Wentao Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Wentao Wang has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Linbing Wang
School of Environmental, Civil, Agricultural and Mechanical Engineering, University of Georgia, Athens, GA 30602, USA
11 shared publications - Kang Zhao
School of Civil and Architectural Engineering Liaoning University of Technology Jinzhou China
4 shared publications - Huifang Liu
National Center for Materials Service Safety, University of Science and Technology Beijing (USTB), Beijing 100083, China
3 shared publications - Yinghao Miao
National Center for Materials Service Safety, University of Science and Technology Beijing, Beijing 100083, China
3 shared publications - Hailu Yang
National Center for Materials Service Safety, University of Science and Technology Beijing, Beijing 100083, China
2 shared publications - Hua Rong
Wuzhou Engineering Group Corporation Ltd., Beijing 100083, China
2 shared publications
Latest Publications
- Open Access
Sustainability in Asphalt, Concrete and Other Pavement Materials: Design, Performance, and Characterization
With the continuous growth of global infrastructure construction and increasing environmental pressures
Open AccessSustainability in Asphalt, Concrete and Other Pavement Materials: Design, Performance, and Characterization
With the continuous growth of global infrastructure construction and increasing environmental pressures
- Open Access
Evaluation of Moisture Damage in Asphalt Mixtures Under Dynamic Water Pressure Using 3D Laser Scanning
Under continuous erosion of dynamic water pressure generated by vehicle–water–pavement coupling interaction, asphalt mixture will gradually deteriorate and severe moisture damage finally emerges. The fine aggregate mixture (FAM) component is notably eroded and stripped, while the aggregate component even cracks sometimes. Sufficient attention has not been paid to these critical phenomena. This study employed the 3D laser scanning technique to detect changes in surface roughness of the asphalt mixture before and after it was eroded by dynamic water pressure. The degree of erosion of the asphalt mixture, FAM component, and aggregate component were thereby evaluated. The influences of experimental parameters such as water temperature and pore water pressure magnitude, as well as variable parameters including lithology and asphalt type, were also taken into account. By integrating the detection of physical and mechanical properties evolution of aggregates, the mechanism of moisture damage was comprehensively illustrated from the perspectives of both components of FAM and aggregate. The findings revealed that the 3D laser scanning technique could clearly detect and quantitatively assess the morphological changes on the asphalt mixture surface after been eroded in dynamic water pressure. Both types of asphalt mixtures exhibited varying degrees of erosion and wear, and obvious increases in surface unevenness were observed in each case. Variations in either temperature or pore water pressure magnitude showed limited influence on moisture damage in basalt-based asphalt mixture. In contrast, moisture damage sustained by limestone-based asphalt mixture was notably sensitive to temperature changes but remained largely insensitive to fluctuations in pore water pressure magnitude. The increase in surface roughness of asphalt mixture was primarily attributed to the scouring action of dynamic water pressure, which removed the FAM component surrounding coarse aggregate particles. Degradation in coarse aggregate particles would lead to the deterioration of the entire asphalt mixture. The compatibility between the stripping rate of FAM component and the deterioration rate of coarse aggregate governed the macroscopic manifestation of overall moisture damage in the asphalt mixture.
Open AccessEvaluation of Moisture Damage in Asphalt Mixtures Under Dynamic Water Pressure Using 3D Laser Scanning
Under continuous erosion of dynamic water pressure generated by vehicle–water–pavement coupling interaction, asphalt mixture will gradually deteriorate and severe moisture damage finally emerges. The fine aggregate mixture (FAM) component is notably eroded and stripped, while the aggregate component even cracks sometimes. Sufficient attention has not been paid to these critical phenomena. This study employed the 3D laser scanning technique to detect changes in surface roughness of the asphalt mixture before and after it was eroded by dynamic water pressure. The degree of erosion of the asphalt mixture, FAM component, and aggregate component were thereby evaluated. The influences of experimental parameters such as water temperature and pore water pressure magnitude, as well as variable parameters including lithology and asphalt type, were also taken into account. By integrating the detection of physical and mechanical properties evolution of aggregates, the mechanism of moisture damage was comprehensively illustrated from the perspectives of both components of FAM and aggregate. The findings revealed that the 3D laser scanning technique could clearly detect and quantitatively assess the morphological changes on the asphalt mixture surface after been eroded in dynamic water pressure. Both types of asphalt mixtures exhibited varying degrees of erosion and wear, and obvious increases in surface unevenness were observed in each case. Variations in either temperature or pore water pressure magnitude showed limited influence on moisture damage in basalt-based asphalt mixture. In contrast, moisture damage sustained by limestone-based asphalt mixture was notably sensitive to temperature changes but remained largely insensitive to fluctuations in pore water pressure magnitude. The increase in surface roughness of asphalt mixture was primarily attributed to the scouring action of dynamic water pressure, which removed the FAM component surrounding coarse aggregate particles. Degradation in coarse aggregate particles would lead to the deterioration of the entire asphalt mixture. The compatibility between the stripping rate of FAM component and the deterioration rate of coarse aggregate governed the macroscopic manifestation of overall moisture damage in the asphalt mixture.
