B. S. Keerthi Gowda
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
B. S. Keerthi Gowda has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
R. Velmurugan
IIT Madrs
7 shared publicationsG.L. Easwara Prasad
3 shared publications- G. L. Easwara Prasad
Manglore Institute of Technology and Engineering
2 shared publications A.P. Abhishek
1 shared publicationD. C. Naveen
Department of Civil Engineering
1 shared publication- Durga Prasad Channabasavaiah
Department of Mechanical Engineering, RV Institute of Technology and Management, Bengaluru, India
1 shared publication
Latest Publications
- 18 May 2024
- Published by Springer Nature
- p. 293-302
A Review on Different Processing Methods to Improve Pozzolanic Properties of Agricultural Waste Ashes
- 18 May 2024
- Published by Springer Nature
- p. 293-302
A Review on Different Processing Methods to Improve Pozzolanic Properties of Agricultural Waste Ashes
- RetractedOpen Access
- 8 November 2022
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2022, 1-11
Effects of Polypropylene Waste Addition as Coarse Aggregates in Concrete: Experimental Characterization and Statistical Analysis
In recent times, thermoplastic waste materials are being extensively used as fine and coarse aggregates in the concrete mix as an environmentally friendly construction material. This study aims at utilizing polypropylene (PP) as a partial substitute for the conventional coarse aggregates in M30 grade concrete. The different replacement levels of coarse aggregates such as 0%, 20%, 40%, and 60% by weight were used in concrete. Sieve analysis, specific gravity, and water absorption tests were performed in all replacement levels of aggregates. The mechanical (compressive and split tensile tests) tests were conducted after 3, 14, and 28 days. The change in mechanical properties of concrete with the addition of different weight proportions of plastics was studied experimentally. Further, experimental values were predicted using the two-parameter Weibull distribution and artificial neural network (ANN)-based statistical approaches. The Levenberg–Marquardt algorithm was used in predicting the mechanical properties using the ANN. A good correlation was obtained between the experimental and predicted values with an error (%) of less than 10. The decrease in mechanical properties with the increase in replacement levels of coarse aggregates in concrete was observed in both experimental and predicted approaches. This can be attributed to poor bonding between concrete and PP aggregate owing to the development of agglomerations and the hydrophobic nature of PP. However, the strength values of 20% PP-embedded concrete specimens are closer to 0% PP-embedded concrete specimens. Therefore, 20% PP-embedded concrete specimens can be used for primary load-bearing applications to utilize plastic waste and reduce the cost of the component.
- 8 November 2022
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2022, 1-11
RetractedOpen AccessEffects of Polypropylene Waste Addition as Coarse Aggregates in Concrete: Experimental Characterization and Statistical Analysis
In recent times, thermoplastic waste materials are being extensively used as fine and coarse aggregates in the concrete mix as an environmentally friendly construction material. This study aims at utilizing polypropylene (PP) as a partial substitute for the conventional coarse aggregates in M30 grade concrete. The different replacement levels of coarse aggregates such as 0%, 20%, 40%, and 60% by weight were used in concrete. Sieve analysis, specific gravity, and water absorption tests were performed in all replacement levels of aggregates. The mechanical (compressive and split tensile tests) tests were conducted after 3, 14, and 28 days. The change in mechanical properties of concrete with the addition of different weight proportions of plastics was studied experimentally. Further, experimental values were predicted using the two-parameter Weibull distribution and artificial neural network (ANN)-based statistical approaches. The Levenberg–Marquardt algorithm was used in predicting the mechanical properties using the ANN. A good correlation was obtained between the experimental and predicted values with an error (%) of less than 10. The decrease in mechanical properties with the increase in replacement levels of coarse aggregates in concrete was observed in both experimental and predicted approaches. This can be attributed to poor bonding between concrete and PP aggregate owing to the development of agglomerations and the hydrophobic nature of PP. However, the strength values of 20% PP-embedded concrete specimens are closer to 0% PP-embedded concrete specimens. Therefore, 20% PP-embedded concrete specimens can be used for primary load-bearing applications to utilize plastic waste and reduce the cost of the component.
