Mahima Arrawatia
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mahima Arrawatia has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Anamika Verma
Indian Institute Technology Bombay, Mumbai, India
2 shared publications - Girish Kumar
Department of Electrical Engineering, IIT Bombay, Mumbai, India
2 shared publications Nagarjuna Nallam
Department of Electrical Engineering, Indian Institute of Technology Kanpur, Kanpur, India
1 shared publication- Praveen Saraswat
Department of Electronics and Electrical Engineering, Indian Institute of Technology Guwahati, Guwahati, Assam, India
1 shared publication - Uday Maurya
Department of Electronics and Electrical Engineering, Indian Institute of Technology Guwahati, Guwahati, India
1 shared publication
Latest Publications
- 30 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 74 (3) , 2514-2525
A mm-Wave TR Front-End Module With Reconfigurable High-Power and Low-Power Transmit Mode in 65-nm CMOS
This article presents the analysis, design, and implementation of a millimeter-wave (mm-wave) transmit (Tx) and receive (Rx) front-end module (FEM) with reconfigurable Tx power modes in a 65-nm bulk CMOS process. A power amplifier is implemented with reconfigurable low-power mode (LPM) and high-power mode (HPM). A compact output network with a footprint of two inductors is designed to provide optimum impedance for both the PA modes and differential to single-ended conversion in Tx mode. A theoretical analysis of the proposed network in both the PA modes and T/R switch operation is also presented. The network only has a loss of 0.8 dB from 35 to 43GHz. In the Rx mode, the PA cell is used as a switch, and the PA output network provides a high impedance to the antenna. A transformer-based differential source degenerated low-noise amplifier (LNA) is implemented. The measured saturated output power of the PA in HPM is 18 dBm at 37 GHz with a peak PAE of 18%. In LPM, the PA has a peak power of 14.4 dBm with a peak efficiency of 17.8%. The peak gain of the PA is 15 dB in LPM and 21 dB at HPM at 37 GHz. The FEM has a variation of only 1 dB in the simulated saturated power for a 2.5:1 VSWR in the HPM mode. The LNA has a minimum noise figure (NF) of 5.6 dB at 42 GHz with a peak gain of 20 dB. The Rx achieves the measured 3-dB gain bandwidth from 36 to 44 GHz. The size of the output network is 0.09 mm2.
- 30 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 74 (3) , 2514-2525
A mm-Wave TR Front-End Module With Reconfigurable High-Power and Low-Power Transmit Mode in 65-nm CMOS
This article presents the analysis, design, and implementation of a millimeter-wave (mm-wave) transmit (Tx) and receive (Rx) front-end module (FEM) with reconfigurable Tx power modes in a 65-nm bulk CMOS process. A power amplifier is implemented with reconfigurable low-power mode (LPM) and high-power mode (HPM). A compact output network with a footprint of two inductors is designed to provide optimum impedance for both the PA modes and differential to single-ended conversion in Tx mode. A theoretical analysis of the proposed network in both the PA modes and T/R switch operation is also presented. The network only has a loss of 0.8 dB from 35 to 43GHz. In the Rx mode, the PA cell is used as a switch, and the PA output network provides a high impedance to the antenna. A transformer-based differential source degenerated low-noise amplifier (LNA) is implemented. The measured saturated output power of the PA in HPM is 18 dBm at 37 GHz with a peak PAE of 18%. In LPM, the PA has a peak power of 14.4 dBm with a peak efficiency of 17.8%. The peak gain of the PA is 15 dB in LPM and 21 dB at HPM at 37 GHz. The FEM has a variation of only 1 dB in the simulated saturated power for a 2.5:1 VSWR in the HPM mode. The LNA has a minimum noise figure (NF) of 5.6 dB at 42 GHz with a peak gain of 20 dB. The Rx achieves the measured 3-dB gain bandwidth from 36 to 44 GHz. The size of the output network is 0.09 mm2.
- Open Access
- 3 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Circuits and Systems
- Vol. 6, 414-423
A Low-Loss T/R Module With Balanced Power Amplifier for High Antenna Impedance Tolerance
The balanced power amplifier (BPA) topology is commonly used in applications requiring high antenna impedance tolerance. This paper presents a low-loss transmit-receive (T/R) front-end module (FEM) with BPA using four shunt switches. These switches are embedded into the output network of the BPA and the input matching network of the common source low noise amplifier (LNA). A prototype T/R FEM is implemented in bulk CMOS 65 nm technology for the 5G FR2 n260 band. As per simulations, the extra loss due to the T/R interface in transmit mode is 0.75 dB, and the noise figure (NF) degradation in receive mode is 1.5 dB. The prototype chip is characterized by die-probing. The BPA delivers a saturated power output of +18 dBm with a power-added efficiency (PAE) of 14.5 % at 40 GHz in measurements. The LNA has a gain of 21.3 dB and a noise figure of 5.8 dB in the n260 band.
