DSDhananjay Kumar Srivastava

Dhananjay Kumar Srivastava

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Dhananjay Kumar Srivastava has a total of 19 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Large eddy simulation of flow separation-induced disturbance evolution inside a sudden contracting nozzle

    by Jagannath Mahato, Toshan Lal Sahu, Ujjwal Chetan, Prabir Kumar Kar, Dhananjay Kumar Srivastava, Rajaram Lakkaraju


  • A comprehensive mathematical theory and optimized design of a high-frequency electro-pneumatic variable valve actuator for a camless IC engine

    by Ajay Kumar Satalagaon, Abhijit Guha, Dhananjay Kumar Srivastava

    This paper discusses the development of a detailed mathematical theory and its use for the design of an electronically controlled, double-acting Variable Valve Actuation (VVA) mechanism for a camless internal combustion engine, that offers a comprehensive control over the timings and the motion of the valves such that any arbitrary time-variation of the valve lift profile can be obtained at variable rotational speeds of the engine shaft. The developed theory encompasses the thermo-fluid-dynamic as well as the applied-mechanical aspects of the actuator cylinder-engine valve system performance, the dynamics of the valve actuation being characterized by parameters such as valve opening duration, peak lift and seating velocity. The prediction of the mathematical theory compares well with several experimental data sets obtained from an in-house pneumatic VVA set-up. A new design methodology is formulated for determining the appropriate dimensions of the actuator, operating thermodynamic parameters and the electronic control of the various valve events for a desired range of engine rotational speed. Several parameters in the new design philosophy are kept within acceptable ranges established from time-tested data obtained from conventional cam-based valve actuation. For example, a new pneumatic cushioning strategy has been developed that is simple, effective and energy-efficient, and is able to keep the valve seating velocity within an acceptable range (0.08–1.13 m/s). The work also discusses the implementation of several constraints that are necessary for the design of a practically viable pneumatic actuator. The evolution of a design matrix map for the electro-pneumatic VVA is quantified for the engine rotational speed varying up to 5500 rpm.


  • Experimental Study of Effect of Injection Timing on Port Fuel Injection Gasoline, Port Fuel Injection Compressed Natural Gas, and Direct Injection Compressed Natural Gas Engine Performance, Combustion, and Emissions Characteristics

    by Sridhar Sahoo, Dhananjay Kumar Srivastava

    Compressed natural gas (CNG) has gained popularity due to its wide availability, higher efficiency, and lower emissions compared to gasoline. However, the lower flame speed characteristics of CNG with conventional port injection reduce the CNG engine volumetric efficiency and power output. CNG's lower gas jet momentum during a low load operation creates a non-uniform air-fuel mixture that affects ignition and combustion quality. Direct injection of CNG with optimum injection timing is expected to improve volumetric efficiency, ignition quality, and combustion process. In this study, a comparative study on the effect of end-of-injection (EOI) timing on volumetric efficiency, thermal efficiency, combustion duration, and emissions was carried out in a single-cylinder port fuel injection (PFI) spark-ignition engine using gasoline and CNG, and direct injection (DI) spark ignition engine using CNG. The experiments were performed at two-part load operations of 20% and 40% throttle at 900 and 1500 rpm. Experimental results indicate that the PFI CNG engine is more influential in EOI timing than gasoline engines. The performance of the PFI CNG engine is improved when the injection occurs during the intake valve open period compared to the closed valve period with higher thermal efficiency, volumetric efficiency, and indicated mean effective power (IMEP). A shorter flame development angle and combustion duration were observed when EOI timing was in the open intake valve condition. DI CNG improved volumetric efficiency at advanced EOI timing compared to the PFI CNG engine. However, the combustion process is critically dependent on injection timing and air-fuel mixing duration. A three-dimensional computational fluid dynamics simulation was conducted to evaluate the effect of advanced and retarded EOI timing on DI CNG engine's in-cylinder turbulent kinetic energy development and in-cylinder equivalence ratio near the ignition point. An excess advanced EOI timing resulted in stratified rich and retarded EOI timing results in loss of turbulence energy, leading to a slightly rich and lean mixture for advanced and retarded EOI timing, respectively. Hence, an optimum EOI timing provides a conducive environment to initiate the combustion and flame front propagation. Further, advanced EOI timing was required at higher throttle opening and engine speed. The emissions in DI CNG were also greatly affected by EOI timing.


