Liang Hu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Liang Hu has a total of 41 co-authors. Here are the top co-authors by number of shared publications:
- Bingbo Wei
MOE Key Laboratory of Materials Physics and Chemistry under Extraordinary Conditions, School of Physical Science and Technology, Northwestern Polytechnical University , Xi'an 710072
16 shared publications - Hai-Peng Wang
School of Physical Science and Technology, Northwestern Polytechnical University , Xi’an 710072
8 shared publications - ZiXuan Wan
MOE Key Laboratory of Materials Physics and Chemistry under Extraordinary Conditions, School of Physical Science and Technology, Northwestern Polytechnical University , Xi'an 710072
7 shared publications - Chenhui Zheng
School of Physical Science and Technology, Northwestern Polytechnical University , Xi’an 710072
5 shared publications - B. W. Wu
School of Physical Science and Technology, Northwestern Polytechnical University , Xi'an 710072
4 shared publications - Dingnan Liu
School of Physical Science and Technology, Northwestern Polytechnical University , Xi’an 710072
4 shared publications
Latest Publications
- 26 August 2026
- Published by Elsevier in Acta Materialia
- Vol. 320
Dendrite growth kinetics and grain structure anisotropy of ultrahigh temperature W25Ta25Mo25Nb25 high-entropy alloy
- 26 August 2026
- Published by Elsevier in Acta Materialia
- Vol. 320
Dendrite growth kinetics and grain structure anisotropy of ultrahigh temperature W25Ta25Mo25Nb25 high-entropy alloy
- 2 July 2026
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 140 (1)
Space manufacturing-oriented prediction and control strategy of solidification shrinkage for ultrahigh temperature alloys
Freezing shrinkage is an inherent phenomenon for liquid alloys and becomes particularly critical in a space microgravity environment, where the suppression of natural convection and the absence of container walls fundamentally alter the solidification process. To clarify the governing mechanisms, containerless rapid solidification experiments are conducted aboard the China Space Station under controlled undercooling conditions. By combining measured thermophysical properties with calculated internal flow velocities, both the phase-transition volume contraction and the liquid feeding capability are quantified during solidification. A new dimensionless shrinkage criterion is established by comparing these two competing effects, enabling the evaluation of local shrinkage risk. The criterion successfully predicts shrinkage risk across different undercooling levels and shows strong agreement with experimental observations. This work provides a practical framework for assessing shrinkage behavior in microgravity and supports the development of defect control in future space-manufactured materials.
- 2 July 2026
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 140 (1)
Space manufacturing-oriented prediction and control strategy of solidification shrinkage for ultrahigh temperature alloys
Freezing shrinkage is an inherent phenomenon for liquid alloys and becomes particularly critical in a space microgravity environment, where the suppression of natural convection and the absence of container walls fundamentally alter the solidification process. To clarify the governing mechanisms, containerless rapid solidification experiments are conducted aboard the China Space Station under controlled undercooling conditions. By combining measured thermophysical properties with calculated internal flow velocities, both the phase-transition volume contraction and the liquid feeding capability are quantified during solidification. A new dimensionless shrinkage criterion is established by comparing these two competing effects, enabling the evaluation of local shrinkage risk. The criterion successfully predicts shrinkage risk across different undercooling levels and shows strong agreement with experimental observations. This work provides a practical framework for assessing shrinkage behavior in microgravity and supports the development of defect control in future space-manufactured materials.
- 29 June 2026
- Published by Elsevier in Scripta Materialia
- Vol. 284
Containerless rapid solidification and microscopic mechanical properties of hypoperitectic Mg-6.5 at.%La alloy
- 29 June 2026
- Published by Elsevier in Scripta Materialia
- Vol. 284
Containerless rapid solidification and microscopic mechanical properties of hypoperitectic Mg-6.5 at.%La alloy
- 1 April 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (4)
Space microgravity enhanced fractal dendrite coverage on solidifying alloy droplet surface
Under terrestrial gravity, alloy solidification is significantly influenced by temperature gradients, intense natural convection, and non-uniform solute redistribution, often leading to preferential dendritic growth and reduced structural symmetry. This article investigates dendritic growth in levitated Ti47.5Ni47.5V5 alloy droplets under microgravity, where buoyancy-driven convection is strongly suppressed, and Marangoni convection becomes the dominant flow mechanism. With the Marangoni number of Ma ≈ 4, the velocity ratio between dendritic growth and liquid flow of vd/vL ∼ 104 indicates that the solidification front propagates much faster than the interfacial flow. Therefore, dendritic growth is primarily governed by diffusion, resulting in nearly isotropic branching and highly symmetrical microstructures. Increased undercooling further enhances the fractal dimension and spatial filling efficiency through its effect on dendritic growth kinetics. The findings provide quantitative implications of weak Marangoni transport and rapid interfacial instability during phase change and establish a benchmark for understanding how Marangoni convection perturbs interfacial dynamics in rapid solidification systems under microgravity.
