Saeede Ghorbanpour
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Saeede Ghorbanpour has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
Brandon A. McWilliams
5 shared publicationsMarko Knezevic
5 shared publicationsJonathan Bicknell
4 shared publications- Marko Knezevic
Department of Mechanical Engineering, University of New Hampshire, Durham, NH 03824, USA
4 shared publications Nicholas C. Ferreri
3 shared publicationsAnil Kumar
2 shared publications
Latest Publications
- Top Cited Papers
- 1 February 2020
- Published by Elsevier in International Journal of Plasticity
- Vol. 125, 63-79
Experimental characterization and crystal plasticity modeling of anisotropy, tension-compression asymmetry, and texture evolution of additively manufactured Inconel 718 at room and elevated temperatures
- 1 February 2020
- Published by Elsevier in International Journal of Plasticity
- Vol. 125, 63-79
Top Cited PapersExperimental characterization and crystal plasticity modeling of anisotropy, tension-compression asymmetry, and texture evolution of additively manufactured Inconel 718 at room and elevated temperatures
- 3 March 2019
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 42 (6) , 1357-1372
Low‐cycle fatigue behavior of rolled WE43‐T5 magnesium alloy
This paper describes the main results from an investigation into the strength and low‐cycle fatigue (LCF) behavior of a rolled plate of WE43 Mg alloy in its T5 condition at room temperature. The alloy was found to exhibit small tension/compression yield asymmetry and small anisotropy being stronger in transverse direction (TD) than in rolling direction (RD) along with some anisotropy in strain hardening. The LCF tests were conducted under strain‐controlled conditions with the strain amplitudes ranging from 0.6% to 1.4% without the mean strain component. While the stress amplitudes during the LCF were higher for tests along TD than RD, the LCF life was similar for both directions. As revealed by electron microscopy, the fractured surfaces under tension consisted mainly of microvoid coalescence with some transgranular facets, while those fractured in LCF showed a combination of intergranular fracture and transgranular facets with minor content of microvoid coalescence.
- 3 March 2019
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 42 (6) , 1357-1372
Low‐cycle fatigue behavior of rolled WE43‐T5 magnesium alloy
This paper describes the main results from an investigation into the strength and low‐cycle fatigue (LCF) behavior of a rolled plate of WE43 Mg alloy in its T5 condition at room temperature. The alloy was found to exhibit small tension/compression yield asymmetry and small anisotropy being stronger in transverse direction (TD) than in rolling direction (RD) along with some anisotropy in strain hardening. The LCF tests were conducted under strain‐controlled conditions with the strain amplitudes ranging from 0.6% to 1.4% without the mean strain component. While the stress amplitudes during the LCF were higher for tests along TD than RD, the LCF life was similar for both directions. As revealed by electron microscopy, the fractured surfaces under tension consisted mainly of microvoid coalescence with some transgranular facets, while those fractured in LCF showed a combination of intergranular fracture and transgranular facets with minor content of microvoid coalescence.
- Top Cited Papers
- 1 March 2019
- Published by Elsevier in Materials Characterization
- Vol. 149, 184-197
Role of grain structure, grain boundaries, crystallographic texture, precipitates, and porosity on fatigue behavior of Inconel 718 at room and elevated temperatures
- 1 March 2019
- Published by Elsevier in Materials Characterization
- Vol. 149, 184-197
Top Cited PapersRole of grain structure, grain boundaries, crystallographic texture, precipitates, and porosity on fatigue behavior of Inconel 718 at room and elevated temperatures
- 14 February 2019
- Published by Springer Nature
- p. 219-225
Effect of Hot Working on the High Cycle Fatigue Behavior of WE43 Rare Earth Magnesium Alloy
- 14 February 2019
- Published by Springer Nature
- p. 219-225
Effect of Hot Working on the High Cycle Fatigue Behavior of WE43 Rare Earth Magnesium Alloy
- 1 February 2019
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 747, 27-41
Effect of hot working and aging heat treatments on monotonic, cyclic, and fatigue behavior of WE43 magnesium alloy
- 1 February 2019
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 747, 27-41
Effect of hot working and aging heat treatments on monotonic, cyclic, and fatigue behavior of WE43 magnesium alloy
- 30 September 2016
- Published by Springer Nature in Journal of Central South University
- Vol. 23 (9) , 2146-2155
Application of artificial neural network to predict Vickers microhardness of AA6061 friction stir welded sheets
- 30 September 2016
- Published by Springer Nature in Journal of Central South University
- Vol. 23 (9) , 2146-2155
Application of artificial neural network to predict Vickers microhardness of AA6061 friction stir welded sheets