  • A Numerical Study on Spray Combustion and Emissions Characteristics of n-Heptane, Dimethyl Ether, and Their Blends in a Constant Volume Combustion Chamber

    by Balram Sahu, Dhananjay Kumar Srivastava

    Dimethyl ether appears to be a better choice among various diesel alternatives due to its high cetane number and sootless combustion. However, the physical and chemical properties of dimethyl ether are very different from those of diesel. The physical properties influence spray formation and atomization characteristics, while chemical properties determine combustion and emission formation characteristics. Thus, fuel's physical and chemical properties significantly determine engine performance and emissions. In the present work, spray combustion and emission formation characteristics of n-heptane, dimethyl ether, and their blends (10, 25, and 50% dimethyl ether in n-heptane) were numerically studied in a constant volume chamber. Results show that the n-heptane spray combustion has the highest heat release rate with an intense premix combustion phase, whereas dimethyl ether spray combustion has the lowest heat release rate and shortest premix combustion phase. The magnitude of the premixed phase and heat release rate decreases with the increase in dimethyl ether mass fraction in the blends. Soot, carbon monoxide (CO), unburned hydrocarbon (UHC), and nitric oxide (NO) emissions decreased with the increase in the dimethyl ether mass fraction in the blends and were lowest for the dimethyl ether.


  • A numerical investigation of injector hole configuration and injection parameters in a dimethyl ether fueled DICI engine

    by Balram Sahu, Dhananjay Kumar Srivastava

    The lower calorific value of dimethyl ether (DME) is approximately 65% of that of diesel; therefore, a higher quantity of DME must be supplied per cycle to generate the same magnitude of power. A retrofitted DME‐fueled engine generally uses a longer fuel injection duration to provide the excess fuel mass. The present work seeks to find the most appropriate way to increase the mass flow rate of a DME‐fueled direct‐injected compression ignition engine by varying the number of nozzle holes, nozzle hole diameter, and injection pressure. The results show that increasing mass flow rate increases peak combustion pressure and heat release rate but decreases combustion duration. Increasing the number of injector holes increases indicated specific fuel consumption (ISFC) and exhaust emissions (NOx, HC, and CO) due to mixing between unburned fuel spray and neighboring combustion products. Increasing the nozzle hole diameter or fuel injection pressure increases spray tip penetration and improves fuel‐air mixing before combustion initiates. Increasing the nozzle hole diameter by merely 22 μm than the baseline injector reduces ISFC and exhaust emissions at a slightly retarded start of injection (SOI). However, the lowest ISFC was found at the 30 MPa injection pressure at the most advanced SOI, at the expense of higher NOx.


  • A comparative assessment of performance, combustion, and emissions of a gasoline port and direct injection camless engine

    by Srinibas Tripathy, Dhananjay Kumar Srivastava

    The lower part‐load efficiency of the spark‐ignition (SI) engine is because of the higher pumping loss during the gas exchange process. In this study, the part‐load efficiency of a port fuel injection (PFI) and gasoline direct injection (GDI) camless engines were investigated. An in‐house developed electro‐pneumatic variable valve actuation (VVA) system controls the camless engine's intake valve events. The effect of un‐throttled operation with early intake valve closings (EIVC) on performance, combustion, and emissions was analyzed. The IVC timing for GDI camless engine was found to be lower (2°–7° crank angle) than the PFI camless engine for all operating conditions due to the in‐cylinder charge cooling. Hence, the pumping mean effective pressure (PMEP) for GDI camless engine was reduced, and brake specific fuel consumption (BSFC) was improved (maximum 2.1%) compared to the PFI camless engine. The THC and CO emissions were higher for GDI camless engine due to the relatively in‐homogeneous mixture formation, whereas the NOx emission was lower for all operating conditions.


