Viktor V. Gabov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Viktor V. Gabov has a total of 34 co-authors. Here are the top co-authors by number of shared publications:
- Denis A. Zadkov
St. Petersburg Mining University
15 shared publications - Nguyen Khac Linh
Saint-Petersburg Mining University, 2, 21 Line of Vasilyevsky Island, Saint-Petersburg, 199106, Russian
7 shared publications A. V. Stebnev
2 shared publications- Nguyen Van Xuan
Instituteof Energy and Mining Mechanical Engineering - Vinacomin
2 shared publications - Tran Duc Tho
Institute of Energy and Mining Mechanical Engineering
2 shared publications - V. V. Buevich2 shared publications
Latest Publications
- Open Access
- 1 January 2022
- Published by Saint-Petersburg Mining University in Journal of Mining Institute
- Vol. 257, 764-770
Increasing the content of coarse fractions in the mined coal mass by a combine using paired cuts
The main volume of coal is mined underground using shearers. In modern shearers, auger actuators are mainly used, which are distinguished by the simplicity of design, manufacturability and reliability. However, in the process of separating coal from mass by cutting, the yield of fine grades is 40-50 % of the total production volume. Therefore, the search and development of technical solutions that provide an increase in the yield of large fractions in the process of coal mining with auger shearers is an urgent task. Traditionally, this problem is solved by increasing the thickness of the slices, which is achieved by installing cutters with a larger radial reach and increasing the shearer feed rate. An unconventional way to increase the cross section of slices by forming energy-efficient paired and group slices with mutual superposition of stress fields in the mass from the action of neighboring cutters is considered. The results of modeling the process of cutting coal confirm that an increase in the efficiency of destruction of the rock mass by the cutters of the auger executive bodies of the shearer can be achieved by a complex technical solution, including the formation of paired cuts and combined stress zones in the rock mass. As a result, the output of large fragments when cutting with paired cutters increases by 1.3-1.8 times compared with cutting with a single cutter.
- 1 January 2022
- Published by Saint-Petersburg Mining University in Journal of Mining Institute
- Vol. 257, 764-770
Open AccessIncreasing the content of coarse fractions in the mined coal mass by a combine using paired cuts
The main volume of coal is mined underground using shearers. In modern shearers, auger actuators are mainly used, which are distinguished by the simplicity of design, manufacturability and reliability. However, in the process of separating coal from mass by cutting, the yield of fine grades is 40-50 % of the total production volume. Therefore, the search and development of technical solutions that provide an increase in the yield of large fractions in the process of coal mining with auger shearers is an urgent task. Traditionally, this problem is solved by increasing the thickness of the slices, which is achieved by installing cutters with a larger radial reach and increasing the shearer feed rate. An unconventional way to increase the cross section of slices by forming energy-efficient paired and group slices with mutual superposition of stress fields in the mass from the action of neighboring cutters is considered. The results of modeling the process of cutting coal confirm that an increase in the efficiency of destruction of the rock mass by the cutters of the auger executive bodies of the shearer can be achieved by a complex technical solution, including the formation of paired cuts and combined stress zones in the rock mass. As a result, the output of large fragments when cutting with paired cutters increases by 1.3-1.8 times compared with cutting with a single cutter.
- 1 January 2022
- Published by LLC Gornaya Kniga in Mining informational and analytical bulletin
- No. 6-2,p. 205-222
To the problem of improvement the working tools of mining excavation machines
- 1 January 2022
- Published by LLC Gornaya Kniga in Mining informational and analytical bulletin
- No. 6-2,p. 205-222
To the problem of improvement the working tools of mining excavation machines
- 1 January 2022
- Published by LLC Gornaya Kniga in Mining informational and analytical bulletin
- No. 6,p. 46-61
Adaptable and energy-efficient powered roof support unit
- 1 January 2022
- Published by LLC Gornaya Kniga in Mining informational and analytical bulletin
- No. 6,p. 46-61
Adaptable and energy-efficient powered roof support unit
- 1 January 2022
- Published by LLC Gornaya Kniga in Mining informational and analytical bulletin
- No. 1,p. 5-19
Justification of engineering solutions on reduction of occupational traumatism in coal longwalls
- 1 January 2022
- Published by LLC Gornaya Kniga in Mining informational and analytical bulletin
- No. 1,p. 5-19
Justification of engineering solutions on reduction of occupational traumatism in coal longwalls
- Open Access
- 1 July 2021
- Published by International Digital Organization for Scientific Information (IDOSI) in International Journal of Engineering
- Vol. 34 (7) , 1804-1809
Evaluating the Efficiency of Coal Loading Process by Simulating the Process of Loading onto the Face Conveyor with a Shearer with an Additional Share
This paper analyses the possibility of increasing the efficiency of loading the destroyed rock mass into the face scraper conveyor by the lagging screw actuator of the shearer in the process of coal mining in the complex mechanized treatment faces of coal mines. It was taken into account that the most significant influence on the loading efficiency of coal is exerted by the dimensions of the cross-sectional area of the loading window, the distance between the screw and conveyor and the height of the bottom of the conveyor. Non-traditional technical solutions are proposed that reduce the negative impact of the gap between the screw and the conveyor on the efficiency of coal loading by the lagging screw actuator of shearers and increase the degree of filling of the conveyor groove. Technical solutions contribute to the formation of a rational section of the cargo flow in the trough of the downhole conveyor and, therefore, increase its productivity. The results of modeling the process of loading coal onto the face conveyor by an auger actuator with an additional loading device are presented. Evaluation of the effectiveness of the proposed constructive technical solutions for the interface unit in the loading area confirmed an increase of 2.94 times the maximum capacity of the screw executive body for loading coal onto the face conveyor while 2.7 times less specific energy consumption during loading.