- Open Access
- 1 April 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (7) , 3433
Characterization of Vehicle Tire Hydroplaning Using Numerical Simulation and Field Full-Scale Accelerated Loading Methods
Increasingly frequent extreme rainfall commonly leads to water accumulation on the road surface, elevating vehicle tire hydroplaning to a major threat to driving safety. Existing research mainly focused on tire model optimization or predicting critical hydroplaning speed features based on empirical formulas and numerical simulations. However, there is a lack of systematic validation of the tire–water–pavement coupling interaction under realistic pavement conditions, with particular insufficient attention paid to pavement dynamic responses. In this study, numerical simulation and field full-scale accelerated loading methods were applied to investigate dynamic response characteristics of the tire–water–pavement coupling interaction system. Parametric analyses were first performed to investigate the influences of vehicle speed, vehicle load, water-film thickness, and tire lateral position on the mechanical behaviors of the fluid–structure interaction for a moving vehicle tire. Subsequently, field-measured dynamic responses’ features were used to validate the numerical model, which was then further applied to predict critical conditions of vehicle tire hydroplaning. Finally, the mechanisms of hydroplaning and corresponding mitigation measures were discussed. The study revealed that increasing vehicle speed and water-film thickness, as well as decreasing vehicle load, would reduce the pavement supporting force. The tire–pavement contact stress and strain decreased from the vehicle tire’s center position towards its shoulders. The predicted critical hydroplaning condition suggested that increasing vehicle load mitigated hydroplaning by reducing the proportion of water-induced hydrodynamic lifting force relative to the total vehicle load. When the water depth is relatively shallow, the hydroplaning risk increases rapidly with water depth, while the water’s adverse impact on tire–pavement contact force gradually diminishes as water depth continues to increase. It implies that a vehicle with a relatively low axle load driving on the pavement with a thin thickness of retained water in light rain will still face the hydroplaning risk, as the pavement’s supporting force may be substantially reduced in this weather. The findings provide theoretical foundations and experimentally supported insights on driving safety assessment and anti-skid design of water-covered pavement.
- 1 April 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (7) , 3433
Open AccessCharacterization of Vehicle Tire Hydroplaning Using Numerical Simulation and Field Full-Scale Accelerated Loading Methods
Increasingly frequent extreme rainfall commonly leads to water accumulation on the road surface, elevating vehicle tire hydroplaning to a major threat to driving safety. Existing research mainly focused on tire model optimization or predicting critical hydroplaning speed features based on empirical formulas and numerical simulations. However, there is a lack of systematic validation of the tire–water–pavement coupling interaction under realistic pavement conditions, with particular insufficient attention paid to pavement dynamic responses. In this study, numerical simulation and field full-scale accelerated loading methods were applied to investigate dynamic response characteristics of the tire–water–pavement coupling interaction system. Parametric analyses were first performed to investigate the influences of vehicle speed, vehicle load, water-film thickness, and tire lateral position on the mechanical behaviors of the fluid–structure interaction for a moving vehicle tire. Subsequently, field-measured dynamic responses’ features were used to validate the numerical model, which was then further applied to predict critical conditions of vehicle tire hydroplaning. Finally, the mechanisms of hydroplaning and corresponding mitigation measures were discussed. The study revealed that increasing vehicle speed and water-film thickness, as well as decreasing vehicle load, would reduce the pavement supporting force. The tire–pavement contact stress and strain decreased from the vehicle tire’s center position towards its shoulders. The predicted critical hydroplaning condition suggested that increasing vehicle load mitigated hydroplaning by reducing the proportion of water-induced hydrodynamic lifting force relative to the total vehicle load. When the water depth is relatively shallow, the hydroplaning risk increases rapidly with water depth, while the water’s adverse impact on tire–pavement contact force gradually diminishes as water depth continues to increase. It implies that a vehicle with a relatively low axle load driving on the pavement with a thin thickness of retained water in light rain will still face the hydroplaning risk, as the pavement’s supporting force may be substantially reduced in this weather. The findings provide theoretical foundations and experimentally supported insights on driving safety assessment and anti-skid design of water-covered pavement.
