Dodda Srinivas
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Dodda Srinivas has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Biranchi Panda
Indian Institute of Technology Guwahati
3 shared publications - Sitharam Tg
IISc, Bengaluru, Bengaluru, India
3 shared publications Biranchi Panda
2 shared publications- Dhrutiman Dey
Indian Institute of Technology Guwahati
2 shared publications - Dhrutiman Dey
Indian Institute of Technology Guwahati
2 shared publications Prannoy Suraneni
2 shared publications
Latest Publications
- 27 January 2025
- Published by Elsevier in Journal of Cleaner Production
- Vol. 492
Influence of mixture composition and carbonation curing on properties of sustainable 3D printable mortars
- 27 January 2025
- Published by Elsevier in Journal of Cleaner Production
- Vol. 492
Influence of mixture composition and carbonation curing on properties of sustainable 3D printable mortars
- 14 September 2024
- Published by Springer Nature
- p. 51-61
Development of Outdoor Furniture Using 3D Concrete Printing
- 14 September 2024
- Published by Springer Nature
- p. 51-61
Development of Outdoor Furniture Using 3D Concrete Printing
- Open Access
Printability, Thermal and Compressive Strength Properties of Cementitious Materials: A Comparative Study with Silica Fume and Limestone
Over the past decade, 3D printing in the construction industry has received worldwide attention and developed rapidly. The research and development of cement and concrete products has also become quite well-established over the years, while other sustainable materials receive considerably lower attention in comparison. This study aims to investigate the influence of the two most commonly used sustainable cementitious materials i.e., silica fume and limestone powder, on printability, thermal and mechanical properties of fly ash–Portland cement blends. Ternary blends containing Portland cement, fly ash and silica fume or limestone powder are prepared, whereas phase change material (PCM) is introduced to improve the thermal behavior. Based on the rheological properties and concurrent 3D concrete printing, improved buildability of the modified mixtures is linked to their static yield stress. Anisotropic mechanical properties are observed for 3D printed specimens, while cast specimens exhibit a maximum 41% higher compressive strength due to better material compaction. It is clear from the results that addition of silica fume and limestone powder ranged from 5% to 10%, reducing the anisotropic mechanical properties (maximum 71% and 68% reduction in anisotropic factor, respectively) in the printed specimens. The PCM addition ranged from 5% to 10% and improved thermal performance of the mixtures, as measured by a decrease in thermal conductivity (9% and 13%) and an increase in volumetric heat capacity (9% and 10%), respectively. However, the PCM-containing mixtures show around 29% reduction in compressive strength, compared to the control specimen, which necessitates new material design considering matrix strengthening methods.
Open AccessPrintability, Thermal and Compressive Strength Properties of Cementitious Materials: A Comparative Study with Silica Fume and Limestone
Over the past decade, 3D printing in the construction industry has received worldwide attention and developed rapidly. The research and development of cement and concrete products has also become quite well-established over the years, while other sustainable materials receive considerably lower attention in comparison. This study aims to investigate the influence of the two most commonly used sustainable cementitious materials i.e., silica fume and limestone powder, on printability, thermal and mechanical properties of fly ash–Portland cement blends. Ternary blends containing Portland cement, fly ash and silica fume or limestone powder are prepared, whereas phase change material (PCM) is introduced to improve the thermal behavior. Based on the rheological properties and concurrent 3D concrete printing, improved buildability of the modified mixtures is linked to their static yield stress. Anisotropic mechanical properties are observed for 3D printed specimens, while cast specimens exhibit a maximum 41% higher compressive strength due to better material compaction. It is clear from the results that addition of silica fume and limestone powder ranged from 5% to 10%, reducing the anisotropic mechanical properties (maximum 71% and 68% reduction in anisotropic factor, respectively) in the printed specimens. The PCM addition ranged from 5% to 10% and improved thermal performance of the mixtures, as measured by a decrease in thermal conductivity (9% and 13%) and an increase in volumetric heat capacity (9% and 10%), respectively. However, the PCM-containing mixtures show around 29% reduction in compressive strength, compared to the control specimen, which necessitates new material design considering matrix strengthening methods.
- 24 July 2022
- Published by Springer Nature
- p. 283-291
Processing of Cementitious Materials for 3D Concrete Printing
- 24 July 2022
- Published by Springer Nature
- p. 283-291
Processing of Cementitious Materials for 3D Concrete Printing
- Top Cited Papers
- 4 February 2022
- Published by Elsevier in Journal of Cleaner Production
- Vol. 340
Use of industrial waste materials for 3D printing of sustainable concrete: A review
- 4 February 2022
- Published by Elsevier in Journal of Cleaner Production
- Vol. 340
Top Cited PapersUse of industrial waste materials for 3D printing of sustainable concrete: A review