- 1 July 2021
- Published by International Digital Organization for Scientific Information (IDOSI) in International Journal of Engineering
- Vol. 34 (7) , 1804-1809
Open AccessEvaluating the Efficiency of Coal Loading Process by Simulating the Process of Loading onto the Face Conveyor with a Shearer with an Additional Share
This paper analyses the possibility of increasing the efficiency of loading the destroyed rock mass into the face scraper conveyor by the lagging screw actuator of the shearer in the process of coal mining in the complex mechanized treatment faces of coal mines. It was taken into account that the most significant influence on the loading efficiency of coal is exerted by the dimensions of the cross-sectional area of the loading window, the distance between the screw and conveyor and the height of the bottom of the conveyor. Non-traditional technical solutions are proposed that reduce the negative impact of the gap between the screw and the conveyor on the efficiency of coal loading by the lagging screw actuator of shearers and increase the degree of filling of the conveyor groove. Technical solutions contribute to the formation of a rational section of the cargo flow in the trough of the downhole conveyor and, therefore, increase its productivity. The results of modeling the process of loading coal onto the face conveyor by an auger actuator with an additional loading device are presented. Evaluation of the effectiveness of the proposed constructive technical solutions for the interface unit in the loading area confirmed an increase of 2.94 times the maximum capacity of the screw executive body for loading coal onto the face conveyor while 2.7 times less specific energy consumption during loading.
- 1 January 2020
- Published by LLC Gornaya Kniga in Mining informational and analytical bulletin
- No. S4
Scheme for the installation of cutters on screw executive bodies with cutting, coupling and group cuts
Очистные комбайны со шнековыми исполнительными органами получили преобладающее применение при подземной добыче угля в комплексно - механизированных очистных забоях из пластов средний и большой мощности. Шнековые исполнительные органы отличаются технологичностью, надежностью и производительностью. Однако процессу отделения ими угля от массива свойственно существенно значимое переизмельчение добываемого угля, пылеобразование и высокая энергоемкость добычи. Рассмотрена возможность повышения эффективности отделения угля от массива совершенствованием схем расстановки резцов шнековых исполнительных органов. Повышение эффективности процесса резания, при существующих конструктивных ограничениях радиального вылета резцов и толщины срезов, достигается использованием комбинированных последовательно-групповых схем расстановки резцов. В качестве групповых схем рассматриваются энергоэффективные подрезные, парные и групповые срезы с большей площадью сечений срезов по сравнению с одиночными срезами и, следовательно, с большей крупностью отделяемых фрагментов угля, снижением удельного расхода энергии и выхода...
- 1 January 2020
- Published by LLC Gornaya Kniga in Mining informational and analytical bulletin
- No. S4
Scheme for the installation of cutters on screw executive bodies with cutting, coupling and group cuts
Очистные комбайны со шнековыми исполнительными органами получили преобладающее применение при подземной добыче угля в комплексно - механизированных очистных забоях из пластов средний и большой мощности. Шнековые исполнительные органы отличаются технологичностью, надежностью и производительностью. Однако процессу отделения ими угля от массива свойственно существенно значимое переизмельчение добываемого угля, пылеобразование и высокая энергоемкость добычи. Рассмотрена возможность повышения эффективности отделения угля от массива совершенствованием схем расстановки резцов шнековых исполнительных органов. Повышение эффективности процесса резания, при существующих конструктивных ограничениях радиального вылета резцов и толщины срезов, достигается использованием комбинированных последовательно-групповых схем расстановки резцов. В качестве групповых схем рассматриваются энергоэффективные подрезные, парные и групповые срезы с большей площадью сечений срезов по сравнению с одиночными срезами и, следовательно, с большей крупностью отделяемых фрагментов угля, снижением удельного расхода энергии и выхода...