- Open Access
Characterization of Viscoelastic Performance and VOC Emission of Warm-Mixed SBS Asphalt Binder Under Different Dosages of Warm-Mixed Additive
Warm-mixed asphalt technology can significantly reduce the heating temperatures required for asphalt pavement construction, which makes it one of the crucial technical approaches in road engineering for achieving energy conservation and emission reduction, and carbon neutrality. Existing research often focuses on designing asphalt materials to ensure optimal service performance, but insufficient attention has been paid to the specific extent of reduction in asphalt fume emissions. However, the latter is a critical factor that cannot be neglected when constructing asphalt pavements in environmentally sensitive regions. Considering the environmental factor, this study systematically explores the comprehensive influence of different warm-mixed additive dosages on the viscoelastic properties and VOC emissions of warm-mixed SBS asphalt binder using rotational viscosity, bending beam rheometer (BBR), dynamic shear rheometer (DSR), and gas chromatography–mass spectrometry (GC-MS) test methods. The findings show that the application of warm-mixed additive does not compromise the comprehensive properties of SBS asphalt binder, but partially enhances its service performance instead. Due to the significant reduction in heating temperature, asphalt VOC emissions are indirectly reduced. Although the warm-mixed additive possesses a certain degree of volatility, its application still shows a significant trend toward emission reduction. Despite 0.4% being a relatively economical dosage of warm-mixed additive, a slight increase to 0.5% can achieve more pronounced environmental benefits in VOC emission reduction while maintaining comprehensive service performance that meets specification requirements. The findings can provide new insights for the application and decision-making of warm-mixed asphalt technology in environmentally sensitive regions.
Open AccessCharacterization of Viscoelastic Performance and VOC Emission of Warm-Mixed SBS Asphalt Binder Under Different Dosages of Warm-Mixed Additive
Warm-mixed asphalt technology can significantly reduce the heating temperatures required for asphalt pavement construction, which makes it one of the crucial technical approaches in road engineering for achieving energy conservation and emission reduction, and carbon neutrality. Existing research often focuses on designing asphalt materials to ensure optimal service performance, but insufficient attention has been paid to the specific extent of reduction in asphalt fume emissions. However, the latter is a critical factor that cannot be neglected when constructing asphalt pavements in environmentally sensitive regions. Considering the environmental factor, this study systematically explores the comprehensive influence of different warm-mixed additive dosages on the viscoelastic properties and VOC emissions of warm-mixed SBS asphalt binder using rotational viscosity, bending beam rheometer (BBR), dynamic shear rheometer (DSR), and gas chromatography–mass spectrometry (GC-MS) test methods. The findings show that the application of warm-mixed additive does not compromise the comprehensive properties of SBS asphalt binder, but partially enhances its service performance instead. Due to the significant reduction in heating temperature, asphalt VOC emissions are indirectly reduced. Although the warm-mixed additive possesses a certain degree of volatility, its application still shows a significant trend toward emission reduction. Despite 0.4% being a relatively economical dosage of warm-mixed additive, a slight increase to 0.5% can achieve more pronounced environmental benefits in VOC emission reduction while maintaining comprehensive service performance that meets specification requirements. The findings can provide new insights for the application and decision-making of warm-mixed asphalt technology in environmentally sensitive regions.
