Abdulkareem Abubakar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Abdulkareem Abubakar has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Abdulaziz Al-Hashmi
Sultan Qaboos University
13 shared publications - Yahya Al-Wahaibi
Petroleum and chemical engineering department, Sultan Qaboos University, Muscat, Oman
13 shared publications A. Al-Ajmi
12 shared publicationsT. Al-Wahaibi
12 shared publicationsM. Eshrati
9 shared publications- Lawrence Chukwuka Edomwonyi-Otu
Department of Chemical Engineering, Ahmadu Bello University, Zaria, Nigeria
3 shared publications
Latest Publications
- Open Access
Global Research Trends in Catalysis for Green Hydrogen Production from Wastewater: A Bibliometric Study (2010–2024)
By turning a waste stream into a clean energy source, green hydrogen generation from wastewater provides a dual solution to energy and environmental problems. This study presents a thorough bibliometric analysis of research trends in the field of green hydrogen generation from wastewater between 2010 and 2024. A total of 221 publications were extracted from Scopus database, and VOSviewer (1.6.20) was used as a visualization tool to identify influential authors, institutions, collaborations, and thematic focus areas. The analysis revealed a significant increase in research output, with a peak of 122 publications in 2024, with a total of 705 citations. China had the most contributions with 60 publications, followed by India (30) and South Korea (26), indicating substantial regional involvement in Asia. Keyword co-occurrence and coauthorship network mapping revealed 779 distinct keywords grouped around key themes like electrolysis, hydrogen evolution reactions, and wastewater treatment. Significantly, this work was supported by contributions from 115 publication venues, with the International Journal of Hydrogen Energy emerging as the most active and cited source (40 articles, 539 citations). The multidisciplinary aspect of the area was highlighted by keyword co-occurrence analysis, which identified recurring themes including electrolysis, wastewater treatment, and hydrogen evolution processes. Interestingly, the most-cited study garnered 131 citations and discussed the availability of unconventional water sources for electrolysis. Although there is growing interest in the field, it is still in its initial phases, indicating a need for additional research, particularly in developing countries. This work offers a basic overview for researchers and policymakers who are focused on promoting the sustainable generation of green hydrogen from wastewater.
Open AccessGlobal Research Trends in Catalysis for Green Hydrogen Production from Wastewater: A Bibliometric Study (2010–2024)
By turning a waste stream into a clean energy source, green hydrogen generation from wastewater provides a dual solution to energy and environmental problems. This study presents a thorough bibliometric analysis of research trends in the field of green hydrogen generation from wastewater between 2010 and 2024. A total of 221 publications were extracted from Scopus database, and VOSviewer (1.6.20) was used as a visualization tool to identify influential authors, institutions, collaborations, and thematic focus areas. The analysis revealed a significant increase in research output, with a peak of 122 publications in 2024, with a total of 705 citations. China had the most contributions with 60 publications, followed by India (30) and South Korea (26), indicating substantial regional involvement in Asia. Keyword co-occurrence and coauthorship network mapping revealed 779 distinct keywords grouped around key themes like electrolysis, hydrogen evolution reactions, and wastewater treatment. Significantly, this work was supported by contributions from 115 publication venues, with the International Journal of Hydrogen Energy emerging as the most active and cited source (40 articles, 539 citations). The multidisciplinary aspect of the area was highlighted by keyword co-occurrence analysis, which identified recurring themes including electrolysis, wastewater treatment, and hydrogen evolution processes. Interestingly, the most-cited study garnered 131 citations and discussed the availability of unconventional water sources for electrolysis. Although there is growing interest in the field, it is still in its initial phases, indicating a need for additional research, particularly in developing countries. This work offers a basic overview for researchers and policymakers who are focused on promoting the sustainable generation of green hydrogen from wastewater.
