Yu Liu
Research Subjects
Yu Liu has a total of 118 co-authors. Here are the top co-authors by number of shared publications:
- Lijun Fu
State Key Laboratory of Materials‐Oriented Chemical Engineering, School of Energy Science and Engineering Nanjing Tech University Nanjing Jiangsu China
7 shared publications - Yuping Wu
Confucius Energy Storage Lab, School of Energy and Environment & Z Energy Storage Center, Southeast University, Nanjing 211189, China
7 shared publications - Yusong Zhu
School of Energy Science and Engineering, Jiangsu Key Laboratory of Process Enhancement and New Energy Equipment Technology, Nanjing Tech University, Nanjing 211816, Jiangsu Province, China
6 shared publications Weigang Wang
State Key Laboratory of Materials‐Oriented Chemical Engineering Institute of Advanced Materials (IAM) and College of Energy Science and Engineering Nanjing Tech University Nanjing 211800 China
5 shared publications- Wenqi Yan
Institute of Advanced Materials (IAM), Nanjing Tech University, Nanjing 210009, China
4 shared publications Dezhi Yang
State Key Laboratory of Materials-Oriented Chemical Engineering, College of Energy Science and Engineering and Institute of Advanced Materials, Nanjing Tech University, No.30, Puzhu Road (S), Nanjing, Jiangsu 211800, China
3 shared publications
Latest Publications
- 21 April 2026
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 14 (17) , 8284-8294
Synergistic Regulation of Interfacial Active Water and Zn Ion Flux for Achieving a Highly Reversible Zn Anode
- 21 April 2026
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 14 (17) , 8284-8294
Synergistic Regulation of Interfacial Active Water and Zn Ion Flux for Achieving a Highly Reversible Zn Anode
- 22 January 2025
- Published by Royal Society of Chemistry (RSC) in Energy & Environmental Science
- Vol. 18 (5) , 2353-2364
Non-destructive stripping electrochemistry enables long-life zinc metal batteries
Current research focuses on regulating Zn plating behavior to address the dendrite issue. Although significant improvements in the lifespans of symmetric batteries have been achieved, full batteries do not demonstrate a corresponding increase in the overall lifespan. The underlying reasons for this discrepancy remain unexplored. Herein, we identify that this performance mismatch is attributed to the neglect of the initial stripping behavior of the zinc anode in practical full batteries. This initial stripping, characterized by inherent inhomogeneities, causes anomalous and localized detachment of the interface layer. The incompleteness of the interface layer will result in the failure of its protection function. Then a non-destructive stripping strategy involving instantaneous repair of the damaged region is proposed to maintain the structural and functional integrity of the interface layer. During prolonged cycling, the copper–zinc species within the interface layer undergo irreversible phase reconstruction and spatial redistribution, which facilitate the de-solvation of hydrated Zn2+ and determine the plating of large-sized Zn(002). Utilizing this non-destructive anode, the full battery demonstrates a lifespan increase comparable to that of a symmetric battery, achieving an ultralong lifespan (1240 hours, 800 cycles) at a low current density (0.246 A g−1) with an ultrahigh cumulative capacity (847 mA h cm−2), and an Ah-level pouch cell exhibiting 150 stable cycles is also validated.
- 22 January 2025
- Published by Royal Society of Chemistry (RSC) in Energy & Environmental Science
- Vol. 18 (5) , 2353-2364
Non-destructive stripping electrochemistry enables long-life zinc metal batteries
Current research focuses on regulating Zn plating behavior to address the dendrite issue. Although significant improvements in the lifespans of symmetric batteries have been achieved, full batteries do not demonstrate a corresponding increase in the overall lifespan. The underlying reasons for this discrepancy remain unexplored. Herein, we identify that this performance mismatch is attributed to the neglect of the initial stripping behavior of the zinc anode in practical full batteries. This initial stripping, characterized by inherent inhomogeneities, causes anomalous and localized detachment of the interface layer. The incompleteness of the interface layer will result in the failure of its protection function. Then a non-destructive stripping strategy involving instantaneous repair of the damaged region is proposed to maintain the structural and functional integrity of the interface layer. During prolonged cycling, the copper–zinc species within the interface layer undergo irreversible phase reconstruction and spatial redistribution, which facilitate the de-solvation of hydrated Zn2+ and determine the plating of large-sized Zn(002). Utilizing this non-destructive anode, the full battery demonstrates a lifespan increase comparable to that of a symmetric battery, achieving an ultralong lifespan (1240 hours, 800 cycles) at a low current density (0.246 A g−1) with an ultrahigh cumulative capacity (847 mA h cm−2), and an Ah-level pouch cell exhibiting 150 stable cycles is also validated.
