Zhipeng Zhou
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Zhipeng Zhou has a total of 36 co-authors. Here are the top co-authors by number of shared publications:
- Vincenzo Esposito
Technical University of Denmark
3 shared publications - Venkata Karthik Nadimpalli
Department of Civil and Mechanical Engineering, Technical University of Denmark, 2800 Kongens Lyngby, Denmark
2 shared publications - Aakil R. Lalwani
Department of Civil and Mechanical Engineering, Technical University of Denmark, Kongens Lyngby, Denmark
1 shared publication Aakil Raj Lalwani
1 shared publication- Akira Hosokawa
Faculty of Production Systems Engineering and Sciences, Komatsu University
1 shared publication - Alberto Basso
Department of Civil and Mechanical Engineering, Technical University of Denmark, Kongens Lyngby, Denmark
1 shared publication
Latest Publications
- 18 July 2025
- Published by Springer Nature in Nature Energy
- Vol. 10 (8) , 962-970
Monolithic gyroidal solid oxide cells by additive manufacturing
- 18 July 2025
- Published by Springer Nature in Nature Energy
- Vol. 10 (8) , 962-970
Monolithic gyroidal solid oxide cells by additive manufacturing
- 11 June 2025
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 145, 633-643
Life cycle environmental and cost assessment of the protonic ceramic electrolysis stack manufacturing
- 11 June 2025
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 145, 633-643
Life cycle environmental and cost assessment of the protonic ceramic electrolysis stack manufacturing
- Open Access
- 25 January 2023
- Published by Elsevier in Corrosion Science
- Vol. 214
Oxidation inhibition of 3D printed porous steel by ceria-activated multilayers
- 25 January 2023
- Published by Elsevier in Corrosion Science
- Vol. 214
Open AccessOxidation inhibition of 3D printed porous steel by ceria-activated multilayers
- Open Access
- 1 November 2021
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 15, 582-594
Revealing relationships between heterogeneous microstructure and strengthening mechanism of austenitic stainless steels fabricated by directed energy deposition (DED)
- 1 November 2021
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 15, 582-594
Open AccessRevealing relationships between heterogeneous microstructure and strengthening mechanism of austenitic stainless steels fabricated by directed energy deposition (DED)
- Open Access
Degradation Mechanisms of Metal-Supported Solid Oxide Cells and Countermeasures: A Review
Metal-supported oxide cells (MSCs) are considered as the third-generation solid oxide cells (SOCs) succeeding electrolyte-supported (first generation) and anode-supported (second generation) cells, which have gained much attention and progress in the past decade. The use of metal supports and advanced technical methods (such as infiltrated electrodes) has vastly improved cell performance, especially with its rapid startup ability and power density, showing a significant decrease in raw materials cost. However, new degradation mechanisms appeared, limiting the further improvement of the performance and lifetime. This review encapsulates the degradation mechanisms and countermeasures in the field of MSCs, reviewing the challenges and recommendations for future development.
Open AccessDegradation Mechanisms of Metal-Supported Solid Oxide Cells and Countermeasures: A Review
Metal-supported oxide cells (MSCs) are considered as the third-generation solid oxide cells (SOCs) succeeding electrolyte-supported (first generation) and anode-supported (second generation) cells, which have gained much attention and progress in the past decade. The use of metal supports and advanced technical methods (such as infiltrated electrodes) has vastly improved cell performance, especially with its rapid startup ability and power density, showing a significant decrease in raw materials cost. However, new degradation mechanisms appeared, limiting the further improvement of the performance and lifetime. This review encapsulates the degradation mechanisms and countermeasures in the field of MSCs, reviewing the challenges and recommendations for future development.
- Open Access
- 1 January 2004
- Published by Japan Society for Precision Engineering in Journal of the Japan Society for Precision Engineering, Contributed Papers
- Vol. 70 (12) , 1527-1532
Studies on High-Speed Milling with Small Ball End Mill
A new three-color infrared radiation pyrometer using an optical fiber is developed for measuring cutting temperature in high speed machining by small ball end mill. The high speed air spindle unit is adopted to the ordinary milling machine so that the maximum spindle revolution of 40000rpm is attainable. The ball radius of the carbide cutter is 3mm and the side cutting of carbon steel with ballnose is executed without cutting fluid. Cutting temperature distribution along the ball-nosed cutting-edge is measured. The influences of spindle rotational speed, radial depth of cut and feed per tooth on the temperature distribution at the flank face are examined. The maximum temperature of peripheral cutting edge about 700°C is obtained even at the rotation angle of 180° after cutting, and it drops along the ballnose toward the ball tip. Relatively large temperature gradient arises along the ball cutting-edge at higher spindle revolution because cutting speed depends on the local tool radius. Depth of cut and feed per tooth, at the same time, affect the overall temperature at the ball cutting edges. The cooling characteristics in air cutting reveals that the temperature difference during one cycle of intermittent cutting increases as spindle speed decreases. The relationship between the peripheral cutting speed and the tool temperature varies from tool shank to ball tip because the interactions between cutting edge and workpiece change along the ballnose.
- 1 January 2004
- Published by Japan Society for Precision Engineering in Journal of the Japan Society for Precision Engineering, Contributed Papers
- Vol. 70 (12) , 1527-1532
Open AccessStudies on High-Speed Milling with Small Ball End Mill
A new three-color infrared radiation pyrometer using an optical fiber is developed for measuring cutting temperature in high speed machining by small ball end mill. The high speed air spindle unit is adopted to the ordinary milling machine so that the maximum spindle revolution of 40000rpm is attainable. The ball radius of the carbide cutter is 3mm and the side cutting of carbon steel with ballnose is executed without cutting fluid. Cutting temperature distribution along the ball-nosed cutting-edge is measured. The influences of spindle rotational speed, radial depth of cut and feed per tooth on the temperature distribution at the flank face are examined. The maximum temperature of peripheral cutting edge about 700°C is obtained even at the rotation angle of 180° after cutting, and it drops along the ballnose toward the ball tip. Relatively large temperature gradient arises along the ball cutting-edge at higher spindle revolution because cutting speed depends on the local tool radius. Depth of cut and feed per tooth, at the same time, affect the overall temperature at the ball cutting edges. The cooling characteristics in air cutting reveals that the temperature difference during one cycle of intermittent cutting increases as spindle speed decreases. The relationship between the peripheral cutting speed and the tool temperature varies from tool shank to ball tip because the interactions between cutting edge and workpiece change along the ballnose.