- Open Access
- 1 January 2024
- Published by International Digital Organization for Scientific Information (IDOSI) in Iranica Journal of Energy and Environment
- Vol. 15 (1) , 10-20
Optimization of Process Parameters for Catalytic Pyrolysis of Waste Tyre using Reactivated Fluid Catalytic Cracking Catalyst
This work investigated the optimization of process parameters for catalytic pyrolysis of waste tyre using reactivated spent Fluid catalytic cracking (FCC) catalyst. The waste tyre pyrolysis used design expert software as the optimization tool for this study. A 3-factor level CCD with 20 experimental runs was used with temperature, time and catalyst as the input parameters while oil yield, density and viscosity were the output variables. Thereafter, an experimental validation of the optimized parameters, which were not among the original experimental runs, was carried out. Pyrolysis was also carried out at the optimized conditions with un-reactivated catalyst and without catalyst to ascertain the contributions of the catalyst and its reactivation. Based on the optimum parameters, 48.5 wt. % oil (0.79 g/ml and 2.05 cSt) was produced with the reactivated catalyst, 43.4 wt. % (0.86 g/ml and 3.52 cSt) was produced with spent catalyst, and 51 wt. % oil (0.95 g/ml and 4.24 cSt) was produced without catalyst. The oil yield without catalyst was higher than with reactivated catalyst (R-CAT); but it however had the lowest fuel qualities while oil produced with catalyst in turn had higher quantity and quality compared to oil produced with catalyst. Therefore, the incorporation of density and viscosity of the oil in the optimization of the catalytic pyrolysis of waste tyre enhanced the improvement of yield and quality of the oil produced.
- 1 January 2024
- Published by International Digital Organization for Scientific Information (IDOSI) in Iranica Journal of Energy and Environment
- Vol. 15 (1) , 10-20
Open AccessOptimization of Process Parameters for Catalytic Pyrolysis of Waste Tyre using Reactivated Fluid Catalytic Cracking Catalyst
This work investigated the optimization of process parameters for catalytic pyrolysis of waste tyre using reactivated spent Fluid catalytic cracking (FCC) catalyst. The waste tyre pyrolysis used design expert software as the optimization tool for this study. A 3-factor level CCD with 20 experimental runs was used with temperature, time and catalyst as the input parameters while oil yield, density and viscosity were the output variables. Thereafter, an experimental validation of the optimized parameters, which were not among the original experimental runs, was carried out. Pyrolysis was also carried out at the optimized conditions with un-reactivated catalyst and without catalyst to ascertain the contributions of the catalyst and its reactivation. Based on the optimum parameters, 48.5 wt. % oil (0.79 g/ml and 2.05 cSt) was produced with the reactivated catalyst, 43.4 wt. % (0.86 g/ml and 3.52 cSt) was produced with spent catalyst, and 51 wt. % oil (0.95 g/ml and 4.24 cSt) was produced without catalyst. The oil yield without catalyst was higher than with reactivated catalyst (R-CAT); but it however had the lowest fuel qualities while oil produced with catalyst in turn had higher quantity and quality compared to oil produced with catalyst. Therefore, the incorporation of density and viscosity of the oil in the optimization of the catalytic pyrolysis of waste tyre enhanced the improvement of yield and quality of the oil produced.
- Open Access
- 9 September 2021
- Published by Institute of Postgraduate Studies, Syiah Kuala University in Aceh International Journal of Science and Technology
- Vol. 10 (2) , 100-116
Use of Reactivated Spent FCC Catalyst as Adsorbent for Lead (II) Ions from Refinery-based Simulated Wastewater
Improper handling of wastewater from various industries causes environmental pollution. Hence, this study involved using a reactivated spent FCC catalyst, a cheap and reliable adsorbent for Pb2+ removal from refinery-based simulated wastewater. In contrast, response surface methodology (RSM) was used to determine the optimum operating condition. The adsorptive capacity of the reactivated spent FCC catalyst was observed using different parameters such as temperature, pH, adsorbent dosage, and contact time. At the end of the study, it was found that the optimum condition for removing Pb2+ was at pH of 7, adsorbent dose of 1.75 g, contact time of 75 mins, and temperature of 117 oC. At this condition, the maximum removal efficiency of Pb2+ was found to be 100 %. A quadratic model equation via central composite design under the RSM was developed to predict the Pb2+ removal from all the input parameters. Based on the F-statistic values, the temperature had the greatest influence on the removal of Pb2+ while adsorbent dosage and contact time were also significant.
