analytical framework that enables prediction and control of vibration characteristics, with particular emphasis on achieving low-frequency response and enhanced energy storage and redistribution within the structure. The proposed approach is based on Lagrangian modeling of the unit cell, leading to a nonlinear equation of motion of the Liénard type that admits a first integral. By exploiting the existence of this integral, an approximate analytical expression for the oscillation period is derived using energy-based methods. The analysis is performed for two configurations: an empty unit and a unit filled with a soft material, allowing direct comparison of their dynamic responses. The analytical results are validated through comparison with numerical simulations and available experimental data. A parametric study is conducted to evaluate the influence of the mass ratio and the re-entrant angle on the oscillation period and frequency. Furthermore, the effects of filling mass, stiffness, and degree of filling are systematically investigated, revealing distinct inertia-dominated and stiffness-dominated regimes. The obtained results provide clear design guidelines for tailoring the dynamic response of re-entrant hexagonal units. It is shown that low-frequency vibration and increased capacity for energy storage can be achieved through appropriate selection of geometric parameters and filling properties, with potential applications in vibration control and structural design.
- 16 November 2025
- Published by Springer Nature
- p. 45-58
Truly Nonlinear Oscillator with Position-Dependent Mass: Theory and Application
- 16 November 2025
- Published by Springer Nature
- p. 45-58
Truly Nonlinear Oscillator with Position-Dependent Mass: Theory and Application
- Open Access
- 12 March 2025
- Published by MDPI AG in Mathematics
- Vol. 13 (6) , 937
Vibration of the Liénard Oscillator with Quadratic Damping and Constant Excitation
In this paper, the Liénard oscillator with nonlinear deflection, quadratic damping, and constant excitation is considered. In general, there is no analytic solution for the Liénard equation. However, for certain parameter values, the exact analytic solution exists and has the form of the Ateb function. In addition, for the oscillator with weakly perturbed parameters, the approximate analytic solution is obtained. For the considered Liénard equation, independently of parameter values, the first integral is found. The main advantage of the first integral is that after simple analysis and without solving the equation of motion, it gives important data about oscillation: the dependence of vibration on initial conditions and on the variation of the constant of excitation. In addition, by integration of the first integral, the period of vibration follows. The results of the research on the Liénard equation are applied for optimization of the properties of a sieve in the process industry. For the sieve with mass variation, dependent on the displacement function, the influence of excitation force on the system vibration is analyzed, and the optimal value is suggested.
- 12 March 2025
- Published by MDPI AG in Mathematics
- Vol. 13 (6) , 937
Open AccessVibration of the Liénard Oscillator with Quadratic Damping and Constant Excitation
In this paper, the Liénard oscillator with nonlinear deflection, quadratic damping, and constant excitation is considered. In general, there is no analytic solution for the Liénard equation. However, for certain parameter values, the exact analytic solution exists and has the form of the Ateb function. In addition, for the oscillator with weakly perturbed parameters, the approximate analytic solution is obtained. For the considered Liénard equation, independently of parameter values, the first integral is found. The main advantage of the first integral is that after simple analysis and without solving the equation of motion, it gives important data about oscillation: the dependence of vibration on initial conditions and on the variation of the constant of excitation. In addition, by integration of the first integral, the period of vibration follows. The results of the research on the Liénard equation are applied for optimization of the properties of a sieve in the process industry. For the sieve with mass variation, dependent on the displacement function, the influence of excitation force on the system vibration is analyzed, and the optimal value is suggested.