- 11 April 2021
- Published by Taylor & Francis in Journal of Natural Fibers
- Vol. 19 (13) , 6074-6088
Effect of Fiber Volume Fraction on Mechanical and Fire Resistance Properties of Basalt/Polyester and Pineapple/Polyester Composites
In general, the wood materials are used for constructing the buildings, passenger seats in trains and automobile doors. However, the progression of the fires due to the wooden construction is high when the fire accidents have occurred in the buildings, rail and road vehicles. To overcome this, advanced basalt fiber reinforced polymer composites can be replaced with these wood materials, owing to the high melting point of basalt fiber. However, fire resistance characterization studies are limited to natural fiber composites of different fiber volume fractions, particularly for rock fibers. There is a need to identify the fiber volume fraction effect on fire resistance characteristics of composites for filling this research gap. In this study, mechanical, water absorption, and fire resistance properties of Basalt Rock Fibers (BRF) and Pineapple Leaf Fibers (PLF) reinforced polyester composite panels were investigated. The effect of fiber volume fractions ranging from 10% to 45% on the above-mentioned properties was studied. The theoretical Young’s modulus values were determined using the Halpin-Tsai model. Results indicated that the mechanical properties of BRF/polyester and PLF/polyester composites increased with the increase in fiber volume fraction (FVF) of up to 40% and 30%, respectively. The theoretical Young’s modulus values are in reasonably good agreement with the experiments. The percentage of the linear burning rate was found to be decreased, with the increase in FVF. It was found through the water absorption studies that PLF/polyester composites are hydrophilic whereas BRF/polyester composites are hydrophobic.
- 11 April 2021
- Published by Taylor & Francis in Journal of Natural Fibers
- Vol. 19 (13) , 6074-6088
Effect of Fiber Volume Fraction on Mechanical and Fire Resistance Properties of Basalt/Polyester and Pineapple/Polyester Composites
In general, the wood materials are used for constructing the buildings, passenger seats in trains and automobile doors. However, the progression of the fires due to the wooden construction is high when the fire accidents have occurred in the buildings, rail and road vehicles. To overcome this, advanced basalt fiber reinforced polymer composites can be replaced with these wood materials, owing to the high melting point of basalt fiber. However, fire resistance characterization studies are limited to natural fiber composites of different fiber volume fractions, particularly for rock fibers. There is a need to identify the fiber volume fraction effect on fire resistance characteristics of composites for filling this research gap. In this study, mechanical, water absorption, and fire resistance properties of Basalt Rock Fibers (BRF) and Pineapple Leaf Fibers (PLF) reinforced polyester composite panels were investigated. The effect of fiber volume fractions ranging from 10% to 45% on the above-mentioned properties was studied. The theoretical Young’s modulus values were determined using the Halpin-Tsai model. Results indicated that the mechanical properties of BRF/polyester and PLF/polyester composites increased with the increase in fiber volume fraction (FVF) of up to 40% and 30%, respectively. The theoretical Young’s modulus values are in reasonably good agreement with the experiments. The percentage of the linear burning rate was found to be decreased, with the increase in FVF. It was found through the water absorption studies that PLF/polyester composites are hydrophilic whereas BRF/polyester composites are hydrophobic.
- 10 November 2017
- Published by Springer Nature
- p. 179-185
A Study on Mechanical Properties of Treated Sisal Polyester Composites
- 10 November 2017
- Published by Springer Nature
- p. 179-185
A Study on Mechanical Properties of Treated Sisal Polyester Composites
- Open Access
- 1 January 2017
- Published by Elsevier in Procedia Engineering
- Vol. 173, 771-777
A Study on Impact Strength Characteristics of Coir Polyester Composites
- 1 January 2017
- Published by Elsevier in Procedia Engineering
- Vol. 173, 771-777
Open AccessA Study on Impact Strength Characteristics of Coir Polyester Composites
- Open Access
- 1 January 2017
- Published by Elsevier in Procedia Engineering
- Vol. 173, 778-785
Comparative Study of Impact Strength Characteristics of Treated and Untreated Sisal Polyester Composites
- 1 January 2017
- Published by Elsevier in Procedia Engineering
- Vol. 173, 778-785
Open AccessComparative Study of Impact Strength Characteristics of Treated and Untreated Sisal Polyester Composites
- 1 January 2017
- Published by Elsevier in Materials Today: Proceedings
- Vol. 4 (10) , 11050-11055
Probabilistic Study of Tensile and Flexure Properties of Untreated Jute Fiber Reinforced Polyester Composite
- 1 January 2017
- Published by Elsevier in Materials Today: Proceedings
- Vol. 4 (10) , 11050-11055
Probabilistic Study of Tensile and Flexure Properties of Untreated Jute Fiber Reinforced Polyester Composite
- 1 January 2016
- Published by Springer Nature
- p. 173-180
Prediction of Flexural Properties of Coir Polyester Composites by ANN
- 1 January 2016
- Published by Springer Nature
- p. 173-180
Prediction of Flexural Properties of Coir Polyester Composites by ANN
- 22 July 2013
- Published by Springer Nature
- p. 17-22
Prediction of Properties of CRPCSC Particulate Composite by ANN
- 22 July 2013
- Published by Springer Nature
- p. 17-22
Prediction of Properties of CRPCSC Particulate Composite by ANN
- 22 July 2013
- Published by Springer Nature
- p. 1-7
Prediction of Properties of Coir Fiber Reinforced Composite by ANN
- 22 July 2013
- Published by Springer Nature
- p. 1-7
Prediction of Properties of Coir Fiber Reinforced Composite by ANN