- Open Access
- 5 November 2021
- Published by American Association for the Advancement of Science (AAAS) in Science Advances
- Vol. 7 (45)
Spiral self-assembly of lamellar micelles into multi-shelled hollow nanospheres with unique chiral architecture
Shearing flow induced spiral self-assembly of multi-shelled nanospheres with unusual chirality in block copolymer micelle system.
- 5 November 2021
- Published by American Association for the Advancement of Science (AAAS) in Science Advances
- Vol. 7 (45)
Open AccessSpiral self-assembly of lamellar micelles into multi-shelled hollow nanospheres with unique chiral architecture
Shearing flow induced spiral self-assembly of multi-shelled nanospheres with unusual chirality in block copolymer micelle system.
- 31 July 2019
- Published by Wiley in Advanced Energy Materials
- Vol. 9 (34) , 1901379
A Large Scalable and Low‐Cost Sulfur/Nitrogen Dual‐Doped Hard Carbon as the Negative Electrode Material for High‐Performance Potassium‐Ion Batteries
Among the negative electrode materials for potassium ion batteries, carbon is very promising because of its low cost and environmental benignity. However, the relatively low storage capacity and sluggish kinetics still hinder its practical application. Herein, a large scalable sulfur/nitrogen dual‐doped hard carbon is prepared via a facile pyrolysis process with low‐cost sulfur and polyacrylonitrile as precursors. The dual‐doped hard carbon exhibits hierarchical structure, abundant defects, and functional groups. The material delivers a high reversible potassium storage capacity and excellent rate performance. In particular, a high reversible capacity of 213.7 and 144.9 mA h g−1 can be retained over 500 cycles at 0.1 A g−1 and 1200 cycles at 3 A g−1, respectively, demonstrating remarkable cycle stability at both low and high rates, superior to the other carbon materials reported for potassium storage, to the best of the authors' knowledge. Structure and kinetics studies suggest that the dual‐doping enhances the potassium diffusion and storage, profiting from the formation of a hierarchical structure, introduction of defects, and generation of increased graphitic and pyridinic N sites. This study demonstrates that a facile and scalable pyrolysis strategy is effective to realize hierarchical structure design and heteroatom doping of carbon, to achieve excellent potassium storage performance.
- 31 July 2019
- Published by Wiley in Advanced Energy Materials
- Vol. 9 (34) , 1901379
A Large Scalable and Low‐Cost Sulfur/Nitrogen Dual‐Doped Hard Carbon as the Negative Electrode Material for High‐Performance Potassium‐Ion Batteries
Among the negative electrode materials for potassium ion batteries, carbon is very promising because of its low cost and environmental benignity. However, the relatively low storage capacity and sluggish kinetics still hinder its practical application. Herein, a large scalable sulfur/nitrogen dual‐doped hard carbon is prepared via a facile pyrolysis process with low‐cost sulfur and polyacrylonitrile as precursors. The dual‐doped hard carbon exhibits hierarchical structure, abundant defects, and functional groups. The material delivers a high reversible potassium storage capacity and excellent rate performance. In particular, a high reversible capacity of 213.7 and 144.9 mA h g−1 can be retained over 500 cycles at 0.1 A g−1 and 1200 cycles at 3 A g−1, respectively, demonstrating remarkable cycle stability at both low and high rates, superior to the other carbon materials reported for potassium storage, to the best of the authors' knowledge. Structure and kinetics studies suggest that the dual‐doping enhances the potassium diffusion and storage, profiting from the formation of a hierarchical structure, introduction of defects, and generation of increased graphitic and pyridinic N sites. This study demonstrates that a facile and scalable pyrolysis strategy is effective to realize hierarchical structure design and heteroatom doping of carbon, to achieve excellent potassium storage performance.
- 23 July 2019
- Published by American Chemical Society (ACS) in ACS Applied Energy Materials
- Vol. 2 (8) , 5835-5842
A Low-Cost Zn-Based Aqueous Supercapacitor with High Energy Density
- 23 July 2019
- Published by American Chemical Society (ACS) in ACS Applied Energy Materials
- Vol. 2 (8) , 5835-5842
A Low-Cost Zn-Based Aqueous Supercapacitor with High Energy Density
- 7 May 2019
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 7 (22) , 13679-13686
An acetylene black modified gel polymer electrolyte for high-performance lithium–sulfur batteries
Lithium–sulfur (Li–S) batteries are considered to be a promising energy storage system for the future. However, a series of problems, such as sulfur acting as an insulator, the shuttle effect and the growth of lithium dendrites, have hindered their commercial application. To simultaneously tackle these three challenges, a composite quasi-solid/gel polymer electrolyte consisting of a nonporous supporting layer made by lightly cross-linked PMMA and a coated acetylene black layer was prepared to realize high-performance Li–S batteries. The nonporous polymer membrane was used to efficiently suppress the growth of lithium dendrites and promote the formation of a stable solid electrolyte interphase, while the acetylene black layer facing the sulfur cathode can hinder the polysulfide diffusion and promote rapid electron transfer. The as-prepared lithium–sulfur batteries show good cycling stability for 200 cycles, with an initial specific capacity of 994.5 mA h g−1 at 1C and perfect rate performance with a reversible capacity of 657.5 mA h g−1 at 3C. The growth of lithium dendrites was also effectively suppressed. This work provides a new concept for the structural design of Li–S batteries and promises to promote the further commercialization of Li–S batteries.