- Open Access
- 28 September 2024
- Published by MDPI AG in Mathematics
- Vol. 12 (19) , 3040
Approximate Analytic Frequency of Strong Nonlinear Oscillator
In this paper, a new analytic expression for the frequency of vibration of a strong nonlinear polynomial-type oscillator is introduced. The method for frequency calculation is based on the transformation of the nonlinear oscillators into linear ones using the equality of their amplitudes and periods of vibration. The frequency of the linear oscillator is assumed to be the sum of frequencies corresponding to each nonlinearity in the original oscillator separately, i.e., the sum of frequencies of truly nonlinear oscillators. The obtained frequency is a complex function of amplitude, coefficient and order of nonlinearity. For simplification, the frequencies of the truly nonlinear oscillators are modified as power order functions of the exact frequency of the cubic oscillator which is linearly dependent on the amplitude of vibration. In this paper, the approximate frequency expression is developed for the harmonic any-order nonlinear oscillator and oscillators with the sum of polynomial nonlinearities. The accuracy of the obtained frequencies is tested on the examples of non-integer order nonlinear oscillators and also on a quadratic-cubic oscillator. The difference between the analytical and exact, numerically obtained results is negligible. The suggested approximate frequency expression has a simple algebraic form and is suitable for application by engineers and technicians.
- 28 September 2024
- Published by MDPI AG in Mathematics
- Vol. 12 (19) , 3040
Open AccessApproximate Analytic Frequency of Strong Nonlinear Oscillator
In this paper, a new analytic expression for the frequency of vibration of a strong nonlinear polynomial-type oscillator is introduced. The method for frequency calculation is based on the transformation of the nonlinear oscillators into linear ones using the equality of their amplitudes and periods of vibration. The frequency of the linear oscillator is assumed to be the sum of frequencies corresponding to each nonlinearity in the original oscillator separately, i.e., the sum of frequencies of truly nonlinear oscillators. The obtained frequency is a complex function of amplitude, coefficient and order of nonlinearity. For simplification, the frequencies of the truly nonlinear oscillators are modified as power order functions of the exact frequency of the cubic oscillator which is linearly dependent on the amplitude of vibration. In this paper, the approximate frequency expression is developed for the harmonic any-order nonlinear oscillator and oscillators with the sum of polynomial nonlinearities. The accuracy of the obtained frequencies is tested on the examples of non-integer order nonlinear oscillators and also on a quadratic-cubic oscillator. The difference between the analytical and exact, numerically obtained results is negligible. The suggested approximate frequency expression has a simple algebraic form and is suitable for application by engineers and technicians.
- Open Access
- 18 September 2023
- Published by MDPI AG in Mathematics
- Vol. 11 (18) , 3958
Oscillator with Time-Variable Degree of Nonlinearity: Theory and Application in Aging of Polymer Composite Structure
In this paper, a new type of one-degree-of-freedom pure nonlinear oscillator with a time variable degree of nonlinearity is introduced. Namely, the degree of the nonlinearity in the restitution force is not a constant but a ‘slow time’ variable function. The mathematical model is a second-order nonlinear differential equation with time-variable parameters. An approximate solving procedure based on the method of time-variable amplitude, frequency and phase is developed. It is found that the vibration properties depend on initial conditions and the degree of time-variable function. The theoretical results are tested on almost linear, cubic and high-degree nonlinear oscillators. According to theoretical considerations, the process of aging in fiber-reinforced polymer composite structure is investigated. It is found that the amplitude and the frequency of vibration of the reinforced polymer structure decrease over time. The result is in good agreement with already published experimental data. The additional conclusion of the research is that the oscillator model suggested in the paper is suitable for the prediction of mechanic properties of the polymer structure in aging and also in similar destructive processes.
- 18 September 2023
- Published by MDPI AG in Mathematics
- Vol. 11 (18) , 3958
Open AccessOscillator with Time-Variable Degree of Nonlinearity: Theory and Application in Aging of Polymer Composite Structure
In this paper, a new type of one-degree-of-freedom pure nonlinear oscillator with a time variable degree of nonlinearity is introduced. Namely, the degree of the nonlinearity in the restitution force is not a constant but a ‘slow time’ variable function. The mathematical model is a second-order nonlinear differential equation with time-variable parameters. An approximate solving procedure based on the method of time-variable amplitude, frequency and phase is developed. It is found that the vibration properties depend on initial conditions and the degree of time-variable function. The theoretical results are tested on almost linear, cubic and high-degree nonlinear oscillators. According to theoretical considerations, the process of aging in fiber-reinforced polymer composite structure is investigated. It is found that the amplitude and the frequency of vibration of the reinforced polymer structure decrease over time. The result is in good agreement with already published experimental data. The additional conclusion of the research is that the oscillator model suggested in the paper is suitable for the prediction of mechanic properties of the polymer structure in aging and also in similar destructive processes.