- Open Access
Review on Design, Characterization, and Prediction of Performance for Asphalt Materials and Asphalt Pavement Using Multi-Scale Numerical Simulation
Asphalt pavement, which is mainly made up of the asphalt mixture, exhibits complicated mechanical behaviors under the combined effects of moving vehicle loads and external service environments. Multi-scale numerical simulation can well characterize behaviors of asphalt materials and asphalt pavement, and the essential research progress is systematically summarized from an entire view. This paper reviews extensive research works concerning aspects of the design, characterization, and prediction of performance for asphalt materials and asphalt pavement based on multi-scale numerical simulation. Firstly, full-scale performance modeling on asphalt pavement is discussed from aspects of structural dynamic response, structural and material evaluation, and wheel–pavement interaction. The correlation between asphalt material properties and pavement performance is also analyzed, and so is the hydroplaning phenomenon. Macro- and mesoscale simulations on the mechanical property characterization of the asphalt mixture and its components are then investigated, while virtual proportion design for the asphalt mixture is introduced. Features of two-dimensional and three-dimensional microscale modeling on the asphalt mixture are summarized, followed by molecular dynamics simulation on asphalt binders, aggregates, and their interface, while nanoscale behavior modeling on asphalt binders is presented. Finally, aspects that need more attention concerning this study’s topic are discussed, and several suggestions for future investigations are also presented.
Open AccessReview on Design, Characterization, and Prediction of Performance for Asphalt Materials and Asphalt Pavement Using Multi-Scale Numerical Simulation
Asphalt pavement, which is mainly made up of the asphalt mixture, exhibits complicated mechanical behaviors under the combined effects of moving vehicle loads and external service environments. Multi-scale numerical simulation can well characterize behaviors of asphalt materials and asphalt pavement, and the essential research progress is systematically summarized from an entire view. This paper reviews extensive research works concerning aspects of the design, characterization, and prediction of performance for asphalt materials and asphalt pavement based on multi-scale numerical simulation. Firstly, full-scale performance modeling on asphalt pavement is discussed from aspects of structural dynamic response, structural and material evaluation, and wheel–pavement interaction. The correlation between asphalt material properties and pavement performance is also analyzed, and so is the hydroplaning phenomenon. Macro- and mesoscale simulations on the mechanical property characterization of the asphalt mixture and its components are then investigated, while virtual proportion design for the asphalt mixture is introduced. Features of two-dimensional and three-dimensional microscale modeling on the asphalt mixture are summarized, followed by molecular dynamics simulation on asphalt binders, aggregates, and their interface, while nanoscale behavior modeling on asphalt binders is presented. Finally, aspects that need more attention concerning this study’s topic are discussed, and several suggestions for future investigations are also presented.
- Open Access
- 1 December 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (23) , 12291
Numerical Simulation and Experimental Measurements of Dynamic Responses of Asphalt Pavement in Dry and Saturated Conditions under Full-Scale Accelerated Loading
Asphalt pavement presents diverse dynamic responses to vehicle loading in dry and saturated conditions, which can be systematically explored by numerical simulation. Building a numerical model based on the actual conditions of asphalt pavement is necessary, and relevant field tests should be subsequently conducted to monitor dynamic responses to calibrate and validate the numerical model. On the basis of strictly controlling the paths of vehicle wheels during field tests, this study numerically analyzed the dynamic responses of asphalt pavement in dry and saturated conditions under full-scale accelerated loading. The trends of the modeling results were consistent with those of field measurements. The increase in vehicle load significantly increased the magnitudes of stress, strain, and pore water pressure, while vehicle speed showed an obvious impact on pore water pressure. The dynamic responses decreased with pavement depths. Water made the dynamic responses more complex, and pore water pressure significantly decreased with depth within the upper layer of saturated asphalt pavement. Transverse distributions of indicators presented obvious compressive states in the regions in direct contact with vehicle wheels, while tensile states were found in the range of the middle vehicle axle. The numerical results provided a basis for field measurements in future studies, especially for the exploration of factors of temperature and layer depth.
