Botao Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Botao Zhang has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
Shengjie Gong
6 shared publicationsZhenqin Xiong
5 shared publicationsShichang Dong
4 shared publicationsWeimin Ma
4 shared publicationsYidan Yuan
2 shared publicationsYong Mei
Shanghai Jiao Tong Univ, Sch Nucl Sci & Engn, Shanghai, Peoples R China
2 shared publications
Latest Publications
- 25 August 2025
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 255
Subcooled pool boiling induced vibration and bubble behaviors for a vertical heated surface
- 25 August 2025
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 255
Subcooled pool boiling induced vibration and bubble behaviors for a vertical heated surface
- 9 July 2024
- Published by Elsevier in Applied Thermal Engineering
- Vol. 254
Numerical simulation for pressure fluctuations caused by the growth of a single boiling bubble
- 9 July 2024
- Published by Elsevier in Applied Thermal Engineering
- Vol. 254
Numerical simulation for pressure fluctuations caused by the growth of a single boiling bubble
- 6 February 2024
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 223
Experimental study on boiling induced vibration excited by a single bubble
- 6 February 2024
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 223
Experimental study on boiling induced vibration excited by a single bubble
- 1 November 2021
- Published by Elsevier in Progress in Nuclear Energy
- Vol. 141
Vortex shedding induced vibration of thin strip in confined rectangular channel
- 1 November 2021
- Published by Elsevier in Progress in Nuclear Energy
- Vol. 141
Vortex shedding induced vibration of thin strip in confined rectangular channel
- 1 April 2019
- Published by Elsevier in Experimental Thermal and Fluid Science
- Vol. 102, 368-375
Experimental study on 3D bubble shape evolution in swirl flow
- 1 April 2019
- Published by Elsevier in Experimental Thermal and Fluid Science
- Vol. 102, 368-375
Experimental study on 3D bubble shape evolution in swirl flow
- 2 July 2017
- Published by ASME International
Effects of Heater Material and Surface Orientation on Heat Transfer Coefficient and Critical Heat Flux of Nucleate Boiling
External reactor vessel cooling (ERVC) is the key technology for In-Vessel Retention (IVR) to ensure the safety of a nuclear power plant (NPP) under severe accident conditions. The thermal margin of nucleate boiling heat transfer on the reactor pressure vessel (RPV) lower head is important for ERVC and of wide concern to researchers. In such boiling heat transfer processes, the reactor vessel wall inclination effect on the heat transfer coefficient (HTC) and critical heat flux (CHF) should be considered. In this study, experiments were performed to investigate the effects of heater material and surface orientation on the HTC and CHF of nucleate boiling. Copper and stainless steel (SS) surfaces were used to perform boiling tests under atmosphere pressure. The orientation angle of both boiling surfaces were varied between 0° (upward) and 180° (downward). The experimental results show that the surface orientation effects on the HTC is slight for both the copper surface and the SS surface. In addition, the relationship of measured CHF values with the inclination angles was obtained and it shows that the CHF value changes little as the inclination angle increases from 0° to 120° but it decreases rapidly as the orientation angle increases towards 180° for both boiling surfaces. The material effect on CHF is also observed and the copper surface has higher CHF value than the SS surface. Based on the experimental data, a correlation for CHF prediction is developed which includes both the surface orientation effect and the heater material effect.
- 2 July 2017
- Published by ASME International
Effects of Heater Material and Surface Orientation on Heat Transfer Coefficient and Critical Heat Flux of Nucleate Boiling
External reactor vessel cooling (ERVC) is the key technology for In-Vessel Retention (IVR) to ensure the safety of a nuclear power plant (NPP) under severe accident conditions. The thermal margin of nucleate boiling heat transfer on the reactor pressure vessel (RPV) lower head is important for ERVC and of wide concern to researchers. In such boiling heat transfer processes, the reactor vessel wall inclination effect on the heat transfer coefficient (HTC) and critical heat flux (CHF) should be considered. In this study, experiments were performed to investigate the effects of heater material and surface orientation on the HTC and CHF of nucleate boiling. Copper and stainless steel (SS) surfaces were used to perform boiling tests under atmosphere pressure. The orientation angle of both boiling surfaces were varied between 0° (upward) and 180° (downward). The experimental results show that the surface orientation effects on the HTC is slight for both the copper surface and the SS surface. In addition, the relationship of measured CHF values with the inclination angles was obtained and it shows that the CHF value changes little as the inclination angle increases from 0° to 120° but it decreases rapidly as the orientation angle increases towards 180° for both boiling surfaces. The material effect on CHF is also observed and the copper surface has higher CHF value than the SS surface. Based on the experimental data, a correlation for CHF prediction is developed which includes both the surface orientation effect and the heater material effect.