  • Effect of internal exhaust gas recirculation on performance, combustion, and emissions in a PFI camless engine

    by Srinibas Tripathy, Dhananjay Kumar Srivastava

    The internal exhaust gas recirculation (EGR) into the intake manifold has a significant impact on fuel economy and emissions in the spark ignition (SI) engine. In this study, an in‐house developed novel electro‐pneumatic variable valve actuation (VVA) system was integrated on a PFI conventional engine and modified into PFI camless engine to vary the valve events independently. The potential of the developed VVA system in achieving the internal EGR by varying the intake valve opening (IVO) timings was widely investigated. The IVO timing was varied from 30° CA (crank angle) bITDC (before intake top dead center) to 40° CA aITDC (after intake top dead center). The spark timing was varied from 10° to 30° CA bCTDC (before compression top dead center). A 41% pumping mean effective pressure reduction was achieved with varying the IVO from 40° to −30° CA aITDC. It is due to the internal exhaust gas recirculation into the intake manifold that reduces the differential pressure between the manifold and combustion chamber. The entrapment of exhaust gas in the intake manifold dilutes the fresh charge, which deteriorates the combustion. However, advancing the spark timing from 10° to 30° CA bCTDC at IVO −30° CA aITDC, an 18% gas excahnge efficiency improvement was obtained. The fresh charge dilution forms an inhomogeneous mixture inside the cylinder that results in lower NOx emission. It is concluded that the developed VVA system has the potential to improve part loads efficiency by utilizing the internal EGR in a PFI camless engine.


  • On Offset Placement of a Compound Droplet in a Channel Flow

    by Jagannath Mahato, Dhananjay Kumar Srivastava, Dinesh Kumar Chandraker, Rajaram Lakkaraju

    We have investigated the dynamics of a simple and a compound droplet separately passing through a two-dimensional Poiseuille channel flow by using the volume-of-fluids method under low Reynolds numbers (Re=1). A simple droplet while passing through the channel shows an elongation in shape in the streamwise direction and compression in the transverse direction. A round symmetric droplet evolves into a pear-like shape with time, if it is released at an off-centre to the channel mid-line. If a compound droplet (which consists of a thin shell separating an inner fluid zone from an outer fluid zone) is released in the channel either at the mid-line or with an offset, we observed the round shape evolves into a slipper-like shape. The inner droplet breaks away from the outer one within a short period. A detailed study of droplet deformation and its breakup has been carried out for different fluid properties and the compound droplet size ratios, and we found the lateral migration is high for the compound droplets when compared to the simple droplets. We also observed that the break time of the compound droplet decreases with the increase in the offset release location exponentially.


  • Effect of injection timing on combustion and IMEP variation of a bi‐fuel compressed natural gas SI engine

    by Sridhar Sahoo, Dhananjay Kumar Srivastava

    Compressed natural gas (CNG) is a gaseous fuel stored under high pressure in a cylindrical tank. When the CNG is injected into the intake manifold, it expands in the manifold and displaces the air which reduces the volumetric efficiency of the engine. Thus, the corresponding overall energy inside the combustion chamber is also reduced, resulting in reduced power output. CNG injection timing with respect to intake valve opening and closing can be optimized to minimize the losses in volumetric efficiency loss and hence, the power output of the engine. In this study, the combustion instability of the CNG fueled engine has been studied under low throttle condition and compared with gasoline. A comparative investigation of the effects of the start of injection (SOI) timing on combustion stability was conducted on a single‐cylinder spark‐ignition (SI) engine fuelled with gasoline and CNG at 25% throttle opening condition. The ignition timing was kept fixed at 35°, and 40° CA bTDC for gasoline and CNG, respectively, and the SOI timing was varied from 240° CA bTDC to 100° CA aTDC of the intake stroke. The results indicated that SOI timing significantly affects in‐cylinder air‐fuel mixture formation and combustion stability for gasoline and CNG engine. SOI timing corresponds to the closed valve period, shows the higher fluctuation in combustion for gasoline compared to CNG. CNG shows lower fluctuation throughout SOI timing due to homogeneous air‐fuel mixture formation. Early SOI timing forms fuel stratification in the intake port and forms a rich air‐fuel mixture, which reduces the net power output of the CNG engine. CNG requires optimum SOI timing for improved combustion compared to gasoline. It reduced the combustion instability and fluctuation in indicated mean effective pressure. The results will benefit the development of a closed‐loop engine control system for a CNG system.