Marcel Krochmal
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Marcel Krochmal has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
- Thomas Niendorf
Institute of Materials Engineering, Universität Kassel, Kassel, Germany
11 shared publications - Thomas Wegener
University of Kassel, Institute of Materials Engineering – Metallic Materials Kassel Germany
9 shared publications - Alexander Hartmaier
Ruhr University Bochum
4 shared publications - Aravindh Nammalvar Raja Rajan
Institute of Mechanical Engineering, Westphalian University of Applied Sciences, Gelsenkirchen, Germany
4 shared publications T. Niendorf
4 shared publicationsT. Wegener
3 shared publications
Latest Publications
- Open Access
- 24 October 2026
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 979
Low-cycle fatigue behavior of friction stir welded joint of additively manufactured and cast AlSi10Mg: A combined experimental and multiscale modeling approach
- 24 October 2026
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 979
Open AccessLow-cycle fatigue behavior of friction stir welded joint of additively manufactured and cast AlSi10Mg: A combined experimental and multiscale modeling approach
- Open Access
- 26 May 2026
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 42, 12042-12056
Microstructural evolution and fatigue response of friction stir welded hybrid aluminum joints after T6 heat treatment
- 26 May 2026
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 42, 12042-12056
Open AccessMicrostructural evolution and fatigue response of friction stir welded hybrid aluminum joints after T6 heat treatment
- Open Access
- 23 April 2026
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 49 (7) , 2767-2779
Fatigue Strength Analysis of a Cladded Steel Subjected to Tensile Predeformation
Cladded steels are a subset of layered metal composites in which a thin functional layer is bonded to a dissimilar substrate, thereby integrating the benefits of both constituent materials. However, the resulting heterogeneous properties of such layered metal composites collectively complicate deformation and fatigue behavior, making reliable prediction challenging. The present study demonstrates that the local fatigue strength concept can be applied to layered metal composites as a complementary method that can support fatigue analysis. The concept was used to analyze both as‐received and predeformed material, with the latter exhibiting reduced fatigue strength. For the as‐received condition, predicted crack initiation sites agree well with experimental observations. For a predeformed condition, predictions are less accurate, which was attributed to the model underestimating the influence of surface residual stress and surface topography. These findings indicate that existing fatigue frameworks can be readily applied to layered metal composites with only limited modifications.
- 23 April 2026
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 49 (7) , 2767-2779
Open AccessFatigue Strength Analysis of a Cladded Steel Subjected to Tensile Predeformation
Cladded steels are a subset of layered metal composites in which a thin functional layer is bonded to a dissimilar substrate, thereby integrating the benefits of both constituent materials. However, the resulting heterogeneous properties of such layered metal composites collectively complicate deformation and fatigue behavior, making reliable prediction challenging. The present study demonstrates that the local fatigue strength concept can be applied to layered metal composites as a complementary method that can support fatigue analysis. The concept was used to analyze both as‐received and predeformed material, with the latter exhibiting reduced fatigue strength. For the as‐received condition, predicted crack initiation sites agree well with experimental observations. For a predeformed condition, predictions are less accurate, which was attributed to the model underestimating the influence of surface residual stress and surface topography. These findings indicate that existing fatigue frameworks can be readily applied to layered metal composites with only limited modifications.
- Open Access
- 17 January 2025
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 56 (3) , 765-770
On the Changes of Residual Stress States of S550MC + 100Cr6 Cladded Steel Upon Tensile Deformation
The present study focuses on the evolution of residual stress (RS) and internal damage of a S550MC + 100Cr6 cladded steel after pre-deformation. Deformation-induced internal porosity was hardly found. RS depth profiles point at tensile RS in the 100Cr6 clad layer. These are most pronounced when minor pre-deformation levels are considered. A higher degree of deformation leads to reduced magnitudes of RS. This can be rationalized based on reduced differences in layer strength due to local strain hardening.