- 1 April 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (4)
Space microgravity enhanced fractal dendrite coverage on solidifying alloy droplet surface
Under terrestrial gravity, alloy solidification is significantly influenced by temperature gradients, intense natural convection, and non-uniform solute redistribution, often leading to preferential dendritic growth and reduced structural symmetry. This article investigates dendritic growth in levitated Ti47.5Ni47.5V5 alloy droplets under microgravity, where buoyancy-driven convection is strongly suppressed, and Marangoni convection becomes the dominant flow mechanism. With the Marangoni number of Ma ≈ 4, the velocity ratio between dendritic growth and liquid flow of vd/vL ∼ 104 indicates that the solidification front propagates much faster than the interfacial flow. Therefore, dendritic growth is primarily governed by diffusion, resulting in nearly isotropic branching and highly symmetrical microstructures. Increased undercooling further enhances the fractal dimension and spatial filling efficiency through its effect on dendritic growth kinetics. The findings provide quantitative implications of weak Marangoni transport and rapid interfacial instability during phase change and establish a benchmark for understanding how Marangoni convection perturbs interfacial dynamics in rapid solidification systems under microgravity.
- Open Access
- 17 February 2026
- Published by Elsevier in SSRN Electronic Journal
Containerless Rapid Solidification and Microscopic Mechanical Properties of Hypoperitectic Mg-6.5 at.%La Alloy
The rapid solidification mechanism of hypoperitectic Mg-6.5 at.% La alloy was investigated by containerless processing via drop tube technique. Typical peritectic solidification prevailed at liquid undercoolings lower than the critical value of 40 K. Once alloy undercooling exceeded 40 K, the nucleation and growth of primary Mg17La2 phase were suppressed, leading to the direct nucleation of peritectic Mg12La phase. The volume fraction of Mg12La compound increased and its actual La content decreased with alloy undercooling, which was accompanied with remarkable dendritic structure refinement. Almost segregationless solidification took place at the maximum liquid undercooling of 182 K (0.19 TL). Mg12La dendrites exhibited great nano-hardness and elastic modulus at various liquid undercoolings. In particular, a maximum average Vickers hardness of 210.7 HV was achieved at 124 K undercooling, representing a 34% enhancement over master alloy.
- 17 February 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessContainerless Rapid Solidification and Microscopic Mechanical Properties of Hypoperitectic Mg-6.5 at.%La Alloy
The rapid solidification mechanism of hypoperitectic Mg-6.5 at.% La alloy was investigated by containerless processing via drop tube technique. Typical peritectic solidification prevailed at liquid undercoolings lower than the critical value of 40 K. Once alloy undercooling exceeded 40 K, the nucleation and growth of primary Mg17La2 phase were suppressed, leading to the direct nucleation of peritectic Mg12La phase. The volume fraction of Mg12La compound increased and its actual La content decreased with alloy undercooling, which was accompanied with remarkable dendritic structure refinement. Almost segregationless solidification took place at the maximum liquid undercooling of 182 K (0.19 TL). Mg12La dendrites exhibited great nano-hardness and elastic modulus at various liquid undercoolings. In particular, a maximum average Vickers hardness of 210.7 HV was achieved at 124 K undercooling, representing a 34% enhancement over master alloy.
- 30 September 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 127 (13)
Competitive nucleation and dendritic growth of βNb5Si3 and Nb3Si intermetallic compounds within liquid Nb-25 at. % Si alloy under electrostatic levitation condition
The rapid solidification mechanism of the peritectic Nb-25 at. % Si alloy was investigated via the electrostatic levitation technique, where liquid undercooling attained 486 K (0.2TL). The dendritic growth process of primary phase was observed in situ by high-speed photography. If liquid undercooling was below 443 K, the primary phase was characterized by coarse βNb5Si3 dendrites, and their maximum growth velocity measured 93 mm/s at 434 K. In the interdendritic zone, a small amount of Nb3Si phase was produced by the peritectic reaction and then decomposed through eutectoid transformation. Once liquid undercooling increased above the threshold of 443 K, peritectic Nb3Si phase would nucleate and grow preferentially. The growth velocity of Nb3Si phase increased rapidly with the rise of undercooling, attaining 248 mm/s at the maximum undercooling of 486 K. Because of the high cooling rates during electrostatic levitation, the allotropic transformation from βNb5Si3 to αNb5Si3 was suppressed.