- 1 December 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (23) , 12291
Open AccessNumerical Simulation and Experimental Measurements of Dynamic Responses of Asphalt Pavement in Dry and Saturated Conditions under Full-Scale Accelerated Loading
Asphalt pavement presents diverse dynamic responses to vehicle loading in dry and saturated conditions, which can be systematically explored by numerical simulation. Building a numerical model based on the actual conditions of asphalt pavement is necessary, and relevant field tests should be subsequently conducted to monitor dynamic responses to calibrate and validate the numerical model. On the basis of strictly controlling the paths of vehicle wheels during field tests, this study numerically analyzed the dynamic responses of asphalt pavement in dry and saturated conditions under full-scale accelerated loading. The trends of the modeling results were consistent with those of field measurements. The increase in vehicle load significantly increased the magnitudes of stress, strain, and pore water pressure, while vehicle speed showed an obvious impact on pore water pressure. The dynamic responses decreased with pavement depths. Water made the dynamic responses more complex, and pore water pressure significantly decreased with depth within the upper layer of saturated asphalt pavement. Transverse distributions of indicators presented obvious compressive states in the regions in direct contact with vehicle wheels, while tensile states were found in the range of the middle vehicle axle. The numerical results provided a basis for field measurements in future studies, especially for the exploration of factors of temperature and layer depth.
- Open Access
The Effect of Microbiologically Induced Concrete Corrosion in Sewer on the Bearing Capacity of Reinforced Concrete Pipes: Full-Scale Experimental Investigation
The main part of sewer pipelines is commonly made up of precast reinforced concrete pipes (RCPs). However, they often suffer from microbiologically induced concrete corrosion (MICC), which has made them less durable than expected. In this study, three-edge bearing tests (TEBT) are performed on full-scale RCPs with preset wall losses to determine how MICC influences their bearing performance. For this purpose, several bearing indices such as D-load, peak load, ultimate load, ring deflection, ring stiffness, and failure energy are presented or specified to characterize the load-carrying capacity, stiffness, and toughness of these RCPs. It is found that crown concrete corrosion hardly changes the mechanical behavior of the first elastic zone of RCPs, so that D-load is not affected, but it shortens the crack propagation zone significantly, leading to a reduction in ultimate and peak loads. Furthermore, RCPs’ ring stiffness and toughness are negatively correlated to thickness of wall loss, while the transverse deformability of the ring cross-section is positively correlated with it. Additionally, it was found that crown corrosion affects the ultimate load of different sizes of RCP in different ways. The 2000 mm RCP is affected the most, with a 50 percent reduction in ultimate load. The 1000 mm RCP follows, with a 36 percent reduction, and the 1500 mm RCP has a reduction of less than 20 percent. This research contributes to comprehending the degradation of in-service sewage pipes, hence informing decision making on sewer maintenance and rehabilitation.
Open AccessThe Effect of Microbiologically Induced Concrete Corrosion in Sewer on the Bearing Capacity of Reinforced Concrete Pipes: Full-Scale Experimental Investigation
The main part of sewer pipelines is commonly made up of precast reinforced concrete pipes (RCPs). However, they often suffer from microbiologically induced concrete corrosion (MICC), which has made them less durable than expected. In this study, three-edge bearing tests (TEBT) are performed on full-scale RCPs with preset wall losses to determine how MICC influences their bearing performance. For this purpose, several bearing indices such as D-load, peak load, ultimate load, ring deflection, ring stiffness, and failure energy are presented or specified to characterize the load-carrying capacity, stiffness, and toughness of these RCPs. It is found that crown concrete corrosion hardly changes the mechanical behavior of the first elastic zone of RCPs, so that D-load is not affected, but it shortens the crack propagation zone significantly, leading to a reduction in ultimate and peak loads. Furthermore, RCPs’ ring stiffness and toughness are negatively correlated to thickness of wall loss, while the transverse deformability of the ring cross-section is positively correlated with it. Additionally, it was found that crown corrosion affects the ultimate load of different sizes of RCP in different ways. The 2000 mm RCP is affected the most, with a 50 percent reduction in ultimate load. The 1000 mm RCP follows, with a 36 percent reduction, and the 1500 mm RCP has a reduction of less than 20 percent. This research contributes to comprehending the degradation of in-service sewage pipes, hence informing decision making on sewer maintenance and rehabilitation.