- 17 January 2025
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 56 (3) , 765-770
Open AccessOn the Changes of Residual Stress States of S550MC + 100Cr6 Cladded Steel Upon Tensile Deformation
The present study focuses on the evolution of residual stress (RS) and internal damage of a S550MC + 100Cr6 cladded steel after pre-deformation. Deformation-induced internal porosity was hardly found. RS depth profiles point at tensile RS in the 100Cr6 clad layer. These are most pronounced when minor pre-deformation levels are considered. A higher degree of deformation leads to reduced magnitudes of RS. This can be rationalized based on reduced differences in layer strength due to local strain hardening.
- Open Access
- 1 August 2024
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 47 (10) , 3707-3722
Impact of a single‐side 100Cr6 clad layer on the tensile and fatigue properties of S550MC steel
The production of newly developed hot‐rolled layered metal composites (LMC) leads to the availability of sheet materials with specifically adjustable, graded properties being cost‐effective and suitable for large‐scale production. As many of the envisaged applications of these LMC, e.g., clutch disc carriers, suffer from cyclic loading during service life, a fundamental knowledge of the fatigue behavior is required in order to ensure safe and reliable application of the components. Therefore, the present study focuses on the fatigue behavior of a hot‐rolled two‐layer LMC consisting of a S550MC substrate layer and a 100Cr6 clad layer. In order to investigate the influence of the clad layer, two conditions are directly compared, i.e., the two‐layer laminate cladded steel and the single‐layer substrate condition. Results presented by mechanical testing include hardness measurements and tensile tests as well as strain‐controlled low‐cycle fatigue and stress‐controlled high‐cycle fatigue tests. These results are discussed based on evolution of microstructure, residual stress, and defects, respectively, as elaborated by scanning electron microscopy, X‐ray diffraction, and fracture surface analysis.
- 1 August 2024
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 47 (10) , 3707-3722
Open AccessImpact of a single‐side 100Cr6 clad layer on the tensile and fatigue properties of S550MC steel
The production of newly developed hot‐rolled layered metal composites (LMC) leads to the availability of sheet materials with specifically adjustable, graded properties being cost‐effective and suitable for large‐scale production. As many of the envisaged applications of these LMC, e.g., clutch disc carriers, suffer from cyclic loading during service life, a fundamental knowledge of the fatigue behavior is required in order to ensure safe and reliable application of the components. Therefore, the present study focuses on the fatigue behavior of a hot‐rolled two‐layer LMC consisting of a S550MC substrate layer and a 100Cr6 clad layer. In order to investigate the influence of the clad layer, two conditions are directly compared, i.e., the two‐layer laminate cladded steel and the single‐layer substrate condition. Results presented by mechanical testing include hardness measurements and tensile tests as well as strain‐controlled low‐cycle fatigue and stress‐controlled high‐cycle fatigue tests. These results are discussed based on evolution of microstructure, residual stress, and defects, respectively, as elaborated by scanning electron microscopy, X‐ray diffraction, and fracture surface analysis.
- Open Access
- 29 April 2024
- Published by Springer Nature in Welding in the World
- Vol. 68 (7) , 1693-1705
Micro-macro modeling of tensile behavior of a friction stir welded hybrid joint of AlSi10Mg parts produced by powder bed fusion and casting
Additive manufacturing (AM) has gained considerable interest due to its ability to produce lightweight parts with hierarchical microstructures. However, the current constraints on the build chamber size in powder-bed fusion type AM processes limit its industrial application. A hybrid welded joint, consisting of an AM-processed and a conventionally manufactured part, can be employed to produce larger components. Due to the varying processing conditions, these hybrid welded joints contain a wide range of microstructural heterogeneities, which influences the mechanical properties of the joint. Using a numerical model to predict the mechanical behavior of welded joints by considering the microstructural variations is essential for the safe and reliable implementation of hybrid welded joints. This study aims to predict the local tensile behavior of each region of a hybrid friction-stir welded joint of AlSi10Mg produced by laser-based powder bed fusion and casting using a microstructure-sensitive model as well as the global tensile behavior by considering the properties of each region using a joint macroscopic model. The results from this modeling approach agree well with the experimental results. Therefore, this method can predict the mechanical behavior of hybrid welded joints and can establish the structure–property relationship in each weld region.
