Eri Widianto
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Eri Widianto has a total of 179 co-authors. Here are the top co-authors by number of shared publications:
- Iman Santoso
Department of Physics, Faculty of Mathematics and Natural Sciences, Universitas Gadjah Mada, Yogyakarta, Indonesia
24 shared publications - Kuwat Triyana
Department of Physics, Faculty of Mathematics and Natural Sciences, Universitas Gadjah Mada, Yogyakarta, Indonesia
11 shared publications Muhammad Riswan
10 shared publicationsKardiman
9 shared publicationsShobih
8 shared publicationsIman Santoso
7 shared publications
Latest Publications
- 28 August 2026
- Published by Elsevier in Ceramics International
- Vol. 52 (27) , 52239-52251
Annealing-induced crystallographic evolution of hydroxyapatite derived from sea urchin shell waste: A Williamson–Hall analysis
- 28 August 2026
- Published by Elsevier in Ceramics International
- Vol. 52 (27) , 52239-52251
Annealing-induced crystallographic evolution of hydroxyapatite derived from sea urchin shell waste: A Williamson–Hall analysis
- 25 August 2026
- Published by Elsevier in Materials Today Physics
- Vol. 67
Defect-activated oxygen transport mediates the breakdown of graphene-protected copper
- 25 August 2026
- Published by Elsevier in Materials Today Physics
- Vol. 67
Defect-activated oxygen transport mediates the breakdown of graphene-protected copper
- Open Access
- 24 July 2026
- Published by Elsevier in SSRN Electronic Journal
Effect of Formamidinium and Methylammonium Iodide Surface Passivation on the Structure, Optical Properties, and Photo-stability of Open-Air MAPbI 3 Perovskite Films
The effect of post-deposition surface passivation with formamidinium iodide (FAI) and methylammonium iodide (MAI) on the structure, surface chemistry, optical properties, and photo-stability of methylammonium lead iodide (MAPbI3) perovskite films processed entirely in open air (60–70% relative humidity) was investigated. Films were spin-coated on C-TiO2/MP-TiO2/ITO substrates and analysed in the same configuration used for graphite-electrode devices. X-ray diffraction confirmed tetragonal MAPbI3 (a ≈ 8.88Å, c ≈ 12.57Å) with Scherrer (110) crystallite sizes of 25.2, 26.9, and 25.1nm for the control, MAI, and FAI films, essentially unchanged across the series (dislocation density ∼1.4–1.6×1015 m−2). Scanning electron microscopy revealed mean surface grain sizes of 125, 128, and 128nm (with a broader distribution after MAI treatment) and film thicknesses of 1050, 1329, and 1064nm. Fourier-transform infrared spectroscopy showed a new ν(C=N) band at 1712 cm−1 unique to FAI and a high-frequency C–H shift to 2823 cm−1 for MAI, evidencing distinct, cation-specific surface chemical interactions, while Raman confirmed a methylammonium-libration mode emerging only after MAI treatment. Diffuse-reflectance Tauc analysis (directallowed, baseline-corrected) gave optical band gaps of 1.58, 1.55, and 1.66 eV for MAPbI3, MAPbI3+MAI, and MAPbI3+FAI, all consistent with tetragonal MAPbI3 (∼1.55–1.61 eV); rather than a bulk-gap shift, the optical signature of passivation appears as a 13nm red-shift of the photoluminescence maximum from the control to the FAI-treated film, indicating modified surface/near-surface recombination. To link these film-level changes to functional behaviour, the films were tested in a graphite electrode stack under a white-LED bench (Pin ≈ 6.1mW, 17 330 lx, A = 0.9 cm2, ≈0.07 sun, not AM1.5G); the relative response improved by ∼2.1× (MAI) and ∼3.6× (FAI) over the control, and a 16.7-h continuous-illumination stress test (100 successive J–V sweeps) showed a positive light-soaking response for both passivated films (light-soaking factor LSF = 1.75 for MAI and 1.85 for FAI; sweep-to-sweep variability ≤ 2.4%) against a flat, noisier control (LSF = 0.99, 5.2% variability). Overall, a direct same-batch comparison shows that FAI and MAI surface passivation induce distinct surface chemistries that improve the structural quality, optical signature, and operational photo-stability of open-air MAPbI3 films, providing a materials-level basis for selecting passivation chemistry in low-cost, humid-ambient fabrication.