- Open Access
Rheological Behaviors and Damage Mechanism of Asphalt Binder under the Erosion of Dynamic Pore Water Pressure Environment
Asphalt binder plays an important role in the overall resistance of asphalt mixture to the moisture damage induced by a dynamic pore water pressure environment. This study evaluates the moisture sensitivity of asphalt binder from the perspective of rheological behaviors using the dynamic shear rheometer (DSR) and the bending beam rheometer (BBR) methods at high, medium, and low temperatures. The damage mechanism is further discussed quantitatively based on the Fourier transform infrared spectroscopy (FTIR) method. The results indicate that a longer conditioning duration is beneficial for asphalt binder to recover its adhesion at 60 °C in multiple stress creep recover (MSCR) tests, but the increasing pore water pressure magnitude of 60 psi held an opposite effect in this study. The asphalt binder’s fatigue life at 20 °C in linear amplitude sweep (LAS) tests decreased obviously with conditioning duration and environmental severity, but the reducing rate gradually slowed down, while the groups of 50 psi—4000 cycles and 60 psi—4000 cycles held a comparable erosion effect. Both the stiffness and relaxation moduli at −12 °C in the BBR tests exhibited an obvious decreasing trend with conditioning duration and environmental severity. The erosion effect on the asphalt binder was gradually enhanced, but it also exhibited a slightly more viscous performance. Water conditioning induced several obvious characteristic peaks in the FTIR absorbance spectra of the asphalt binder. The functional group indexes presented a trend of non-monotonic change with conditioning duration and environmental severity, which made the asphalt binder show complicated rheological behaviors, such as non-monotonic variations in performance and the abnormal improving effect induced by dynamic pore water pressure conditioning.
Open AccessRheological Behaviors and Damage Mechanism of Asphalt Binder under the Erosion of Dynamic Pore Water Pressure Environment
Asphalt binder plays an important role in the overall resistance of asphalt mixture to the moisture damage induced by a dynamic pore water pressure environment. This study evaluates the moisture sensitivity of asphalt binder from the perspective of rheological behaviors using the dynamic shear rheometer (DSR) and the bending beam rheometer (BBR) methods at high, medium, and low temperatures. The damage mechanism is further discussed quantitatively based on the Fourier transform infrared spectroscopy (FTIR) method. The results indicate that a longer conditioning duration is beneficial for asphalt binder to recover its adhesion at 60 °C in multiple stress creep recover (MSCR) tests, but the increasing pore water pressure magnitude of 60 psi held an opposite effect in this study. The asphalt binder’s fatigue life at 20 °C in linear amplitude sweep (LAS) tests decreased obviously with conditioning duration and environmental severity, but the reducing rate gradually slowed down, while the groups of 50 psi—4000 cycles and 60 psi—4000 cycles held a comparable erosion effect. Both the stiffness and relaxation moduli at −12 °C in the BBR tests exhibited an obvious decreasing trend with conditioning duration and environmental severity. The erosion effect on the asphalt binder was gradually enhanced, but it also exhibited a slightly more viscous performance. Water conditioning induced several obvious characteristic peaks in the FTIR absorbance spectra of the asphalt binder. The functional group indexes presented a trend of non-monotonic change with conditioning duration and environmental severity, which made the asphalt binder show complicated rheological behaviors, such as non-monotonic variations in performance and the abnormal improving effect induced by dynamic pore water pressure conditioning.
- Open Access
Characterization of Rutting Damage by the Change of Air-Void Characteristics in the Asphalt Mixture Based on Two-Dimensional Image Analysis
In the process of the rutting test, the air-void characteristics in asphalt mixture specimens are a dynamic change process. It is of great significance to systematically study the correlation between the change of air-void characteristics and the depth of the rutting slab and establish a relationship with damage. In this paper, the air-void information of rutting specimen sections with different loading cycles (500, 1000, 1500, 2000, 2500, and 3000 times) is obtained by two-dimensional image technology. The dynamic change process of the micro characteristics of internal air voids of two graded asphalt mixtures (AC-13 and AC-16) under cyclic wheel load is analyzed, and it is used as an index to characterize the microstructure damage of the asphalt mixture. The results show that the variation of air-void distribution, air-void shape characteristics, and air-void fractal dimension with the loading process can well characterize the permanent deformation law of the rutting slab. The fractal dimension of the air void increases with the increase in load. It is a dynamic process in which the air-void content changes with crack initiation and propagation. After rutting deformation, the total air-void area and average air-void size of the sample increase, and the total air-void number decreases. Because microcracks are formed in the specimen after rutting damage, the aspect ratio of the air void increases, and the roundness value decreases.