- 9 September 2021
- Published by Institute of Postgraduate Studies, Syiah Kuala University in Aceh International Journal of Science and Technology
- Vol. 10 (2) , 100-116
Open AccessUse of Reactivated Spent FCC Catalyst as Adsorbent for Lead (II) Ions from Refinery-based Simulated Wastewater
Improper handling of wastewater from various industries causes environmental pollution. Hence, this study involved using a reactivated spent FCC catalyst, a cheap and reliable adsorbent for Pb2+ removal from refinery-based simulated wastewater. In contrast, response surface methodology (RSM) was used to determine the optimum operating condition. The adsorptive capacity of the reactivated spent FCC catalyst was observed using different parameters such as temperature, pH, adsorbent dosage, and contact time. At the end of the study, it was found that the optimum condition for removing Pb2+ was at pH of 7, adsorbent dose of 1.75 g, contact time of 75 mins, and temperature of 117 oC. At this condition, the maximum removal efficiency of Pb2+ was found to be 100 %. A quadratic model equation via central composite design under the RSM was developed to predict the Pb2+ removal from all the input parameters. Based on the F-statistic values, the temperature had the greatest influence on the removal of Pb2+ while adsorbent dosage and contact time were also significant.
- 29 July 2021
- Published by Springer Nature in Colloid and Polymer Science
- Vol. 299 (10) , 1521-1532
Water-soluble polymer-induced drag reduction and flow patterns for oil–water flows in return bend
- 29 July 2021
- Published by Springer Nature in Colloid and Polymer Science
- Vol. 299 (10) , 1521-1532
Water-soluble polymer-induced drag reduction and flow patterns for oil–water flows in return bend
- 27 February 2020
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 45 (9) , 7267-7273
Guar Gum as Flow Improver in Single-Phase Water and Liquid–Liquid Flows
- 27 February 2020
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 45 (9) , 7267-7273
Guar Gum as Flow Improver in Single-Phase Water and Liquid–Liquid Flows
- Open Access
- 8 March 2019
- Published by African Journals Online (AJOL) in Journal of Applied Sciences and Environmental Management
- Vol. 23 (2) , 209
Generation of empirical correlation for predicting drag reduction of oil-water flows with natural polymers
Generation of empirical correlation for predicting drag reduction of oil-water flows with natural polymers
- 8 March 2019
- Published by African Journals Online (AJOL) in Journal of Applied Sciences and Environmental Management
- Vol. 23 (2) , 209
Open AccessGeneration of empirical correlation for predicting drag reduction of oil-water flows with natural polymers
Generation of empirical correlation for predicting drag reduction of oil-water flows with natural polymers
- 1 March 2018
- Published by Elsevier in Journal of Petroleum Science and Engineering
- Vol. 162, 143-149
Effect of pipe diameter on horizontal oil-water flow before and after addition of drag-reducing polymer part II: Holdup and slip ratio
- 1 March 2018
- Published by Elsevier in Journal of Petroleum Science and Engineering
- Vol. 162, 143-149
Effect of pipe diameter on horizontal oil-water flow before and after addition of drag-reducing polymer part II: Holdup and slip ratio
- 1 May 2017
- Published by Elsevier in Experimental Thermal and Fluid Science
- Vol. 83, 169-176
Experimental study of drag reduction of polymer-polymer mixtures in horizontal dispersed oil-water flow
- 1 May 2017
- Published by Elsevier in Experimental Thermal and Fluid Science
- Vol. 83, 169-176
Experimental study of drag reduction of polymer-polymer mixtures in horizontal dispersed oil-water flow
- 1 March 2017
- Published by Elsevier in International Journal of Multiphase Flow
- Vol. 89, 359-374
Effect of pipe inclination on holdups/velocity ratios of oil-water flow without and with addition of drag-reducing polymer
- 1 March 2017
- Published by Elsevier in International Journal of Multiphase Flow
- Vol. 89, 359-374
Effect of pipe inclination on holdups/velocity ratios of oil-water flow without and with addition of drag-reducing polymer