- 22 November 2021
- Published by Springer Nature in Nonlinear Dynamics
- Vol. 107 (1) , 1411
Correction to: Vibro-impact system with non-ideal excitation: analytical investigations
- 22 November 2021
- Published by Springer Nature in Nonlinear Dynamics
- Vol. 107 (1) , 1411
Correction to: Vibro-impact system with non-ideal excitation: analytical investigations
- 13 September 2021
- Published by Springer Nature in Nonlinear Dynamics
- Vol. 106 (1) , 105-123
Vibro-impact system with non-ideal excitation: analytical investigations
- 13 September 2021
- Published by Springer Nature in Nonlinear Dynamics
- Vol. 106 (1) , 105-123
Vibro-impact system with non-ideal excitation: analytical investigations
- 4 January 2021
- Published by Springer Nature in Meccanica
- Vol. 56 (2) , 439-460
On the dynamics of vibro-impact systems with ideal and non-ideal excitation
- 4 January 2021
- Published by Springer Nature in Meccanica
- Vol. 56 (2) , 439-460
On the dynamics of vibro-impact systems with ideal and non-ideal excitation
- Open Access
- 1 January 2021
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1730 (1) , 012014
Numerical analysis of a vibro-impact system with ideal and non-ideal excitation
This study is concerned with modelling and analyses of a vibro-impact system consisting of a crank-slider mechanism and one oscillator attached to it, where the system can be exposed to ideal or non-ideal excitation. The impact occurs during the motion of the oscillator when it hits a base, and the excitation of the driving source is affected by this behaviour. The aim is to determine the interaction between a driving torque and the motion of the oscillator. To achieve this aim in a methodologically sound manner, both vibro-impact systems with ideal and non-ideal excitation are analysed. For these system differential equations are formed and the impact model is provided in the paper. The impact causes a strong nonlinearity in the system. The mathematical model of the vibro-impact system with ideal excitation is presented as a second order differential equation where the vibro-impact system with non-ideal excitation is given as a coupled system of nonlinear second order differential equations. Numerical simulations are carried out for the two systems and the results obtained are shown in terms of frequency response diagrams as well as in terms of time-displacement diagrams. The results found for different systems are compared mutually, and the differences between them are pointed out. Impact solutions for different regions of the excitation frequency are shown. For a specific value of the excitation frequency in the frequency response diagram where multiple solutions are found, basin of attractor diagrams are formed. Average value of the excitation frequency is used for the vibro-impact system with non-ideal excitation.
- 1 January 2021
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1730 (1) , 012014
Open AccessNumerical analysis of a vibro-impact system with ideal and non-ideal excitation
This study is concerned with modelling and analyses of a vibro-impact system consisting of a crank-slider mechanism and one oscillator attached to it, where the system can be exposed to ideal or non-ideal excitation. The impact occurs during the motion of the oscillator when it hits a base, and the excitation of the driving source is affected by this behaviour. The aim is to determine the interaction between a driving torque and the motion of the oscillator. To achieve this aim in a methodologically sound manner, both vibro-impact systems with ideal and non-ideal excitation are analysed. For these system differential equations are formed and the impact model is provided in the paper. The impact causes a strong nonlinearity in the system. The mathematical model of the vibro-impact system with ideal excitation is presented as a second order differential equation where the vibro-impact system with non-ideal excitation is given as a coupled system of nonlinear second order differential equations. Numerical simulations are carried out for the two systems and the results obtained are shown in terms of frequency response diagrams as well as in terms of time-displacement diagrams. The results found for different systems are compared mutually, and the differences between them are pointed out. Impact solutions for different regions of the excitation frequency are shown. For a specific value of the excitation frequency in the frequency response diagram where multiple solutions are found, basin of attractor diagrams are formed. Average value of the excitation frequency is used for the vibro-impact system with non-ideal excitation.