- 29 April 2024
- Published by Springer Nature in Welding in the World
- Vol. 68 (7) , 1693-1705
Open AccessMicro-macro modeling of tensile behavior of a friction stir welded hybrid joint of AlSi10Mg parts produced by powder bed fusion and casting
Additive manufacturing (AM) has gained considerable interest due to its ability to produce lightweight parts with hierarchical microstructures. However, the current constraints on the build chamber size in powder-bed fusion type AM processes limit its industrial application. A hybrid welded joint, consisting of an AM-processed and a conventionally manufactured part, can be employed to produce larger components. Due to the varying processing conditions, these hybrid welded joints contain a wide range of microstructural heterogeneities, which influences the mechanical properties of the joint. Using a numerical model to predict the mechanical behavior of welded joints by considering the microstructural variations is essential for the safe and reliable implementation of hybrid welded joints. This study aims to predict the local tensile behavior of each region of a hybrid friction-stir welded joint of AlSi10Mg produced by laser-based powder bed fusion and casting using a microstructure-sensitive model as well as the global tensile behavior by considering the properties of each region using a joint macroscopic model. The results from this modeling approach agree well with the experimental results. Therefore, this method can predict the mechanical behavior of hybrid welded joints and can establish the structure–property relationship in each weld region.
- 15 June 2023
- Published by Elsevier in International Journal of Fatigue
- Vol. 175
On the low-cycle fatigue behavior of a novel high-strength mold steel
- 15 June 2023
- Published by Elsevier in International Journal of Fatigue
- Vol. 175
On the low-cycle fatigue behavior of a novel high-strength mold steel
- 3 June 2023
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 879
Micromechanical modeling of the low-cycle fatigue behavior of additively manufactured AlSi10Mg
- 3 June 2023
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 879
Micromechanical modeling of the low-cycle fatigue behavior of additively manufactured AlSi10Mg
- Open Access
- 7 December 2022
- Published by Springer Nature in Journal of Materials Research
- Vol. 38 (2) , 297-311
Microstructural and mechanical properties of AlSi10Mg: Hybrid welding of additively manufactured and cast parts
Welding and joining of hybrid components consisting of additively manufactured (AM) parts and conventionally processed parts offer new opportunities in structural design. In the present study, AlSi10Mg specimens were fabricated using two different manufacturing processes, i.e., laser-based powder-bed fusion of metals (PBF-LB/M) and casting, and welded by means of friction stir welding (FSW). Material strength of dissimilar welded joints was found to be governed by the as-cast material, which is characterized by a very coarse microstructure resulting in inferior hardness and tensile properties. During fatigue testing, cast-cast specimens performed slightly better than their hybrid AM-cast counterparts with respect to lifetime, being rationalized by most pronounced strain inhomogeneities in the AM-cast specimens. With the aim of cost reduction, FSW can be employed to fabricate graded large parts as long as the AM as-built material is placed in the region demanding superior cyclic load-bearing capacity.Graphical abstract
- 7 December 2022
- Published by Springer Nature in Journal of Materials Research
- Vol. 38 (2) , 297-311
Open AccessMicrostructural and mechanical properties of AlSi10Mg: Hybrid welding of additively manufactured and cast parts
Welding and joining of hybrid components consisting of additively manufactured (AM) parts and conventionally processed parts offer new opportunities in structural design. In the present study, AlSi10Mg specimens were fabricated using two different manufacturing processes, i.e., laser-based powder-bed fusion of metals (PBF-LB/M) and casting, and welded by means of friction stir welding (FSW). Material strength of dissimilar welded joints was found to be governed by the as-cast material, which is characterized by a very coarse microstructure resulting in inferior hardness and tensile properties. During fatigue testing, cast-cast specimens performed slightly better than their hybrid AM-cast counterparts with respect to lifetime, being rationalized by most pronounced strain inhomogeneities in the AM-cast specimens. With the aim of cost reduction, FSW can be employed to fabricate graded large parts as long as the AM as-built material is placed in the region demanding superior cyclic load-bearing capacity.Graphical abstract