Open AccessCharacterization of Rutting Damage by the Change of Air-Void Characteristics in the Asphalt Mixture Based on Two-Dimensional Image Analysis
In the process of the rutting test, the air-void characteristics in asphalt mixture specimens are a dynamic change process. It is of great significance to systematically study the correlation between the change of air-void characteristics and the depth of the rutting slab and establish a relationship with damage. In this paper, the air-void information of rutting specimen sections with different loading cycles (500, 1000, 1500, 2000, 2500, and 3000 times) is obtained by two-dimensional image technology. The dynamic change process of the micro characteristics of internal air voids of two graded asphalt mixtures (AC-13 and AC-16) under cyclic wheel load is analyzed, and it is used as an index to characterize the microstructure damage of the asphalt mixture. The results show that the variation of air-void distribution, air-void shape characteristics, and air-void fractal dimension with the loading process can well characterize the permanent deformation law of the rutting slab. The fractal dimension of the air void increases with the increase in load. It is a dynamic process in which the air-void content changes with crack initiation and propagation. After rutting deformation, the total air-void area and average air-void size of the sample increase, and the total air-void number decreases. Because microcracks are formed in the specimen after rutting damage, the aspect ratio of the air void increases, and the roundness value decreases.
- Open Access
- 13 September 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (18) , 8505
Acoustic Emission Wave Velocity Measurement of Asphalt Mixture by Arbitrary Wave Method
The wave velocity of acoustic emission (AE) can reflect the properties of materials, the types of AE sources and the propagation characteristics of AE in materials. At the same time, the wave velocity of AE is also an important parameter in source location calculation by the time-difference method. In this paper, a new AE wave velocity measurement method, the arbitrary wave (AW) method, is proposed and designed to measure the AE wave velocity of an asphalt mixture. This method is compared with the pencil lead break (PLB) method and the automatic sensor test (AST) method. Through comparison and analysis, as a new wave velocity measurement method of AE, the AW method shows the following advantages: A continuous AE signal with small attenuation, no crosstalk and a fixed waveform can be obtained by the AW method, which is more advantageous to distinguish the first arrival time of the acoustic wave and calculate the wave velocity of AE more accurately; the AE signal measured by the AW method has the characteristics of a high frequency and large amplitude, which is easy to distinguish from the noise signal with the characteristics of a low frequency and small amplitude; and the dispersion of the AE wave velocity measured by the AW method is smaller, which is more suitable for the measurement of the AE wave velocity of an asphalt mixture.
- 13 September 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (18) , 8505
Open AccessAcoustic Emission Wave Velocity Measurement of Asphalt Mixture by Arbitrary Wave Method
The wave velocity of acoustic emission (AE) can reflect the properties of materials, the types of AE sources and the propagation characteristics of AE in materials. At the same time, the wave velocity of AE is also an important parameter in source location calculation by the time-difference method. In this paper, a new AE wave velocity measurement method, the arbitrary wave (AW) method, is proposed and designed to measure the AE wave velocity of an asphalt mixture. This method is compared with the pencil lead break (PLB) method and the automatic sensor test (AST) method. Through comparison and analysis, as a new wave velocity measurement method of AE, the AW method shows the following advantages: A continuous AE signal with small attenuation, no crosstalk and a fixed waveform can be obtained by the AW method, which is more advantageous to distinguish the first arrival time of the acoustic wave and calculate the wave velocity of AE more accurately; the AE signal measured by the AW method has the characteristics of a high frequency and large amplitude, which is easy to distinguish from the noise signal with the characteristics of a low frequency and small amplitude; and the dispersion of the AE wave velocity measured by the AW method is smaller, which is more suitable for the measurement of the AE wave velocity of an asphalt mixture.