- 7 May 2019
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 7 (22) , 13679-13686
An acetylene black modified gel polymer electrolyte for high-performance lithium–sulfur batteries
Lithium–sulfur (Li–S) batteries are considered to be a promising energy storage system for the future. However, a series of problems, such as sulfur acting as an insulator, the shuttle effect and the growth of lithium dendrites, have hindered their commercial application. To simultaneously tackle these three challenges, a composite quasi-solid/gel polymer electrolyte consisting of a nonporous supporting layer made by lightly cross-linked PMMA and a coated acetylene black layer was prepared to realize high-performance Li–S batteries. The nonporous polymer membrane was used to efficiently suppress the growth of lithium dendrites and promote the formation of a stable solid electrolyte interphase, while the acetylene black layer facing the sulfur cathode can hinder the polysulfide diffusion and promote rapid electron transfer. The as-prepared lithium–sulfur batteries show good cycling stability for 200 cycles, with an initial specific capacity of 994.5 mA h g−1 at 1C and perfect rate performance with a reversible capacity of 657.5 mA h g−1 at 3C. The growth of lithium dendrites was also effectively suppressed. This work provides a new concept for the structural design of Li–S batteries and promises to promote the further commercialization of Li–S batteries.
- Open Access
- 1 January 2019
- Published by Elsevier in Canadian Journal of Cardiology
- Vol. 35 (1) , A5-A7
Table of Contents
- 1 January 2019
- Published by Elsevier in Canadian Journal of Cardiology
- Vol. 35 (1) , A5-A7
Open AccessTable of Contents
- 7 August 2018
- Published by Wiley in Advanced Materials Technologies
- Vol. 3 (9)
Advances of TiO2 as Negative Electrode Materials for Sodium‐Ion Batteries
TiO2 is a naturally abundant material with versatile polymorphs, which has been investigated in various fields, such as photocatalysis, electrochromic devices, lithium‐ion batteries, amongst others. Due to the similar (but not identical) chemistry between lithium and sodium, TiO2 is considered as an interesting potential negative electrode material for sodium ion batteries (SIBs) and is being investigated in fundamental studies for potential applications. The recent advances of TiO2 as negative electrode materials for SIBs are reviewed herein. Different electrochemical behaviors of TiO2 toward lithium and sodium are introduced. The (de)sodiation mechanism and physical parameters influencing the electrochemical performance are discussed. In addition, the strategies to improve the kinetic behavior, cycling stability, and coulombic efficiency of TiO2 negative electrode material for SIBs are reviewed. Beyond the great improvement of its electrochemical performance achieved, other challenges of TiO2 negative electrode material for SIBs remain. These challenges need to be addressed through a comprehensive understanding of its electrochemical behavior in SIBs. This review will be beneficial to the advancement of TiO2 for SIBs and other applications.
- 7 August 2018
- Published by Wiley in Advanced Materials Technologies
- Vol. 3 (9)
Advances of TiO2 as Negative Electrode Materials for Sodium‐Ion Batteries
TiO2 is a naturally abundant material with versatile polymorphs, which has been investigated in various fields, such as photocatalysis, electrochromic devices, lithium‐ion batteries, amongst others. Due to the similar (but not identical) chemistry between lithium and sodium, TiO2 is considered as an interesting potential negative electrode material for sodium ion batteries (SIBs) and is being investigated in fundamental studies for potential applications. The recent advances of TiO2 as negative electrode materials for SIBs are reviewed herein. Different electrochemical behaviors of TiO2 toward lithium and sodium are introduced. The (de)sodiation mechanism and physical parameters influencing the electrochemical performance are discussed. In addition, the strategies to improve the kinetic behavior, cycling stability, and coulombic efficiency of TiO2 negative electrode material for SIBs are reviewed. Beyond the great improvement of its electrochemical performance achieved, other challenges of TiO2 negative electrode material for SIBs remain. These challenges need to be addressed through a comprehensive understanding of its electrochemical behavior in SIBs. This review will be beneficial to the advancement of TiO2 for SIBs and other applications.