- 30 September 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 127 (13)
Competitive nucleation and dendritic growth of βNb5Si3 and Nb3Si intermetallic compounds within liquid Nb-25 at. % Si alloy under electrostatic levitation condition
The rapid solidification mechanism of the peritectic Nb-25 at. % Si alloy was investigated via the electrostatic levitation technique, where liquid undercooling attained 486 K (0.2TL). The dendritic growth process of primary phase was observed in situ by high-speed photography. If liquid undercooling was below 443 K, the primary phase was characterized by coarse βNb5Si3 dendrites, and their maximum growth velocity measured 93 mm/s at 434 K. In the interdendritic zone, a small amount of Nb3Si phase was produced by the peritectic reaction and then decomposed through eutectoid transformation. Once liquid undercooling increased above the threshold of 443 K, peritectic Nb3Si phase would nucleate and grow preferentially. The growth velocity of Nb3Si phase increased rapidly with the rise of undercooling, attaining 248 mm/s at the maximum undercooling of 486 K. Because of the high cooling rates during electrostatic levitation, the allotropic transformation from βNb5Si3 to αNb5Si3 was suppressed.
- 18 September 2025
- Published by Elsevier in Intermetallics
- Vol. 187
Undercooled liquid state properties and intermetallic compounds growth of ternary Fe-Tb-B alloy
- 18 September 2025
- Published by Elsevier in Intermetallics
- Vol. 187
Undercooled liquid state properties and intermetallic compounds growth of ternary Fe-Tb-B alloy
- 4 June 2025
- Published by Elsevier in Acta Materialia
- Vol. 295
Eutectic growth kinetics and microscopic mechanical property of refractory Zr57V43 alloy under space and ground conditions
- 4 June 2025
- Published by Elsevier in Acta Materialia
- Vol. 295
Eutectic growth kinetics and microscopic mechanical property of refractory Zr57V43 alloy under space and ground conditions
- Open Access
- 3 June 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 137 (21)
Liquid state properties and rapid solidification mechanisms of ternary Fe–Dy–B alloy
The thermophysical properties and rapid solidification kinetics of stable and metastable liquid Fe84Dy8B8 alloy were investigated by electromagnetic levitation and drop tube techniques, which achieved maximum undercoolings of 215 K (0.14 TL) and 386 K (0.25 TL), respectively. The surface tension, viscosity, and diffusivity of liquid alloy were measured, and their correlations with liquid undercooling were derived, through which the activation energies for viscous flow and atomic diffusion were determined. At small undercoolings, the primary γFe phase growth velocity rose continuously as a power function. The increase of bulk undercooling not only significantly promoted the formation of pseudobinary eutectics by involving Dy2Fe17(B) as the main phase but also raised the volume fraction of peri-eutectics to some extent. At the intermediate undercooling regime, the Dy2Fe17(B) phase grew as the leading phase and was significantly refined with undercooling, and the following peri-eutectic transition was greatly accelerated, rendering the τ1 (Dy2Fe14B) dominant phase of solidification microstructure. When substantial undercoolings were achieved in alloy droplets, the τ1 phase nucleated and grew directly from the undercooled alloy and underwent a faceted to nonfaceted growth mode transition, whose maximum volume fraction reached up to 81%. This indicates that high undercooling rapid solidification is an effective approach to modulate the volume fraction of the τ1 phase by accelerating its peri-eutectic transition or even inducing its direct formation in rare earth alloys.
- 3 June 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 137 (21)
Open AccessLiquid state properties and rapid solidification mechanisms of ternary Fe–Dy–B alloy
The thermophysical properties and rapid solidification kinetics of stable and metastable liquid Fe84Dy8B8 alloy were investigated by electromagnetic levitation and drop tube techniques, which achieved maximum undercoolings of 215 K (0.14 TL) and 386 K (0.25 TL), respectively. The surface tension, viscosity, and diffusivity of liquid alloy were measured, and their correlations with liquid undercooling were derived, through which the activation energies for viscous flow and atomic diffusion were determined. At small undercoolings, the primary γFe phase growth velocity rose continuously as a power function. The increase of bulk undercooling not only significantly promoted the formation of pseudobinary eutectics by involving Dy2Fe17(B) as the main phase but also raised the volume fraction of peri-eutectics to some extent. At the intermediate undercooling regime, the Dy2Fe17(B) phase grew as the leading phase and was significantly refined with undercooling, and the following peri-eutectic transition was greatly accelerated, rendering the τ1 (Dy2Fe14B) dominant phase of solidification microstructure. When substantial undercoolings were achieved in alloy droplets, the τ1 phase nucleated and grew directly from the undercooled alloy and underwent a faceted to nonfaceted growth mode transition, whose maximum volume fraction reached up to 81%. This indicates that high undercooling rapid solidification is an effective approach to modulate the volume fraction of the τ1 phase by accelerating its peri-eutectic transition or even inducing its direct formation in rare earth alloys.
- Open Access
- 8 April 2025
- Published by Elsevier in Review of Materials Research
- Vol. 1 (1)
Space station based experimental research on thermophysical properties and solidification mechanisms of Fe-19%Si alloy
- 8 April 2025
- Published by Elsevier in Review of Materials Research
- Vol. 1 (1)
Open AccessSpace station based experimental research on thermophysical properties and solidification mechanisms of Fe-19%Si alloy