- 24 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessEffect of Formamidinium and Methylammonium Iodide Surface Passivation on the Structure, Optical Properties, and Photo-stability of Open-Air MAPbI 3 Perovskite Films
The effect of post-deposition surface passivation with formamidinium iodide (FAI) and methylammonium iodide (MAI) on the structure, surface chemistry, optical properties, and photo-stability of methylammonium lead iodide (MAPbI3) perovskite films processed entirely in open air (60–70% relative humidity) was investigated. Films were spin-coated on C-TiO2/MP-TiO2/ITO substrates and analysed in the same configuration used for graphite-electrode devices. X-ray diffraction confirmed tetragonal MAPbI3 (a ≈ 8.88Å, c ≈ 12.57Å) with Scherrer (110) crystallite sizes of 25.2, 26.9, and 25.1nm for the control, MAI, and FAI films, essentially unchanged across the series (dislocation density ∼1.4–1.6×1015 m−2). Scanning electron microscopy revealed mean surface grain sizes of 125, 128, and 128nm (with a broader distribution after MAI treatment) and film thicknesses of 1050, 1329, and 1064nm. Fourier-transform infrared spectroscopy showed a new ν(C=N) band at 1712 cm−1 unique to FAI and a high-frequency C–H shift to 2823 cm−1 for MAI, evidencing distinct, cation-specific surface chemical interactions, while Raman confirmed a methylammonium-libration mode emerging only after MAI treatment. Diffuse-reflectance Tauc analysis (directallowed, baseline-corrected) gave optical band gaps of 1.58, 1.55, and 1.66 eV for MAPbI3, MAPbI3+MAI, and MAPbI3+FAI, all consistent with tetragonal MAPbI3 (∼1.55–1.61 eV); rather than a bulk-gap shift, the optical signature of passivation appears as a 13nm red-shift of the photoluminescence maximum from the control to the FAI-treated film, indicating modified surface/near-surface recombination. To link these film-level changes to functional behaviour, the films were tested in a graphite electrode stack under a white-LED bench (Pin ≈ 6.1mW, 17 330 lx, A = 0.9 cm2, ≈0.07 sun, not AM1.5G); the relative response improved by ∼2.1× (MAI) and ∼3.6× (FAI) over the control, and a 16.7-h continuous-illumination stress test (100 successive J–V sweeps) showed a positive light-soaking response for both passivated films (light-soaking factor LSF = 1.75 for MAI and 1.85 for FAI; sweep-to-sweep variability ≤ 2.4%) against a flat, noisier control (LSF = 0.99, 5.2% variability). Overall, a direct same-batch comparison shows that FAI and MAI surface passivation induce distinct surface chemistries that improve the structural quality, optical signature, and operational photo-stability of open-air MAPbI3 films, providing a materials-level basis for selecting passivation chemistry in low-cost, humid-ambient fabrication.
- 1 June 2026
- Published by Elsevier in Physica B: Condensed Matter
- Vol. 739
Optical absorption enhancement driven by defect passivation in graphene oxide-modified CsPbBr3 perovskite
- 1 June 2026
- Published by Elsevier in Physica B: Condensed Matter
- Vol. 739
Optical absorption enhancement driven by defect passivation in graphene oxide-modified CsPbBr3 perovskite
- Open Access
- 11 May 2026
- Published by Green and Sustainable Materials Society in Greensusmater
- Vol. 3 (1) , 04
Design and Optimization of CsPbI3 Perovskite Solar Cells Using SCAPS-1D
This study investigates the optimization of CsPbI3-based perovskite solar cells using SCAPS-1D simulation with a device structure of FTO/ZnO/CsPbI3/Spiro-OMeTAD/metal. Key parameters, including absorber thickness, defect density, acceptor concentration, and transport layer properties, were systematically analyzed. The results show that absorber thickness significantly affects device performance, with an optimal thickness of 1.6 μm yielding an efficiency of 17.66%. Optimization of defect density and acceptor concentration further enhances device performance. After overall optimization, the power conversion efficiency increases from 16.3% to 23.1%, with Voc improving from 1.19 V to 1.39 V, Jsc from 18.33 to 20.5 mA/cm2, and FF from 75.2% to 87.4%. The improvement is supported by enhanced J–V characteristics and near-unity quantum efficiency over a wide wavelength range. These results demonstrate that parameter optimization plays a crucial role in achieving high-performance CsPbI3 perovskite solar cells.