- Open Access
- 25 April 2019
- Published by Saint-Petersburg Mining University in Journal of Mining Institute
- Vol. 236 (2) , 153-161
FEATURES OF ELEMENTARY BURST FORMATION DURING CUTTING COALS AND ISOTROPIC MATERIALS WITH REFERENCE CUTTING TOOL OF MINING MACHINES
ОСОБЕННОСТИ ФОРМИРОВАНИЯ ЭЛЕМЕНТАРНЫХ СКОЛОВ В ПРОЦЕССЕ РЕЗАНИЯ УГЛЕЙ И ИЗОТРОПНЫХ МАТЕРИАЛОВ ЭТАЛОННЫМ РЕЗЦОМ ГОРНЫХ МАШИН
- 25 April 2019
- Published by Saint-Petersburg Mining University in Journal of Mining Institute
- Vol. 236 (2) , 153-161
Open AccessFEATURES OF ELEMENTARY BURST FORMATION DURING CUTTING COALS AND ISOTROPIC MATERIALS WITH REFERENCE CUTTING TOOL OF MINING MACHINES
ОСОБЕННОСТИ ФОРМИРОВАНИЯ ЭЛЕМЕНТАРНЫХ СКОЛОВ В ПРОЦЕССЕ РЕЗАНИЯ УГЛЕЙ И ИЗОТРОПНЫХ МАТЕРИАЛОВ ЭТАЛОННЫМ РЕЗЦОМ ГОРНЫХ МАШИН
- 1 January 2019
- Published by Ore and Metals Publishing House in Eurasian Mining
- No. 1,p. 37-39
IMPROVING EFFICIENCY OF CLEANUP AND COAL FLOW FORMATION ON CONVEYOR BY SHEARER LOADER WITH ACCESSORIAL BLADE
- 1 January 2019
- Published by Ore and Metals Publishing House in Eurasian Mining
- No. 1,p. 37-39
IMPROVING EFFICIENCY OF CLEANUP AND COAL FLOW FORMATION ON CONVEYOR BY SHEARER LOADER WITH ACCESSORIAL BLADE
- 17 December 2018
- Published by Ore and Metals Publishing House in Eurasian Mining
- No. 2,p. 22-25
Improvement of drum shearer coal loading performance
The article discusses improvement of broken coal loading on armored face conveyor by tailgate drum of a shearer in the course of fully mechanized coal mining. The scope of the analysis covers coal flow in the zone of coal–pick interaction, axial displacement between vanes, passive removal from the drum to the conveyor as well as coal flow formation on the conveyor. The features and constraints of coal flow in each zone are discussed. It is shown that the highest influence on the coal loading efficiency is exerted by the drum and conveyor spacing, discharge window size and the face side height of the conveyor. The discharge window coefficient is introduced. It is pointed at the required reduction in the coal flow resistance by increasing the cross-section area of the discharge window and the volume of coal loading zone on the conveyor. The discharge window cross-section area is increased by implementing the proposed integrated engineering solutions, in particular, conical drum web, ranging arm frame structure and decreased depth of cross-section of the supporting beam. The accepted new design enables increasing maximum loading capacity of the shearer tailgate drum, decreasing dust formation and coal fineness in the process of coal removal from cutting zone and loading on conveyor, as well as reducing energy consumption.
- 17 December 2018
- Published by Ore and Metals Publishing House in Eurasian Mining
- No. 2,p. 22-25
Improvement of drum shearer coal loading performance
The article discusses improvement of broken coal loading on armored face conveyor by tailgate drum of a shearer in the course of fully mechanized coal mining. The scope of the analysis covers coal flow in the zone of coal–pick interaction, axial displacement between vanes, passive removal from the drum to the conveyor as well as coal flow formation on the conveyor. The features and constraints of coal flow in each zone are discussed. It is shown that the highest influence on the coal loading efficiency is exerted by the drum and conveyor spacing, discharge window size and the face side height of the conveyor. The discharge window coefficient is introduced. It is pointed at the required reduction in the coal flow resistance by increasing the cross-section area of the discharge window and the volume of coal loading zone on the conveyor. The discharge window cross-section area is increased by implementing the proposed integrated engineering solutions, in particular, conical drum web, ranging arm frame structure and decreased depth of cross-section of the supporting beam. The accepted new design enables increasing maximum loading capacity of the shearer tailgate drum, decreasing dust formation and coal fineness in the process of coal removal from cutting zone and loading on conveyor, as well as reducing energy consumption.
- Open Access
- 15 November 2018
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 194 (4) , 042019
Substantiation of parameters of coal unloading process onto conveyor using shearer drums
In this article the process of coal unloading from the face's fracture zone to the conveyor using shearer drums is presented. The effect of the form and dimensions of the sectional area of the loading window and the height of the conveyor's edge surface in the working zone of the rear shearer drum on filling with coal of the auger's intervane space and the effect on circulation of the broken-down coal are analyzed. Estimations and directions of further studies of the coal unloading process from the fracture zone to the face conveyor are proposed.
- 15 November 2018
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 194 (4) , 042019
Open AccessSubstantiation of parameters of coal unloading process onto conveyor using shearer drums
In this article the process of coal unloading from the face's fracture zone to the conveyor using shearer drums is presented. The effect of the form and dimensions of the sectional area of the loading window and the height of the conveyor's edge surface in the working zone of the rear shearer drum on filling with coal of the auger's intervane space and the effect on circulation of the broken-down coal are analyzed. Estimations and directions of further studies of the coal unloading process from the fracture zone to the face conveyor are proposed.