- 3 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Circuits and Systems
- Vol. 6, 414-423
Open AccessA Low-Loss T/R Module With Balanced Power Amplifier for High Antenna Impedance Tolerance
The balanced power amplifier (BPA) topology is commonly used in applications requiring high antenna impedance tolerance. This paper presents a low-loss transmit-receive (T/R) front-end module (FEM) with BPA using four shunt switches. These switches are embedded into the output network of the BPA and the input matching network of the common source low noise amplifier (LNA). A prototype T/R FEM is implemented in bulk CMOS 65 nm technology for the 5G FR2 n260 band. As per simulations, the extra loss due to the T/R interface in transmit mode is 0.75 dB, and the noise figure (NF) degradation in receive mode is 1.5 dB. The prototype chip is characterized by die-probing. The BPA delivers a saturated power output of +18 dBm with a power-added efficiency (PAE) of 14.5 % at 40 GHz in measurements. The LNA has a gain of 21.3 dB and a noise figure of 5.8 dB in the n260 band.
- 30 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 70 (11) , 11183-11187
High Gain Wideband Circularly Polarized Microstrip Antenna Array
A wideband high gain circularly polarized microstrip antenna (CP MSA) array is presented in this paper. In the proposed CP MSA array, the elements are designed at 3.5 GHz and 5.8 GHz, which are sequentially rotated to form a planar array. The array elements are fed using TM 110 and TM 210 modes of a center CP MSA. This arrangement achieves an AR bandwidth of 63.7% (3.25–6.29 GHz) and improves gain over a wide bandwidth. The peak gain of the array is 17.77 dBic with a 3 dB gain bandwidth of 53.9%. The center MSA of the array is fed using four-orthogonal printed L-probes with quadrature phase difference. The proposed CP MSA array has | S 11 | ≤ -10 dB bandwidth of 63.3% (3.32–6.4 GHz).
- 30 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 70 (11) , 11183-11187
High Gain Wideband Circularly Polarized Microstrip Antenna Array
A wideband high gain circularly polarized microstrip antenna (CP MSA) array is presented in this paper. In the proposed CP MSA array, the elements are designed at 3.5 GHz and 5.8 GHz, which are sequentially rotated to form a planar array. The array elements are fed using TM 110 and TM 210 modes of a center CP MSA. This arrangement achieves an AR bandwidth of 63.7% (3.25–6.29 GHz) and improves gain over a wide bandwidth. The peak gain of the array is 17.77 dBic with a 3 dB gain bandwidth of 53.9%. The center MSA of the array is fed using four-orthogonal printed L-probes with quadrature phase difference. The proposed CP MSA array has | S 11 | ≤ -10 dB bandwidth of 63.3% (3.32–6.4 GHz).
- 5 April 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 20 (6) , 1058-1062
Low-Profile Wideband High-Gain Folded Dipole Antenna
A low profile broadband folded dipole antenna with high gain is presented in this paper. Folded dipole antenna is utilized to reduce the height of the reflector to 0.1, without degrading the impedance bandwidth. Parasitic patches shorted to the reflector are employed to reduce the gain variation of the antenna. The |S11 | -10dB bandwidth of the antenna is from 1.18 to 4.08 GHz (110 %) with a broadside gain of 9.25 1.25 dBi over the bandwidth of 1.27-4.03 (103.8%). The radiation pattern variation of the antenna is small over the bandwidth. The cross-polar level is below -25 dB from 1.18 to 3.4 GHz. The dimensions of the antenna are 0.78 0.78 0.10, where corresponds to the lowest frequency.
- 5 April 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 20 (6) , 1058-1062
Low-Profile Wideband High-Gain Folded Dipole Antenna
A low profile broadband folded dipole antenna with high gain is presented in this paper. Folded dipole antenna is utilized to reduce the height of the reflector to 0.1, without degrading the impedance bandwidth. Parasitic patches shorted to the reflector are employed to reduce the gain variation of the antenna. The |S11 | -10dB bandwidth of the antenna is from 1.18 to 4.08 GHz (110 %) with a broadside gain of 9.25 1.25 dBi over the bandwidth of 1.27-4.03 (103.8%). The radiation pattern variation of the antenna is small over the bandwidth. The cross-polar level is below -25 dB from 1.18 to 3.4 GHz. The dimensions of the antenna are 0.78 0.78 0.10, where corresponds to the lowest frequency.