- 11 May 2026
- Published by Green and Sustainable Materials Society in Greensusmater
- Vol. 3 (1) , 04
Open AccessDesign and Optimization of CsPbI3 Perovskite Solar Cells Using SCAPS-1D
This study investigates the optimization of CsPbI3-based perovskite solar cells using SCAPS-1D simulation with a device structure of FTO/ZnO/CsPbI3/Spiro-OMeTAD/metal. Key parameters, including absorber thickness, defect density, acceptor concentration, and transport layer properties, were systematically analyzed. The results show that absorber thickness significantly affects device performance, with an optimal thickness of 1.6 μm yielding an efficiency of 17.66%. Optimization of defect density and acceptor concentration further enhances device performance. After overall optimization, the power conversion efficiency increases from 16.3% to 23.1%, with Voc improving from 1.19 V to 1.39 V, Jsc from 18.33 to 20.5 mA/cm2, and FF from 75.2% to 87.4%. The improvement is supported by enhanced J–V characteristics and near-unity quantum efficiency over a wide wavelength range. These results demonstrate that parameter optimization plays a crucial role in achieving high-performance CsPbI3 perovskite solar cells.
- Open Access
- 13 April 2026
- Published by Elsevier in SSRN Electronic Journal
Molarity-Controlled FAI Surface Passivation for Enhanced Photovoltaic Performance of MAPbI3 Perovskite Solar Cells
In this paper, we study the effect of Formamidinium Iodide (FAI) layer with various molarities on the structural, morphological, optical, and photovoltaic properties of MAPbI3-based perovskite solar cells. FAI is used as a passivation layer of MAPbI3 perovskite, which is less thermodynamically stable. FAI has a greater number of hydrogen bonds between hydrogen ammonium cations and iodine ions in the organic framework, making the FAI structure more stable. The spin-coating method is used to deposit the solution onto the substrate surface. The addition of the FAI passivation layer is performed at molarities of 0.016, 0.032, 0.048, 0.064, and 0.080 M. As a result, the thickness of TiO2/MAPbI3/FAI layers variants increased from 907 nm (FAI 0.016) to 1594 nm (FAI 0.080). XRD analysis showed that the dislocation density and lattice strain decreased at FAI 0.032 and FAI 0.048. FTIR analysis confirmed the successful incorporation of FAI on the MAPbI3 surface, as indicated by the characteristic N-H, C-H, and C-N vibrational bands whose intensities increased with increasing FAI molarity. The bandgap decreased slightly from 1.50 eV to ~1.40 eV with increasing FAI molarity, indicating improved optical absorption associated with effective surface passivation of the MAPbI3 layer, as observed in UV-Vis and photoluminescence spectroscopy analyses. J-V measurements show that the PSC performance strongly depends on the FAI passivation molarity, with the highest power conversion efficiency obtained at FAI concentrations of 0.032 M. These results demonstrate that optimizing the FAI passivation molarity effectively improves the optical properties, reduces defect density, and enhances the photovoltaic performance of MAPbI3based perovskite solar cells.
- 13 April 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessMolarity-Controlled FAI Surface Passivation for Enhanced Photovoltaic Performance of MAPbI3 Perovskite Solar Cells
In this paper, we study the effect of Formamidinium Iodide (FAI) layer with various molarities on the structural, morphological, optical, and photovoltaic properties of MAPbI3-based perovskite solar cells. FAI is used as a passivation layer of MAPbI3 perovskite, which is less thermodynamically stable. FAI has a greater number of hydrogen bonds between hydrogen ammonium cations and iodine ions in the organic framework, making the FAI structure more stable. The spin-coating method is used to deposit the solution onto the substrate surface. The addition of the FAI passivation layer is performed at molarities of 0.016, 0.032, 0.048, 0.064, and 0.080 M. As a result, the thickness of TiO2/MAPbI3/FAI layers variants increased from 907 nm (FAI 0.016) to 1594 nm (FAI 0.080). XRD analysis showed that the dislocation density and lattice strain decreased at FAI 0.032 and FAI 0.048. FTIR analysis confirmed the successful incorporation of FAI on the MAPbI3 surface, as indicated by the characteristic N-H, C-H, and C-N vibrational bands whose intensities increased with increasing FAI molarity. The bandgap decreased slightly from 1.50 eV to ~1.40 eV with increasing FAI molarity, indicating improved optical absorption associated with effective surface passivation of the MAPbI3 layer, as observed in UV-Vis and photoluminescence spectroscopy analyses. J-V measurements show that the PSC performance strongly depends on the FAI passivation molarity, with the highest power conversion efficiency obtained at FAI concentrations of 0.032 M. These results demonstrate that optimizing the FAI passivation molarity effectively improves the optical properties, reduces defect density, and enhances the photovoltaic performance of MAPbI3based perovskite solar cells.